2017 AUDI Q5 key

Opening and clo sin g
Convenience opening/closing
The windows and the Panoramic sliding sunroof*
can be opened and closed with the mechanical
key or the emergency key.
F ig . 40 Key turns for ope ning a nd clos ing
Con venienc e openin g fe ature
.,. Use the eme rgency key or pu ll the mechanical
key out of the master key ¢
page 34 .
! a,
.,. Insert the key into the lock of the driver's door .
.,. Turn the key to position¢
fig. 40 ® until all
the windows have reached the des ired position
and the Panoram ic sliding sunroof* is tilted.
Con venienc e clo sing f eatur e
.,. Use the emergency key or pull the mechanical
key out of the master key ¢
page 34.
.,. Turn the key in the lock of the driver's door to
the lock position @ until the w indows and the
Panoramic sliding sunroof* are closed¢,&. .
When you open or close the Panoramic sliding
sunroof*, the power sunshade will also open or
close.
A WARNING
- Never close the windows and the Panoramic sliding s unroof * inattentive ly and w ithout
check ing - there is risk of in jury .
- You must always watch when the w indows
are be ing raised so that no one can be trap­
ped.
If you release the key, the closing ac ­
t ion is immediately cance led.
- Always read and heed WARNING
c> &. in
General description on page 36 .
44
Correcting window regulator malfunction
After disconnecting the vehicle battery, the one­
touch up and down feature must be activated
agam .
.,. Pull and hold the power window switch until
the window is completely closed .
.,. Release the switch .
.,. Pull the sw itch agai n for one second. The auto­
matic closing/open ing is now reactivated.
Panorama roof
Operation
App lies to: vehicles wit h Pano ramic sliding s unroof
Fig . 41 Sect ion from head liner: Knob for Pa noram ic s lid in g
su nroof
Tilting
.,. The sunroof can be tilted or closed only in
sw itch position @
c> fig. 41
.,. To t ilt it, briefly press the switch¢ fig. 41.
.,. To close it, briefly pull the switch¢,&. .
.,. To se t an intermed iate posi tion, p ress/pu ll the
sw itch un til the sunroof reaches the desired po­
si tion.
Opening
.,. To move the sunroof to the position for red uced
w ind no ise, turn the switch to posit ion @ unt il
res istance can be felt.
.,. To open the sun roof complete ly, t urn and hold
the switch against the resistance in posit io n @ .
.,. To close the sunroof, turn the switch to posi­
tion @¢,&. .
.,. Turn the switch to the desired position to select
an intermediate position. .,.

Opening and closing th e sunshade
• To automat ica lly open the sunshade complete ­
l y, briefly press the switch@ in the desired ar­
row direction .
• To stop the sunshade in an intermediate posi­
tion, press the switch again, or
• Press and hold the switch in the desired arrow
direction.
• Release the switch when sunshade is at desired
pos it ion .
After the ign ition is switched off, you can still op­
erate the Panoramic sliding sunroof for about 10
minutes . As soon as the driver's or passenger's
door is opened, the switch is inoperative.
The power sunshade can also be closed when the
Panoram ic sliding sunroof is open.
A WARNING
Pay careful attent ion when closing the Panor­
am ic sliding sunroof -otherwise ser ious injury
could result! For this reason, always remove
the ignition key when leaving the vehicle.
@ Note
Always close your Panoramic sl iding sunroof
when leaving your vehicle . Sudden rain can
cause damage to the interior equipment of
your veh icle, particular ly the electronic equip­
ment .
@ Tips
Information regarding convenience opening/
clos ing
~ page 44.
Emergency closing of the Panoramic sliding
sunroof
Applies to: veh icles with Panoramic sliding sunroof
If the Panoramic sliding sunroof detects an ob­
ject in its path when it is closing, it will open
again automat ically. In this case, you can close
the roof with the power emergency closing func­
tion .
a,
~ • Within five seconds after the sunroof opens au-
~ tomatically, pull the switch until the roof
8 closes . 0
0:
co
Openin g an d clos ing
Garage door opener
(Homelink)
Description
Applies to: vehicles with garage door opener (Home link)
Fig. 42 Garage door opener: examples of using with differ­
ent systems
You can activate various systems such as garage
doors, security systems and home lighting from
inside your vehicle using the garage door opener
(Homelink) . There are three buttons for th is in
the vehicle headliner that can be in used in place
of up to three hand-held transmitters .
