2017 AUDI A8 wheel bolt torque

Emergency assistance
Emergency assistance
General information
... Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tir e, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
... Set up the warning triangle
r=;, page 312 .
... Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
Applies to: vehicles with warning triangle
Fig. 271 L uggage compa rtm ent lid : w arnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
... To remove the warning triangle, press the fas-
tener in the direction of the arrow and fold the
holder down.
The luggage compartment lid is only designed to
hold the warning triangle offered by th e Audi
Genuine Accessories program.
312
Vehicle tool kit
Applies to: vehicles with vehicle toot kit
Fig. 272 L u gg age compartmen t: cargo floor cove r fo lded
upward
Fig. 273 Luggage co m partment: exa mple of veh icle toot
kit and vehicle j ack
The vehicle tools and vehicle jack* are stored in
the luggage compartment under the floor cover .
... Lift the cargo floor by the plastic handle .
... Hook the handle into the luggage compartment
seal
r::> fig. 272 .
.,. Turn the handwheel counter-clockwise and re ­
move it .
.,. Remove the spare tire* to access the vehicle
tool kit
r::;, fig. 2 72 .
Depend ing on the equipment , the veh icle tool kit
may be located under the spare tire, under an­
other cover or in the tool box.
T he position of the vehicle jack* may vary .
A WARNING
Improper use of the veh icle jack can cause se ­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you .,..

Emergency assistance
7. Tighten all wheel bo lts light ly .
8. Lower the veh icle with the jack .
9. Use the whee l bolt wrench and firmly tighten
all whee l bolts
<=:> page 315.
10. Replace the decorative wheel cover* .
11. Deactivate the vehicle jack mode in the MMI:
I CA R I function butto n > Car systems control
b utton
> Servicing & checks > Air susp.: jack
mode > Off .
The vehicle jack mode switches off automat ically
at s peeds above
10 km/ h.
,& WARNING
Alw ays read and fo llow all WAR NIN GS and in ­
f o rm at ion
c;, .&. in AB: R ais ing the vehi cle on
p oge316 and <=:>page 319.
After changing a wheel
A wheel change is not complete without the do­
ing the following.
• Always store the veh icle tool kit, the jack* a nd
the replaced t ire in the luggage compartment
<=:> page 213.
• Che ck the tire pressure on the sp are whee l im­
med iate ly after mo unti ng it .
• As soon as possible, have the
tightening tor­
ques
on all whee l bo lts chec ked with a torque
wrench. The correct tightening torque is 90 ft
lb
(120 N m).
• Have the flat tire
replaced as soon as possible.
(D Tips
- If you notice t hat the whee l bolts are cor ­
r oded and diffic ult to t urn w hile cha nging a
tire, they should be rep laced before you
c heck the tighte ning torque .
- Drive at reduced speed until you have the
tighte ning torques c hecke d.
- After changing a wheel, the tire pressure in
all four tires must be c heck ed/co rrect ed a nd
the tire press ure mon itor ing indicato r must
be stor ed in the MM I
<=:> page 302 .
314 Decorative wheel covers
App
lies to: vehicles with decorative w heel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig. 274 Changi ng a whee l: Removing t he whee l cover
Removing
• Insert t he hook (p rovided w ith the vehicle tool
ki t) i n the hole in the w heel hu b cover .
• Pull off the
decorative wheel cover <=:> fig. 2 7 4.
Wheels with wheel bolt caps
Applies to: vehicles wit h wheel bolts with caps
The cops mus t be removed fir st from the wheel
bol ts before the bol ts con be unscrewed.
Fig. 275 C ha ng ing a w heel: remov ing th e w heel bo lt caps
Removing
• Push t he plastic clip (prov ided with the vehicle
tool kit) over the whee l bolt cap until the inne r
reta iners on the clip a lign with t he edge of the
cover.
• Remove the cap wi th t he
plastic clip (vehicle
t oo l kit )
c;, fig. 2 75.
Refitting
• Place the caps over the whee l bolts and push
them back on .

C) C0 ....
"' " "' .... 0 0 :r Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right dir ection .
Using a spare tire w ith a tread pattern
intended for use in a specific direction
When using a spare t ire with a tread patte rn in­
ten ded fo r use in a specific direction, please note
the following:
- The direct io n of rotat io n is ma rked by an a rrow
o n the side of the tire .
- If the spare tire has to be installed in the incor­
rect d irection, use the spare tire only tempora­
rily s ince the tire w ill not be ab le to achieve its
opt imum performanc e ch a rac teristics wi th re ­
g ard to a quaplaning, noi se and we ar.
- We recommend that you pay particular atten­
t io n t o thi s fa ct du ring we t wea ther and that
y ou adju st your s peed to m atch r oad co ndi­
ti ons .
- R eplace t he flat tir e wi th a new one and have i t
i n st alled on yo ur vehicle as soon as possible to
r es to re the handlin g advanta ges of a unidi rec­
tiona l tire .
Notes on wheel changing
P lease read the info rmation
<=> page 29 0 if you
are going to use a spare tire which is different
from t he tires on your vehicle.
Afte r you change a ti re:
- Check the tire pressure on the spare immedi ­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb (120 Nm).
- If you notice that the wheel bolts are corroded
and diff icult to turn while changing a tire,
they should be replaced before you check the
tightening torque .
Emergency assistance
-Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover .
Until then , drive with extra care and at reduced
speeds.
A WARNING
- If you are goin g to equip yo ur ve hicle with
tires or r ims which diffe r from those which
were factory installed, the n be sure to read
the information
r:> page 290.
- A lways make sure the dama ged w heel or
e ven a flat tire and the jack and tool kit ar e
prope rly sec ured in the luggage compa rt­
men t and a re not loose in the passenger
compa rtme nt.
- In an accident or sudde n maneuv er th ey
co uld f ly forward , inju ri ng a nyone in the ve­
h icle.
- Always store damaged w he el, jack and tools
se cur ely in the luggage compartment. Ot h­
e rw ise, i n an accide nt or sud den mane uve r
t hey could fly forw ard, causing inju ry to pas ­
s e ng ers i n th e ve hicle.
Spare tires
General information
App lies to : vehicles wi th spare tire/space-saving spare tire
(co mp act s pa re t ire)
Fig . 28 3 Lu ggage co mpart m ent: ca rgo floo r cover fo lded
up wa rd
The spare tire is intended for s hort-term use on-
-
ly . Have the damaged tire checked and, if neces­
sary, rep laced by an authorized A udi dealer or au­
tho rize d Au di Serv ice Facility as soon as p ossible.
II>-
319