2017 AUDI A7 engine

Service Faci lity i f th e battery charge level is too
l ow .
(•) Low battery charge : Battery will be charged
while driving
The start ing ability may be impaired .
If th is message turns
off after a litt le while, the
ve hicle battery charged enough wh ile driving.
If the message does not turn
off, h ave an a uthor ­
ized A udi dealer o r autho rized Audi Serv ice Fac ili­
ty repa ir th e malfunct ion.
~ Engine stop while driving
• Engine stopped: No power steering and
brake support .
There is a malfunction in the eng ine or in the fuel
supp ly system.
M ore fo rce is needed to steer and brake the mov ­
ing ve hicle w hen t he engine is stoppe d. If the ve­
hi cle is rol ling, try to b ring it to a stop
off to the
side from moving traffic. See an aut ho rized Aud i
dealer or aut ho riz ed Aud i Serv ic e Faci lity fo r as­
sis tanc e.
A WARNING
-
If the e ng in e stops while d riving, yo u will
nee d to use more force to brak e the vehicle.
T hi s i ncrease s the r is k of an a ccid ent. Th ere
w ill still be power s teerin g if th e i gnit ion is
switched on w hil e the vehicle is rolling an d
there is sufficient battery c har ge. Othe rw ise,
you must use greate r force when steer ing.
~ Engine oil pressure
• Turn off engine and check oil level
Stop the eng ine and do not continue driving .
Chec k the engine oil leve l
Q page 204.
-If the engi ne oil leve l is to o low, add engine oil
Qpoge 204. O nl y con tinue driv ing once the in­
dicato r light turns
off.
co ~ - If the engi ne oil leve l is co rr ec t an d t he i ndic a-
~ to r lig ht st ill tur ns on, tur n the eng ine off and N
8 do not con tinue driving . See an auth o rized Aud i 00 \.J ' Instruments and ind icator lights
dea ler o r auth orized Audi Service Facili ty fo r as ­
sistance .
(D Tips
The oil pres sure w arnin g is no t an oil leve l in­
d ic ator. Always check the oil level regula rly.
't::r;. Engine oil level
• Please add oil immediately.
Add o il imme diate ly Qpoge 202.
Ill Add oil max. x qt (l). You may continue driv­
ing
Add t he d isplayed amount of oil immediately
Q page202.
~- Steering lock
• Do not drive vehicle: Steering defective
There is a ma lfunction in the e lectron ic steering
l ock . You cannot tur n the ign ition on .
Do
not tow yo ur vehicle because it cannot be
stee red. See an a uthorized Audi dea ler or author­
ized Audi Service Facility for ass istance.
!II Steering lock : System fault Please contact
dealer
T he re is a m alfu n ct ion in the e le ctro nic st eering
l ock .
Dr ive to a n au thori zed A udi dealer or au tho riz ed
A udi Se rvice Faci lity i mmed iate ly to h ave the
m alfu nction correc te d .
A WARNING
-
Do not tow yo ur vehicle when there is a m al­
f u nction in t he electron ic steer ing lock - t his
i nc reases t he risk of an acc ident.
© -Engine start system
• Engine start system fault . Please contact
dealer
Do not switch the ignition off because you may
not be able to switch it on again . .,.
15

Instruments and indicator lights
Drive to an autho rized Aud i dea ler or a uth orized
Aud i Service Facility immediately to have t he
malfunct ion corrected .
Ill Engine start sy stem fault . Plea se contact
dealer
There is a malfunction in the eng ine start ing sys­
tem.
Dr ive to an authorized Aud i deale r or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
0 Air suspension
• Air su spen sion : Sy stem fault Driving slowly
at maximum 35 mph is pos sible.
There is a malfunction that can result i n restrict­
ed driving stabili ty.
Drive to an autho rized Aud i dea ler or authorized
Aud i Serv ice Facility immediately at a maximum
speed of 3S mph (60 km/ h) to have the ma lf u nc­
tion cor rec ted .
• Air suspension : Service mode . Vehicle can
only be moved with restrictions
Carefully drive to your author iz ed Audi dealer or
author ized Audi Service Facility immed iate ly to
have the serv ice mode deactivated.
rl Air suspension : System fault
T here is a system malfunct io n that ca n result in
restricted driving stability o r reduced ground
clearance .