To operate systems using the garage door open­
er, the three buttons in the roof headliner must
be programmed first.
A WARNING
-
Make sure no peop le or objects are in the im-
mediate vicinity of the equipment when using
or p rogramm ing the ga rage door opener. Peo­
p le can be injured and objects can be dam­
aged if they are caught in the equipment.
(¼} Tips
- For security reasons, we recommend that
you clear the programmed buttons befo re
selling the vehicle .
- For add itiona l information about Homelink,
visit www.homelink.com.
- For Declaration of Compliance to United
States FCC and Indust ry Canada regulations
~page 279.
45

Lights and Vision
-Some exterior lighting functions can be ad ­
justed
c:>poge 50.
-When yo u remove your key from the igni ­
tion whi le the vehicle's lights are t urned on,
a buzzer sounds as long as the driver's door
i s open.
- In cool or damp weather, the inside of the
headlights, turn s ignals and tail lights can
fog over due to the temperature d ifference
between the inside and outs ide. They will
clear short ly after sw itch ing them on. This
does not affect the serv ice life of the light­
i ng.
- In the event of a light se nsor mal funct ion,
the driver is not ified in the instr ument clus ­
te r d is p lay
c;, pag e 29.
Fog lights
Fig . 4 6 Fog lig ht switch
• To turn on the fog lights }D, press button @
c:>fig. 46 .
• To turn on the rea r fog lights 0$, press button
@ .
Fog lights
The s ide marker lights or low beams must be
sw itched on. Whe n the fog lights are sw itched
on, the g reen check light at the edge of the
sw itch comes o n.
If automat ic driving light control AUTO is activat­
ed, the low beams are sw itched on when the fog
lights are turned on.
Rear fog lights
Low beams or side marker lights with fog lights
must be turned on.
50
When the rear fog lights are turned on, the yel ­
l ow check light at t he edge of the switch comes
on .
(D Note
The re ar fog lig hts should on ly be t urned on in
accor dance with traffic reg ulation, as the
li ghts are bright for following t raff ic .
Adjusting exterior lighting
The functions ore selected in the radio or in the
MMI".
• Sele ct: I CAR I func tion b utton > Exterior light­
ing . Or
• Select:
-1 c- A~ R~! function b utton > Car systems *
control button > Vehicle settings > E xterior
lighting .
Coming home (Lights when leaving car),
Leaving home (Light s when unlock ing ca r)
The coming home function ill uminates the area
outside the vehicle when you turn the ignit ion
off
and open the driver's door . Depending on vehicle
equipment, the function ca n be sw itched on and
off or the length of time the lights remain o n*
can be adj usted.
The leaving home illum inates the area outside
the ve hicle when you unlock the vehicle. This
funct ion can be switched on and off .
The Coming home and Leaving home functions
on ly operate when it is dark and the light switc h
i s in the
AUTO pos ition.
Auto headlights
When the light sw itch is in the AUTO c:> page 49
pos ition, the switch-on point of the lights can be
c hanged in the automat ic driving light function.
Daytime running lights
USA models: You can switch the daytime runn ing
li ghts
On and Off .
Canada model s:
The function canno t be tur ned
off.
It i s a ct ivate d automatically ea ch time the ig-
nit ion is switched on.
liJI.

a,
a,
..... N r-­N ..... 0 0
0:
co
The mirror returns to its initial position as soon
as reverse gear is dis e ngaged and vehicle speed is
above about 9 mph (15 km/h) . T he mirror also
returns to its ini tial posit ion if the switch is
moved to the driver's exter ior mirror © or the ig­
n ition is switched off .
If the position of the m irror surface is changed
on a ti lted mirror , this new position will be auto­
matically assigned to the remote key when the
vehicle is taken out of reverse gear .
