2017 AUDI A7 battery

Airbag syste m
must be performed by qualified workshops
only. Make sure that any airbag service ac­
tion is entered in your Aud i Warranty
&
Maintena nce booklet under AIRBAG RE­
PLACEMENT RECORD.
- For safety reasons in severe accidents, the
alternator and starter are separated from
the vehicle battery with a pyrotechn ic circuit
in terrupter.
- Work on the pyrotechnic circuit interrupt­
er must only be performed by a qualified
technicians who have the experience, in­
formation and special tools necessary to
perform the work safely.
- If the vehicle or the circuit interrupter is
scrapped, all applicab le safety precautions
must be followed .
@ For the sake of the environment
Undeployed airbag modu les and pretension ­
ers might be classified as Perch lorate Materi­
al -special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlo­ rate . When the veh icle o r parts of the re­
stra int system including airbag modules and
safety belts w it h pretensioners are scrapped,
all applicable laws and regu lations must be
observed. Your authorized Audi dealer is fa­
m iliar with these requirements and we recom ­
mend that you have your dealer perform this
serv ice for you.
Other things that can affect Advanced
Airbag performance
Changing the vehicle's suspension system can
change the way that the Advanced A irbag System
pe rforms in a crash. For e xamp le, using t ire -r im
comb inations no t approved by Audi, lowering t he
veh icle, chang ing the stiffness o f the suspe nsio n,
i n cluding the springs, suspension struts, shock
absorbers etc . can change the forces that are
measured by the airbag sensors and sent to the
electronic contro l unit . Some suspens ion changes
can, for example, increase the force levels meas­
ured by the sensors and make the airbag system
deploy in c rashes in w hich it would not deploy if
the changes had not been made. Other ki nds of
164
changes may reduce the force levels measured by
the sensors and prevent the airbag from deploy­
i ng when it should .
_& WARNING
Changing the vehicle's suspension including
use of unapproved tire-rim comb inations can
change Advanced Airbag performance and in­
crease the r isk of serious personal injury in a
crash .
- Never install suspension components that do not have the same performance charac­
ter istics as the components origina lly instal­
led on your vehicle.
- Never use tire-r im combinations that have
not been approved by Aud i.
Knee airbags
Description of knee airbags
Applies to : vehicles with knee airbags
The knee airbag system can provide supplemen­
tal protection to properly restrained front seat
occupants .
Fig . 15 9 Driver 's knee a irbag
The driver knee airbag is in the instrument panel
u nderneath the s teer ing whee l¢
fig. 159, the
airbag fo r the passenger is at about the same
height in the i nstr ument panel underneath the
glove compa rtment.
The knee airbag offers add itiona l protect ion to
the d river's and passenge r's knees and uppe r and
l ower thigh areas a nd sup plements the p rotec­
t ion prov ided by the safety belts .
If the front airbags deploy, the knee a irbags also
deploy in fron tal coll is ions when t he deployment ..,_

Checking and Filling
-Do not remove the engine cover under any
circumstances . This increases the risk of
burns.
- If tests need to be performed with the en­
gine running, there is additional danger due
to moving components (such as the ribbed belt, alternator and radiator fan) and from
the high voltage ignition system.
- Do not under any circumstances give gas in­
advertently (for example, by hand from the
engine compartment) if the vehicle is sta­
tionary but the engine is running and a gear
is engaged. Otherwise, the vehicle will start
to move immediately and this could result
in an accident.
- Pay attention to the following warnings list­
ed when work on the fuel system or on the
electrical equipment is required.
- Do not smoke .
- Never work near open flames.
- Always have a working fire extinguisher
nearby
- All work on the battery or electrical system
in your vehicle can result in injuries, chemi·
cal burns, accidents or burns. Because of
this, all work must be performed
only by an
authorized Audi dealer or authorized Audi
Service Facility.
- To reduce the risk of electric shock and in­
jury, never touch the following components when the engine is running or is being start­
ed :
- Ignition cable
- Other components in the electronic high-
voltage ignition system
-If you must check or perform work on the
engine while it is running:
- Set the parking brake and place the selec­
tor lever in the P (park) position first .
- Always proceed with extreme caution so
that clothing, jewelry or long hair do not
become caught in the radiator fan, fan
belt or other moving components or do
not come into contact with hot compo­
nents. Tie back long hair before beginning
work and do not wear clothing that can
hang down into the engine.
200
-Limit your exposure to exhaust and chemi­
cals to as short a time as possible
c> A .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and
reproductive harm . In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
(D Note
When filling fluids, be sure not to mix the flu­
ids up. Otherwise severe malfunctions and en­
gine damage will occur.
@:) For the sake of the environment
You should regularly check the ground under
your vehicle in order to detect leaks quickly. If
there are visible spots from oil or other fluids, bring your vehicle to an authorized Audi deal­
er or authori zed Audi Service Facility to be
checked.