Dr ive to an a uth o rized Aud i de aler or auth o rized
Aud i Serv ice Facility immediately to have t he
malfunction corrected .
rl Air sus pension : Vehicle is too low. Ground
clearance limited
The ground clearance is very low due to a system malfunct io n. Wa it until the air suspens ion sys­
tem has restored norma l grou nd clearance. Oth­
erw ise, condi tions such as an uneven road s urfa ce
can lead to vehicle damage.
16
Lt Brake booster
d Brake servo : limited functionality . You can
continue driving . Conta ct work shop
There is a ma lfunction in the brake booster. The
brake booste r is ava ilab le, but its effectiveness is
r educed. Bra kin g behavior may be different from
h ow it norm ally f un cti ons and the br ake peda l
may vibrate .
D rive to an au thorized A udi dealer or autho rized
Audi Se rvice Fa cil ity immed iate ly to have the
malfunction cor rec ted .
;;,/!:; Electronic Stabilization Control (ESC)
If the bl ind icator light blinks while driving, the
ESC or ASR (Anti-Slip Regulation) is active ly regu­
l ating .
I f the
bl ind ic a tor light turns on, the system has
swi tched t he ESC off. In t his case, yo u can switch
the ignition off and then on to switch the ESC on again. The indicator light t urns off when the sys ­
tem is functioning fully .
I f the
II ind icator light turns on, ESC was
switched off using the
I~ O FFI button
¢ page 120 .
Stabilization control (ESC / ABS) malfun ction!
See owner's manual
I f the GJ ind icator light and t he A BS i ndica to r
li gh t
rJ]J (U SA mode ls) I riJ (C an ada models)
tu rn o n an d this message appears, there is a mal­
funct ion in the ABS system or e lectronic differen ­
tia l lock. This also causes the ESC to malfunction.
The brakes still function with their normal power, but ABS is not active.
Drive to an authorized A udi dealer or au thorized
Audi Se rvice Facility immediate ly to have the
malfunction corrected.
A WARNING
If the 1111 (USA models) • (Canada mod ­
e ls) brake system ind icator light turns on to­
gethe r with the ABS and ESC ind icator lights,
the ABS a nd ESC regulating fu nction may
h ave mal func tioned. Funct io ns that stab ilize

co
co
.... N
" N .... 0
00
\.J ' the vehicle are no longer available. This could cause the vehicle to swerve, which increases
the risk that the vehicle will slide. Drive care­
fully to the nearest authorized Audi dealer or authorized Audi Service Fac ility and have the
ma lfunction corrected.
(D Tips
For additional information on ESC and ABS,
see
r:::> page 120 .
ii !i.' Safety systems
The II (USA models) / m (Canada models) indi­
cator l ight monitors the safety systems.
If the
II (USA models)/ m (Canada models) in­
d icator light turns on or blinks, there is a mal ­
function in a safety system such as the airbag or
be lt tensioner system .
Drive to an authori zed Audi dealer or authorized
Aud i Service Facility immediately to have the
malfunct ion corrected .
_& WARNING
Have the malfunct ion in the safety systems
inspected immediately . Otherwise, there is a
r isk that the systems may not activate during
a collision, which increases the risk of serious
injury or death.
{0 } Brake pads
EIJ Brake pads!
The brake pads are worn.
Drive to an authorized Aud i dealer or authorized
Aud i Service Facility immediately to have the
b rake pads checked.
Applies to: USA models
The EIJ ind icator light turns on together w ith the
11111 i ndicator light
EPC Engine control (gasoline engine)
If the 13:a indicator light turns on if there is a
malfunction in the engine control.
Instruments and indicator lights
Drive slowly to an authorized Audi dea ler or au­
thorized Audi Service Facility to have the engine
checked.
W Engine control (diesel engine)
The engine is preheating if the II indicator light
turns on when the ignition is switched on .
If the indicator light does not turn on or blinks
while driving, there is an engine control malfunc­
t ion.
Immediate ly drive s low ly to an authorized Audi
dealer or authorized Audi Service Facility to have
the malfunction corrected.
C Malfunction indicator lamp (MIL)
The malfunction indicator lamp (MIL) is part of
the On Board Diagnostic system (OBD II) . The
¢4 c;ymbol turns on when the ignition is sw itched
on and turns off aga in once the engine is started
and running at a steady idle speed. This indicates
that the MIL is f unct ion ing correctly.