(D Note
- Curved mirror surfaces (convex or spheri­
cal") increase your field of v iew . Remember
that vehicles or other objects will appear
smaller and farther away than when seen in
a flat mirror . If you use th is m irror to esti­
ma te distances of following vehicles when
changing lanes, yo u could estimate incor­
rectly and cause an a ccident.
- If the mir ror housing is moved unin tention­
ally (for example, wh ile pa rking yo ur vehi­
cle), then you must first fold the m irror
electrica lly. Do not read just the mirror
hous ing manua lly. You could damage the
motor which contro ls the mirror.
- If you wash the vehicle in an automatic car
wash, yo u m ust fold the exterior m irrors in
to reduce the risk of damage to the mirrors. Never fold power folding exterior m irrors*
by hand . Only fold them in and out using
the power contro ls .
@ Tips
If there should be a ma lfunction in the e lec­
trical system, you can still adjust the exterior m irro rs by p ressing the edge of the m irror .
Lights and V ision
Dimming the mirrors
Fig. 60 Auto ma tic dimmin g rearvi ew m irror*
Manu al anti-glare adjustment
.. Move the small lever ( located on the bottom
edge of the mirror) to the rear .
Automat ically dimm ing mirro rs*
.. To dim the rearview mir ror and both exterior
m irrors *, press the@ button. The diode @
turns on . The rearv iew and exterior mirrors*
dim automatically when light shines on them ,
for example from headlights on a veh icle to the
rear .
_&. WARNING
-Electrolyte flu id can leak from automatic d im­
ming m irrors if the glass is broken. Ele ctro­
l yte fluid can i rr itate sk in, eyes and respirato­
ry system .
- Repeated or p rolonged exposure to electro­
ly te ca n cause irri tat ion to the resp iratory
system, especially among people with asth ­
ma or other respiratory conditions. Get
fresh air immediately by leaving the vehicle
or, if that is not possible, open windows and
doors all the way.
- If electro lyte gets into the eyes, flush them
thorough ly w ith large amounts of clean wa ­
ter for at least 15 m inutes; medical atten­
tion is recomme nded .
- If electrolyte contacts skin, flush affected
area with clean water for at least 15 mi­
nutes and then wash affected area with
soap and water; medical attention is recom­ mended. Thoroughly wash affected cloth ing
and shoes before reuse .
~
57

a,
a,
..... N ,....
N ..... 0 0
0:
co
Front passenger's seat
Always move the front pas senger seat into the
rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instrument
panel than necessary and always wear the three ­
point safety belt provided adjusted correctly . We
recommend that you adjust the passenger's seat
in the following manner:
.. Move the front passenger seat into the rear ­
most position of the fore and aft adjustment
range
c;> .&. in Why is your seat adjustment so
important? on page 60.
• Bring the backrest up to an (almost) upright
position.
Do not ride with the seat reclined .
.. Adjust the head restraint so the upper edge is
as even as possible with the top of your head. If
that is not possible, try to adjust the head re­
straint so that it is as close to this position as
possible
c;> page 64 .
.. Place your feet on the floor in front of the pas ­
senger's seat .
Front seats
Power seat adjustment
Fig. 63 Fro nt seat: Contro ls fo r seat adjus tme nt
Controls
"' 0 ci: a, a,
@ -Adjusting the lumbar support: press the but­
ton in the corresponding position¢
Le,..
@ -Moving the seat up/down : press the button
up/down . To adjust the front seat cushion, press
the front button up/down. To adjust the rear seat
cushion, press the rear button up/down¢
Le,. .
Seats and storage
@-Moving the seat forward/back: press the but­
ton forward/back
~ & .
©-Adjusting the backrest angle: press the but­
ton forward/back
c;> & .
@ -Lengthening/shortening the upper thigh
support*: lift the handle
c;> Le,. .
_&. WARNING
- Never adjust the driver's or front passeng­
er 's seat while the vehicle is moving.