co
_& WARNING
-The cooling system is under pressure. Do
not open the coolant expansion tank cap
when the engine is hot. This increases the
risk of burns .
- The coolant add itive and the coolant can be
dangerous to your health. For this reason,
keep the coolant in the original container
and away from children. There is a risk of
poisoning.
- When working in the engine compartment ,
remember that the radiator fan can sw itch
on even if the ignition is switched off, which
increases the risk of injury.
CD Note
Do not add coolant if the expansion tank is
empty. Air could enter the cooling system and
damage the engine. If this is the case, do not
continue driv ing. See an authorized Audi deal­
er or authorized Audi Service Facility for assis­
tance .
Brake fluid
N
N
-N
" co IXl
Fig. 187 Engine co mp artment : cap on brake fl uid re se rv oir
Observe the safety precautions c:> &. in Working
in the engine compartment on page 199.
Checking the brake fluid level
" Read the brake fluid level on the brake fluid
reservoir i=>page 202, fig . 184. The brake fluid
level must be between the MIN and MAX mark­
ings
c:> &_ .
~ The brake fluid level is mon itored automatically .
" N .... 0
00
<..:l 'SI"
Checking and Filling
Changing the brake fluid
Have the brake fluid changed regularly by an au­
thorized Audi deal er or authorized Audi Service
Facility.
A WARNING
-
- If the brake fluid level is below the MIN
marking, it can impair the braking effect
and driving safety, which increase the risk of
an accident . Do not continue dr iving . See an
author ized Audi dealer or author ized Audi
Service Facility for assistance.
- If the brake fluid is old, bubbles may form
in the brake system dur ing heavy braking .
This would impair braking performance and
driving safety, which increases the r isk of an
accident.
- To ensure the brake system functions cor­
rectly, only use brake fluids that comply
with VW standard 50114 or FM VSS -116 DOT 4.
CD Note
-If the brake f luid level is above the MAX
marking, brake f luid may leak out over the
edge of the reservoir and result in damage
to the vehicle.
- Do not get any brake fluid on the vehicle
paint, because it wi ll corrode the paint.
Battery
General warnings about batteries
Because of the complex power supply, all wo rk
on batter ies such as disconnecting, replac ing,
etc. should
only be performed by an authorized
Audi dealer or authorized Audi Service Fac il ity
c:> & .
The term "vehicle battery" refers to the 12 Volt
battery in your vehicle.
Detailed warnings for the vehicle battery:
® Wear eye protection.
I.)._ Bat~ery acid is highly corrosiv~. We ar p ro -
~ tect1ve gloves and eye protection. Ill-
207

Checking and Filling
@
Fire, sparks, open flame and smok ing are
forb idden.
~
A highly explosive mixture of gases can
form when charging batteries.
®
Keep c hildren away from bat tery acid and
batteries.
A WARNING
All work on the battery or electrica l system in
your vehicle can result in injuries, chemical
burns, accidents or burns. Because of this, a ll
work m ust be performed
only by an author­
ized Aud i dea le r o r autho rized Aud i Serv ice
Facili ty.
A WARNING
California Proposit io n 65 Warning:
- Battery posts, termina ls and re lated acces­
so ries contai n lead and lead compounds,
chemicals known to the Sta te of Californi a
to ca u se ca nce r and rep roduct ive p roblems.
Wash hands after handling.
0 Note
Protect the vehicle ba ttery against freezing if
t he vehicle will be p arked for long per iods of
time so th at it is not destroyed by "free zing"
¢page 208.
@ For the sake of the environment
~ Batteries cont ain poll utin g substances suc h
as s ulfu ric ac id and lead. Contac t an a uthor­
ized Audi dealer or aut horized Audi Service
Facility for more information.
Vehicle battery
The term "vehicle battery" refers to the 12 Volt
battery in your vehicle.
Not running the vehicle for long periods of
time
If you do not drive your ve hicle for seve ral days or
weeks, e lec trical equipment is gradually scaled
back or switched off. This reduces energy use and
ensures the veh icle wi ll be able to start after long
periods of timer=;,
page 126 . Some conven ience
208
funct ions, such as interior lighting o r power seat
adjustment, may not be avai lab le under certain
c ircumstances. These convenience functions will
be available again once you switch the ignition on
and start the eng ine.
Even when electrical equipment is switched off,
the eq uipment can st ill dra in the vehicle batte ry
if the veh icle is not dr iven for long pe riods of
time . Deep drai ning results in a chemica l reaction
that destroys t he ins ide of the vehicle battery .
The vehicle battery must be charged every mon th
to reduce the risk of this happening r=;,
page 208.
Contact an a uth o rized Aud i dea le r or a uth o rized
Audi Se rvice Fac ility for mo re informa tion.
Winter operat ion
Co ld weather places higher demands on the vehi ­
cle battery . T his res ults in reduced starting ab ili­
ty. Have the vehicle batte ry checked by an au­
thorized Audi dea le r or authori zed Audi Service
Fac ility befo re t he cold time of year.
Charging the vehicle battery
Fi g. 1 88 En g ine compa rt m ent: con nectors fo r a c ha rge r
and j ump start cab les
Requirement: only use chargers with a maximum
charging voltage of 30 amp s/14 .8 Volts .
The
vehicle battery cab les remain connected .
.. Read the warnings r=;,
A in General warnings
about batteries on page 208
and r=;, A.
.. Switch off the ign it ion and all electrica l equ ip­
ment.
.. Open the hood r=;,
page 201.
.. Open the red cover on the pos itive terminal
~ fig . 188.