The indicator light turns on if there is a malfunc­
t ion in the engine electronics . See an authorized
Audi dealer or authorized Audi Service Fac ility to
have the malfunction corrected. Fo r additional
information, seer:>
page 25.
The ind icator light can also turn on if the fuel fill­
er cap is not closed correctly
r:::>page 193.
_r~ Diesel particulate filter
Applies to: vehicles with diesel engine and diesel particulate
filter
II Particulate filter: System fault See owner's
manual
The diesel particulate filter requires regenera­
t ion . To support the filter 's self -clean ing func ­
t ion:
Drive for approximately 15 minutes at 37 mph
(60 km/h) or above in the S selector lever posi­
t ion . Keep the engine speed around 2,000 RPM .
The temperature increase that will result from
t hi s can burn off the soot in the fi lter. The indica­
tor light wi ll tu rn off when the cleaning has com-
pleted successfully. .,..
17

Instruments and indicator lights
If the i ndicator lig ht does not tu rn of f, drive im ­
mediately to an a utho rized Audi dea le r or author­
ized A ud i Service Fac ility to have the malfunction
corrected.
A WARNING
Always ada pt yo ur speed to the cu rrent
weathe r, road and t raffic conditi ons. You
should never disob ey traffic laws in orde r to
follow drivi ng r ecomme nda tions .
@ Tips
For add it iona l information on the diese l par­
tic ulate fi lter, se e
¢page 199.
!?'i Engine speed limitation
Applies to: vehicles with engine speed limitation
Ill Maximum engine speed: XXXX rpm
The engine speed is automatica lly lim ited to the
speed d isplayed in the instrument cluster. T his
p rotects the e ng ine from overheating .
The engine speed lim itation deactivates once the
engine is no longer in the critical temperature
range and you have released the acce le rato r ped­
al once .
I f the engine speed lim itation was activated by
an eng ine contro l ma lf u nction,
the @B indicator
light also t urn s on. Make su re that the speed
does not go above t he speed d is p layed . Drive to
a n author ized A udi dealer or au thor ized A udi
Serv ice Facili ty im medi ately to have t he m alfunc­
tion cor rec ted.
(D Tips
Applies to: Sand RS models
The e ngi ne sp eed is lim it e d whe n the eng ine
is cold -the full engine o utpu t is not av ail a­
ble. When the engine is at operating temper­
ature, the re d area in th e tachometer moves
to a highe r RPM ra nge.
_ ..., Engine oil sensor
• Oil level sensor: system fault!
18
The sensor to check the en gine o il level has
failed. Drive to an authorized A udi dealer or au­
t h orized Aud i Serv ice Facility immediately to have
the malfunct ion corrected.
f Engine warm -up request
n Please warm up engine
F u el has entered t he engine oil, eithe r from low
outside temperatures or frequent sho rt d rives.
D rive until the eng ine is wa rm so that the f uel in
the e ngine o il w ill evaporate . Avoid hig h eng ine
speeds, f ull accelerating a nd heavy engine loads
wh en doi ng this .
5) Tank system
Ii] Please refuel
If the indicato r light turns on for the first time
and t he message appea rs, the re are abou t 2.6
gallons ( 10 li ters) of f uel left in t he tank .
Ii] Fuel tank system malfunction! Please con­
tact dealer
There is a ma lf u nction in t he f uel tank system.
Dr ive to an au thor ized A udi d ealer or au thorize d
Audi Se rvice Facility immediate ly to have the
malfunction cor rected.
(D Tips
'
For add it ion al in format ion on ref ueli ng, see
¢ pag e 193 .
~ Washer fluid level
f"j i>lease add washer fluid
Fill the w ashe r flui d fo r th e win dsh ie ld was her
system and the he adlight washer sys tem* when
t h e ignit io n is switched off¢
page 209 .
• Windshield wipers
m Windshield wipe r: system fault!
There is a m alfu ncti on with the win dshi eld wip -
ers . ..,.