If you
do this while the vehicle is moving, you will
be out of position . Always adjust the driver's
or front passenger's seat when the vehicle is
not moving.
- Be careful when adjusting the seat height.
Check to see that no one is in the way, or se­
rious injury could result!
- Because the seats can be electrically adjust­
ed with the ignition off or with the ignition
key removed, never leave children unattend­
ed in the vehicle . Unsupervised use of the
electric seat adjustments may cause serious injury .
- To reduce the risk of injury in the case of
sudden braking or accident, front passen­
gers must never ride in a moving veh icle
with the backrest reclined. Safety belts and
the airbag system only offer maximum pro­
tection when the backrest is upright and the
safety belts are properly positioned on the
body. The more the backrest is reclined, the
greater the risk of personal injury from an
incorrect seating position and improperly
positioned safety belts.
-
61

Sea ts and stor age
Memory function
Memory for driver's seat
Applies to: vehicles with seat memory
The seat adjustment settings for two drivers can
be stored using the memory buttons in the driv ­
e r's door.
F ig . 64 Dr ive r's doo r: Sea t memory
i ci: co a,
In addition to the setting for the drive r's seat,
the exterior rear view mirror setting can be stor­ ed and recalled through seat memory if the vehi­
cle is properly equipped .
Storing and re calling s ettings
With the help of the memory buttons 1 and 2
c> fig . 64 the settings for two different drivers
can be stored and recalled
¢ page 62.
The cu rrent se ttings are also automatically as ­
signed to the remote contro l key being used
when the vehicle is locked . When the vehicle is
un locked , the settings assigned to the remote
control key being used are automatically recal­
led.
Tu rnin g se at memo ry on and off
If the IO FFI switch is depressed, the seat memory
is inoperative. When the Memory function is off,
the LED in the button lights up.
All t he s tored se tt ings are retai ned. We recom­
mend using the
I O FF I sw itch and deactivating the
seat memory if the vehicle is on ly going to be
used
temporarily by a driver whose settings are
not going to be stored.
62
Stor ing and recalling settings
Applies to: vehicles with seat memory
Storing settings
.,. Adjust the driver's seat .
.,. Adjust the two exterior mirrors.
.,. Press the
ISETI button . The light in the button
w ill come o n.
.,. Now press a memory button
dII or I]]) . If the
storing procedu re is correct, a confirmation
tone will sound.
Recalling settings
"' If the driver's door is open and the ignition is
sw itched off, tap the corresponding memory
button briefly .
.,. If the driver's door is closed or the ignition is
switched on, press the appropriate memory
button until the stored position is reached .
Successful storage is confirmed audib ly and by
the light in the
ISE TI button illuminating
c> page 62, fig. 64 .
When the vehicle is locked , the current settings
are stored and assigned to the remote control
key . But the settings stored on memory buttons
1 to 2 are not de leted. They can be recalled at
any time . When the vehicle is
unlocked , the set­
tings assigned to the remote control key a re re­
stored .
If your vehicle is driven by other persons using
your remote control key, you should save your in­ dividual seat position on one of the memory but­
tons . You can recall your settings again simply
and conveniently by p ressing the correspond ing
memory button. When the vehicle is locked,
these settings are automatically re-ass igned to
the remo te contro l key and stored.
A WARNING
- For safety reasons, the seat sett ing can only
be reca lled when the vehicle is stationary­
otherwise yo u ris k having an accident.
- In an emergency the reca ll proced ure can be
cancelled by pressing the
! OF F! switch or by
tapping of the memory buttons.

a,
a,
..... N r--­N ..... 0 0
0:
co
Activating remote control key memory
Applies to: vehicles with seat memory
To assig n the drive r's seat settings to the remote
con trol key when locking the vehicle , the function
must be act ivated in the ra dio or M MI* .
• Se lect :
I CARI funct ion button > Seat adjust­
ment > Driver's seat > Key mem. profile > On .
Or
• Se lect :
I CARI funct ion but ton> Car sy stem s*
contro l bu tton > V ehicle setting s > Seat s>
Dri ver' s seat > Remote control key > On .