co
co
,...,
N
" N ,...,
0
00
\.J ' ~ Clamp the charger terminal clamps to the jump
start pins according to the instructions. (pin un­
der the red cover = "positive", pin with hexago ­
nal head = "negative").
~ Insert the power cable for the charging device
into the socket and switch the device on .
~ At the end of the charging process, switch the
charger off and pull the power cab le out of the
socket.
~ Remove the c harge r te rmi nal clamps.
~ Close the red cover on the positive term inal.
~ Close the hood ¢ page 201.
A WARNING
- A highly explosive mixtu re of gases can form
when charging batter ies. On ly charge the
vehicle battery in well-vent ilated areas.
- A drained battery can freeze at tempera­
tures around 32 °F (0 °C). A frozen or
thawed vehicle battery must not be charged
and must not be used anymore . The battery
housing can crack and battery acid can leak
out if ice fo rms, wh ich increases the r is k of
an exp losion and chemical burns , Contact an
au thori zed Aud i dealer o r autho riz ed Aud i
Service Facility fo r more information.
- Do not con nect o r disconne ct the c harg ing
c able while charg ing be cause th is increases
the risk of an exp losion.
(j) Tips
- Only cha rge the vehicle bat tery through t he
con nections in the engine compartmen t.
- Read all of the manufacture r's instructions
fo r the charger befo re c harg ing the ve hicl e
batte ry.
Ch eck ing and Filling
Windshield washer
system
Fi g. 1 89 E ngine compar tmen t: washer f luid reservo ir cap
M N
-N ~
"' m
The windshield washer rese rvoir O contains the
cleaning so lution for the windshield and the
headlight washer system*
q page 202, fig. 184.
The reservoir capacity can be found in
¢page 262.
To reduce the risk of lime scale depos its on the
spray nozzles, use clean water with low amo unts
of calcium. Always add w indow cleaner to the wa­
ter. When the outside temperatures are cold, an
anti-freezing agent shou ld be added to th e water
so that it does not freeze .
(!) Note
-The concentration of ant i-freez ing agent
must be adjusted to the vehicle operat ing
conditions in the respective climate . A con­
centration that is too high can lead to vehi­
cle damage.
- Never add radiator anti-freeze or other addi­
tives to the washer fluid.
- Do not use a glass cleaner that contains
paint so lvents, because th is could damage
the paint.
Service interval display
The service in terval display detects when your ve­
hicle is due for service.
T he serv ice inte rval d isplay wo rks in two stages:
-Inspect ion or oil change rem inder: after a cer-
tain distance driven, a message appears in the ..,.
209

Check ing and F illing
instrument cluster display each time the ign i­
tion is switched on or off . The remaining dis­
tance or time is displayed br iefly.
- Inspection or oil change due: if yo ur vehicle
has reached an inspection o r oi l change interval
or both intervals at the same time, the mes­
sage
Inspection due! or Oil change due! or Oil
change and inspection due!
appears briefly af­
ter switch ing the ignit ion on/off .
Checking service intervals
You can check the rema ining distance o r time un­
til the next oil change o r next inspection in the
Car menu. To do this, select : the
IC ARI function
button
> (Car) * Systems control button > Service
& checks > Service interv als .
Resetting the indicator
Your author ized Audi dealer or authoriz ed A udi
Serv ice Facility will reset the serv ice interval d is­
p lay after performing serv ice.
If you have changed the oil yourself, you must re ­
set the oil change interva l.
fo reset the indica to r, se lec t: the
ICAR I fu nction
but ton
> (Car) * Systems con trol b utton > Service
& checks > Service intervals. Tu rn the control
knob downward to
Reset oil change interval and
press the cont rol knob.
(D Note
- Only reset the oil change indicato r if the oil
was changed .
- Fo llow ing the service i nte rva ls is critical to
maintai ning the service life an d va lue of
your ve hicle, especia lly the engine. Even if
the m ileage on the vehicle is low, do not ex­
ceed the time for the next service.
- Ca lculating the t ime to the next oi l change
i s interrupted when the ve hicle battery is
d iscon nected¢
page 239 .
210