co
co
.... N
" N .... 0
00
<.,;) 'SI"
Driver information
system
Overview
Fig . 4 Dr iver informa tion system in t he inst rum ent clus ter
Fig . S Ins trum ent cl uster: examp le in formation line
The information in the driver information system
is shown in @ tabs @
c::> fig. 4. The following
content is possible depending on vehicle equip­
ment:
Driver in forma tion system
® ®
First tab Vehicle functions:
On-boa rd computer
c::> page22
Efficiency program*
c::>page23
Digital speedometer
Cruise control system*
c::> page 85
Adaptive cruise control* and braking
guard*
c::> page 88
Active lane ass ist*
c::> page 96
Boost, shifting and engine oil tern-
perature indicators*
c::> page 8 7
Lap timer*
c::> page 8 7
Reduced display
Second Indicator lights and messages
tab Warning when a door, the hood o r
the rear lid is not closed
Service interval display
c::> page 209
Speed warning system *
c::> page 85
Third tab Night vision ass istant*
c::> page 102
Fourth Audio/Video
tab
Fi fth tab Telephone*
Sixth tab Navigation*
The second and third tabs are only visible if at least one indicator light or message is shown or if
that system is switched on .
The status line © is located in the bottom part of
the display
c::> fig . 4. It displays the exterior tem­
perature, time, selector lever position, tripod­
ometer and odometer .
For some vehicle functions, you can access the
trip information from the temporary memory
c::> page 23 in line (D c::> fig . 5.
21

Driver i nf orm ati on sy stem
_&. WARNING
Do not assume the roads are free of ice based
on the outs ide temperature display. Be aware
that there may be ice on roads even when the
outside temperature is around 41 °F (+5 °C)
and that ice can increase the risk of accide nts .
{D) Tips
-You can select the units used for tempera­
ture, speed and othe r measurements in the
Infotainment system .
- If your vehicle is stationary or if you are driv­
i ng at very low speeds, the temperature dis­
played may be s light ly higher than the ac­
tual tempe ra ture o utside d ue to the heat ra­
d ia ti ng from the engine.
- Fo r informat ion on the a udio/video and nav­
i gat ion * func tions, refer to the separa te In­
fotainment system owner's manua l.
Operation
The driver information system is operated using
the buttons on the multifunction steering wheel.
Fig. 6 Mult ifunct io n steering whee l: operating the driver
info rma tion system
Fig . 7 Instr umen t cluster: opening the vehicle functions
menu
22
Operating
.,. Switch the ignit ion on .
.,. To switch between the tabs, press the rocker
switch © to the left or right¢
fig. 6.
.,. To access additiona l information below or
above, tu rn the thumbwheel @down or up.
.,. To confirm a selection, press the thumbwheel
@.
.,. To open the submenu for an act ive tab, press
the button lil@.
.,. To sele ct a func tion p rogrammed to a steer ing
wheel b utton*, press the butto n@ .
Opening the Vehicle funct ions
.,. Select the first tab with the rocker sw itch ©­
.,. Press the
[i] button @. The V ehi cle function s
menu is disp layed ¢ fig. 7.
.,. To sele ct a menu item, turn and press the
t humbwhee l@ .
Resetting values to zero
.,. In the Vehicle fun ct ion s menu, select On­
boa rd compu ter
or Efficien cy program .
.,. You can now se lect between the long-term
memory and short- term memory .
.,. To reset the va lues in a memo ry, press and hold
the th umbwheel @for one second.
Assigning a function to a programmable
steering wheel button*
.,. Select the I CAR ! funct ion button > ( Car )*Sy s­
tem s
control button > Vehicle setting s > Steer­
ing wheel button prog ramming.
The las t function selected d isp lays when you
swi tch the ign ition on .
On-board computer
Fig. 8 Instrument cluste r: fuel consumption display

co
co
.... N
" N .... 0
00
<.,;) 'SI"
You can call up the following information in the
on-board computer:
- Date
- Driving time from the short-term memory
- Average consumpt ion from the short-term
memory
- Average speed from the short-term memory
- Distance driven from the short-term memory
- Current fuel consumption
- Short-term memory overview
- Long-term memory overview
The short-term memory co llects driving informa­
tion from the t ime the ignition is switched on un­
til it is switched off.
If you continue driv ing with­
in two hours af ter switching the ignition off, the
new values are included when calculat ing the cur­
rent trip information .
Unlike the short-term memory, the long-term
memory is not erased automat ically. Yo u can se­
l ect the time period for evaluating trip informa­
tion yourself.
F or some veh icle functions, you can access the
driving info rmation from the short-term memory
in the
line @c:>page21, fig. 5.
Fuel consumption
The current fue l consumption can be shown us­
ing a bar g raph c:>
fig. 8. The average consump­
tion stored in the short-term memory is also dis­
p la yed. If the bar is green, your vehicle is saving
fuel through one of the following functions:
-Re cuperation : electrical ene rgy can be stored in
the vehicle battery when the vehicle is coasting or driving downhill. The bar will move toward
0.