(D Tips
If you do not wa nt ano ther d river's settings to
be assigned to the remote control key, sw itch
off the memory funct ion using the rad io or
M MI* or the
!OF F! button 9 page 62 .
Rear seat
General information
Safe transportation of passengers on the rear
seats requires proper safety precautions .
All passengers on the rear seats must be sea ted
in comp lia nce w it h the safety guidelines ex ­
p la ined in
<=;> page 140 and .:;,page 148. The co r­
r ect seating posit ion is critical for the safety of
fron t
and rear seat passenge rs al ik e r::!;> page 134 .
A WARNING
- Occupan ts in the fro nt and rear sea ts m ust
always be properly res trai ned.
- Do not let anyone ri de in t he vehicle with ou t
th e head restra ints prov ided. He ad re­
st raints help to reduce injuries.
- L oose i tems inside the passenger compa rt­
ment, can f ly forwa rd in a cras h or sudden
maneuver and injure occupants. Always
store articles in the luggage compartment
and use the fasten ing eyes , especia lly when
the rear seatbacks have been folded down.
- Read and heed a ll WARNINGS
¢ page 134,
Proper seating positions for passengers in
rear s eats .
Seats and storag e
Adjusting seat
The fore-and-aft adjustment of the seat cushion
and the seatback angle con be adjusted .
Fig . 65 Adjust ing seatbac k angle
Fig. 66 Fo re -a n d-a ft a dju stm ent
Adjusting seatback angle
• Pull the lever up and pus h the seat back t oward
the rear to the des ired position
r::!;> fig . 65 . Re­
lease the lever.
• Pull the lever up so that the seatback pivots
forward. Release the lever and push the seat­
back to the rear to ret urn the seatback to the
normal pos ition .
Fore-and-aft adju stment
• Pull the handle up and pus h the seat forward or
back
<=;> fig. 66 .
• Release the handle and continue to push the
sea t unt il the seat latch engages .
A WARNING
- For safety reasons, the seat m ust only be
ad juste d when t he vehicle is st ationary -
da nger of acc iden t!
63

Seats and storage
-Exercise caution when adjusting the seat .
Adjusting the seat without checking or pay­
ing attention can pinch fingers or limbs -
danger of injury!
Head restraints
Front head restraints
Fig. 67 Fro nt seats head restrai nts: adj ust ing the he ig h t
The head restra ints on the front seats can be ad­
justed to provide safe suppo rt to head and neck
at the optimum height . When optimally adjust­
ed, the top of the restraint should be level wi th
the top of the head. If that is not possible, try to
adjust the head restraint so that it is as close to
this position as possibler::!;>
page 134, Proper ad­
justment of head restraints.
• Grasp the sid es of the head restraint with both
hands and slide it upward/downward until you
feel it click into place r::!;>
fig. 67.
Refer to
r::!;> page 134, Proper adjustment of head
restraints
for guidelines on how to adjust the
height of the front head restra ints to suit the oc­
cupant 's body size.
_&. WARNING
- Driving without head restraints or with head
restraints that are not properly adjusted in­
creases the risk of ser ious or fatal neck in­
jury dramatically .
- Read and heed all WARNINGS
c:> page 134,
Proper adjustment of head restraints.
64
@ Tips
Correctly adjusted head restraints and safety
belts are an extreme ly effective combinat ion
of safety features.
Rear head restraints
Fig. 68 Rear seat : head rest raints
Fig. 69 Rear sea t: ou ter head restrain t
If there is a passenger on the rear center seating
position, slide the center head restraint upward
at least to the next notch
c:> .&_ .
Adjusting the head restraints
• To move the head restraint up, hold it at the
sides with both hands and slide it upward until
you feel it click into place.
• To move the head restraint down, press the
button @and slide the head restraint down­
ward .
Removing the outer head restraints
• Fold the backrest forward r::!;> page 66.
• Move the head restra int upward as far as it can
go .
.,. Press the release@<=>
fig. 69 with the mechan­
ical key
c:> page 34 and the button@<=> fig. 68. Iii>-