a,
a,
..... N r-. N ..... 0 a, OJ ..
Maximum (permissible )
inflat ion pressure
means the maximum cold infla­
tion pressure to wh ich a t ire may
be inflated. Also called "maxi­
mum inflation pressure ."
Normal occupant weight
means 150 lbs . (68 kilograms)
times the number of occupants
seated in the veh icle up to the to­
tal seating capacity of your vehi­
c le .
Occupant distribution
means distribution of occupants
in a vehicle.
Oute r diameter
means the overall diameter of an
inflated new tire .
Overall width
means the linear distance be­
tween the exteriors of the side­
walls of an inflated tire, including
elevations due to labeling, deco­
rations, or protective bands or
ribs.
Ply
means a layer of rubber-coated
parallel cords.
Wheels
Production options weight
means the combined weight of
those installed regular production
options weighing over 5 lbs. (2.3
kg) in excess of those standard
items which they replace, not pre­
viously considered in curb weight
or accessory weight, including
heavy duty brakes, ride levelers,
roof rack, heavy duty battery, and
special trim .
Radial ply tire
means a pneumatic tire in which
the ply cords that extend to the
beads are laid at substantially 90
degrees to the centerline of the
tread.
Recommended inflation
pressure
see ¢ page 214, Cold tire infla­
tion pressure.
Reinforced tire
means a tire designed to operate
at higher loads and at higher in ­
flation pressures than the corre­
sponding standard tire. Rein­
forced tires may be identified as
"X L", "xl", "EXTRA LOAD", or "RF"
on the sidewall. ..,
215

co
co
.... N
" N .... 0
00
\.J ' avoid scratches, move the scraper only in
one direction and not back and forth.
- Never remove snow or ice from door win­
dows and mirrors using warm or hot water
because this could cause cracks to form.
- To avoid damage to the rear window de­
fogger, do not apply any stickers on the
heating wires on the inside of the window.
- Decorative part .s/trim
- Never use chrome care or cleaning prod-
ucts .
-Paint
- To reduce the risk of scratches, the vehicle
must be free of dirt and dust before pol­
ishing or waxing.
- To prevent paint damage, do not polish or
wax the vehicle in direct sunlight .
- To reduce the risk of paint damage, do not
polish away rust spots .
- Remove cosmetics and sunscreen immedi­
ately- these could damage the paint.
-Displays
-To avoid scratches, do not use dry cleaning
methods on displays.
-Controls
- Make sure that no fluids enter the con-
trols, because this could cause damage.
- Safety belts
- Do not remove the safety belts to clean
them.
- Never clean safety belts or their compo­
nents chemically or with corrosive fluids
or solvents and never allow sharp objects
to come into contact with the safety belts.
This could cause damage to the belt web­
bing.
- If there is damage to the webbing, the
connections, the retractors or the buckles,
have them replaced by an authorized Audi
dealer or authorized Audi Service Facility.
- Textiles/artificial leather/ Alcantara
- Never treat artificial leather/ Alcantara
with leather care products, solvents, floor
polish, shoe polish, spot remove or similar
products .
- Have a specialist remove stubborn stains
to prevent damage.
Care and cleaning
-Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the
seat.
- Objects with sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
- Open hook and loop fasteners, for exam­
ple on clothing, can damage seat covers.
Make sure hook and loop fasteners are
closed.
- Natural leather
- Never treat leather with solvents, floor
polish, shoe polish, spot remover or simi­
lar products.
- Objects with sharp edges, such as zippers or rivets on clothing or belts, can cause
damage to the surface.
- Never use steam cleaners, brushes, hard
sponges, etc . when cleaning.
- Do not turn on the seat heating* to dry the
seat.
- To help prevent the leather from fading,
do not leave the vehicle in direct sunlight
for long periods of time. If leaving the ve­
hicle parked for long periods of time, you
should cover the leather to protect it from
direct sunlight.
(D Tips
-Insects are easier to remove from paint that
has been freshly waxed.
- Regular waxing can prevent rust spots from
forming.
Placing your vehicle out
of service
If you would like to take your vehicle out of serv­
ice for a longer period of time, contact an author­
ized Audi dealer or authorized Audi Service Facili­
ty. They will advise you of important measures,
such as corrosion protection, service and storage procedures . Also follow the information about
the vehicle battery~
page 207.
239