-Cylinder on demand system*: the engine auto­
matically switches four cylinders off when low­
er power output is required and other condi­
tions are met . This change is not noticeable to
the passengers.
@ Tips
The date, time of day and time and date for­
mat can be set in the Infotainment system
qpage24 .
Driver in forma tion system
Efficiency program
Applies to: vehicles with efficiency prog ram
Fi g. 9 Instrument cluster: other equ ipment
Fig. 10 Instrument cluster: economy t ip
T he eff iciency program can help you to use less
fuel.
It shows other consumers that are using
f uel and economy tips give advice on how to dr ive
efficiently. The efficiency program receives dis­
tance and consumption data from the on-board
computer.
T o display the efficien cy program, open the
Vehi­
cle functions
menu and select the Efficiency pro·
gram
menu item.
Other consumers
T he Energy consumers view lists other equip­
ment that is currently affecting fuel cons ump­
tion. The display shows up to three o ther equ ip­
ment items @c:>
fig. 9. The equipment using the
most power is listed first. If more than three
items using power are switched on, the equip­
ment that is current ly using the most power is
displayed.
A gauge @also shows the current tota l con­
sumption of all other consumers.
23

co
co
.... N
" N .... 0
00
<.,;) 'SI"
Adjusting the height
The height of the display can be adjusted to the
individua l driver .
.. Make s ure yo u are seated cor rect ly
<=> page 130.
.. Turn the knob~ to adjust the displ ay .
Settings in the Infotainment system
.. Se lect: the ICA RI function button > (Car )* Sys ­
tems
control b utton > Driver assistance >
Head-up display > Head-up di splay contents or
Display brightne ss .
Display content
In the Infotainment system, yo u can specify
which informa tion should be displayed: For ex­
ample, th is can incl ude navigation informat ion*,
Adap tive cr uise con trol* or nig ht vision ass ist *.
T he display of certa in i nformation and some of
the red indicator lig hts cannot be h idden in the
I nfotainmen t system .
Display brightness
You can ad just the display brightness in the Info­
tainmen t system. The display brig htness decreas­
es automatically as the amount of light decreas­
es . The backgro und bright ness is adjusted with
the ins trumen t illumina tion <=:>
pag e 43.
(D Note
To prevent scratches on t he g lass cove ring the
head-up d is p lay, do not place any o bjects in
t h e projection o pening.
(D Tips
-Su nglasses w it h polar izat ion fi lt e rs a nd u n­
favo rab le lighting conditions can have a
negative effect o n th e di splay .
- An optim um display depe nds on the s eat
pos ition and th e height adjus tme nt of th e
h ead -up display .
- A sp ecia l wi ndshield is needed for th e head ­
u p d isplay f unction.
- Fo r info rmat ion o n cleaning, refer to
c::> ta ­
ble on page 237.
Driver in forma tion system
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL)
The Ma lfunction I ndicator Lamp (M IL) ¢• in the
inst rument cluste r is pa rt of the On-Board D iag­
nostic (OBD
II) system .
T he w arnin g/i ndic ator lig ht ill uminates w hen the
ignition is sw itche d on an d goes out after the en­
gine starts and the idle has stab ilized. This indi­
cates that the MIL is wor king p roperly.
If the light does not go out a fter the eng ine is
started, or illum inates w hile you are drivin g, a
malfu nction may ex ist in t he engine system . If
t h e lig ht ill uminates, the catalytic converter
cou ld be damaged.
Cont inue d riving
with reduced power (avoiding
s u stai ned high speeds and/o r rap id accelera­
t ions) and have the condition corrected. Contact
yo ur aut hori zed Aud i deale r.
If the light illum inates, the elect ronic speed lim­
ite r may also be ma lf u nct io ni ng. For more infor­
mation
c::> page 26, E lectronic speed limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
<=> page 193 .
On-Board Diagnostics
Fig. 14 Location of Data Link Co nnector (D LC)
On- Boar d Dia gno sti cs m onitors the components
of your emissio n con trol system . Each monitore d
com ponent in your engine system has been as­
s igned a code . In case of a malfunction, the com­
ponent will be ident ified and the fault sto red as a
code in the contro l modu le memory.
II>
25