2017 AUDI A6 ESP

co
co
.... N
" N .... 0 0 <..:l - ~Pullon the tether strap hook so that the spring
catch of the hook engages.
~ Tighten the tether strap firmly fo llow ing the
child restraint manufacturer's instructions.
Releasing the tether strap
~ Loosen the tension following the child restraint
manufacturer's instructions.
~ Depress the spring catch on the hook and re­
lease it from the anchorage .
(1;) Note
If you leave the chi ld restraint with the tether
strap firmly installed for several days, this
could leave a mark on the upholstery on the
seat cushion and backrest in the area where
the tether strap was installed . The upholstery
would also be permanently stretched around
the tether strap . This applies especially to
leather seats.
Using tether straps on rearward-facing
child restraints
Current ly, few rear-facing chi ld restraint systems
come with a tether. Please read and heed the
child restraint system manufacturer's instruc­
tions carefully to determine how to properly in­
stall the tether .
A WARNING
A child in a rearward-facing child safety seat
installed on the front passenge r seat w ill be
ser iously injured and can be killed if the front
airbag inflates - even w ith an Advanced A irbag
System.
- T he inflating airbag will hit the child safety
seat or infant carrier with great force and
will smash the chi ld safety seat and child
against the backrest, center armrest, or
door.
- If you must install a rearward facing child
safety seat on the front passenger seat be­
cause of exceptiona l circumstances and the
PASSENGER AIR BAG OFF light does not
come on and stay on, immed iately install
the rear-facing child safety seat in a rear
Child safety
seating position and have the airbag system
inspected by your Audi dealer.
Additional information
Sources of information about child
restraints and their use
There are a number of sources of additional in­
formation about child restraint selection, instal­
lation and use :
N HT SA advises that the best ch ild safety seat is
the one that fits your child and fits in your vehi­
cle, and that you wi ll use correct ly and consis ­
tent ly.
T ry before you buy!
U.S National Highway Traffic Safety Administra­
tion
T el. : 1-888 -327-4236 ( TTY: 1-800-424-9153)
http:/ /www.nhtsa.gov
http:/ /www.sa fercar.gov
National SAFE KIDS Campaign
T el.: (202) 662-0600
http:/ /www.safekids .org
Safety BeltSafe U.S.A
Tel.: (800) 745-SAFE (En glish)
T el.: (800) 747-SANO (Spanish)
http:/ /www.carseat.org
Transport Canada Information Centre
T el.: 1-800-333-0371 o r call 1-613-998-8616 if
you are in the Ottawa area
http://www.tc.gc.ca/ eng/roadsafety/menu . htm
Audi Customer Relations
Tel.: (800) 822-2834
189

co
co
.... N
" N .... 0 0 <..:l ' fill up at busy gas stations where the seasonal
adjustment is more likely to be made in time .
(D Note
-Methanol f uels which do not mee t these re­
quirements may ca use corrosion and dam­
age to plastic and rubber components in the
fuel system.
- Do not use fuels that fai l to meet the speci­
fied criteria in this chapter.
- If you are unable to determine whether or not a particular fuel blend meets the speci­
fications, ask your service station or its fuel
supplier.
- Do not use fuel for which the contents can­
not be identif ied.
- Fuel system damage and performance prob­
lems resulting from the use of fue ls differ­
ent from those specified are not the respon­
s ibility of Audi and are not covered under
the New Veh icle or the Emiss ion Control
System Wa rrant ies.
- If you experience a loss of fue l economy or
driveability and performance problems due
to the use of one of these fuel b lends, we
recommend that you switch to unblended
fuel.
Gasoline additives
A ma jo r concern among many auto manufactur ­
e rs is carbon deposit build-up caused by the type
of gasoline you use.
A lthough gasoline grades d iffer from one manu ­
facturer to ano ther, they have certain things in
common . All gasoline grades contain substances
that can cause deposits to collect on v ita l eng ine
parts, such as fuel injectors and intake valves. Al­
though most gasoline brands include additives to
keep engine and fuel systems clean, they are not
equally effective.
Audi recommends using TOP TIER Detergent Gas­
oline. For more informat ion on TOP TIER Deter­
gent Gasoline, please go to the official website (www .toptiergas .com) .
Check ing and Filling
After an extended period of using inadeq uate
fuels, carbon deposit bui ld-ups can rob your en­
gine of peak performance.
(D Note
Damage or ma lf u nction due to poor fuel qual ­
ity is not covered by the A udi New Vehicle
Limited Warranty .
Diesel fuel
Applies to: vehicles with diesel engine
Always use ULSD (Ultra Low Sulfur Diesel) No. 2 .
The ULSD No . 2 meets the ASTM 0975.
Diesel fuel w it h concentrations of b iod iesel h igh­
er than 5 % such as Bl 1, B20 or BlOO are strict ly
prohibited .
Se rvice station fuel p umps are labe led with the
correct f uel info rmation for e asy recog nition by
the user.
If the d iesel fue l pump is not labeled
ask the station operator what fuel is being dis­
pensed before fil ling up your vehicle .
UL SD No . 2 m ay not be available ou tside the USA
and Canada . Be sure to check befo re t raveling to
other countries .
UL SD No . 2 can become thic ke r i n ve ry cold tem­
peratures, and th is can imp air the engine's s tart ­
ing and running. Depend ing on the sea son, gas
stations provide ULSD No . 2 that flows better in
cold temperatures so that you can continue oper ­
at ing your vehicle as usual.
@ Note
- Your vehicle's diese l engine was designed
soley for use with ULSD No . 2 . Therefore,
neve r use gasoline, heating oil, other fuels
or flow improvers. These contain substances
that will severely damage the fuel system
and the engine . Such damage will not be
cove red by your New Vehicle Limited War­
r a nty.
- If you put a ny amo unt of incorrect fuel in
the fuel tank, do not sta rt the eng ine under
any circumstances. Imme diately contact the
nea res t a uthor ized Audi dealer or author­
ized Aud i Serv ice Facility fo r ass istance .
191

Checking and Filling
& WARNING
AdBlue can irritate the skin, eyes and respira­tory system. If there is contact with the fluid,
flush immediately with plenty of water . Con­
sult a physician if necessary.
(D Note
- Only use Ad Blue that conforms to the
standard ISO 22241 -1. Do not mix any addi ­
tives with the Ad Blue and do not dilute it
with water.
- Do not add Ad Blue to the diesel tank or add diesel fuel to the Ad Blue tank. Do not start
the engine under any circumstances if the
wrong fuel is filled in the tank. There is a
risk of damaging the fuel tank system and
the engine. See an authorized Audi dealer or
authorized Audi Service Facility for assis­
tance.
- AdBlue attacks surfaces such as painted ve­
hicle components, plastic and carpet. Re­
move the fluid as quickly as possible with a
damp cloth and plenty of cold water. If the
Ad Blue has already crystallized, use warm
water and a sponge . AdBlue residue that is
not removed will crystallize and can damage
the affected surface.
- Do not store refill bottles or canisters per ­
manently in the vehicle. If the container
leaks, the escaping AdBlue could damage
the vehicle interior.
- Do not allow AdBlue to come into contact
with clothing. If there is contact with the
fluid , flush immediately with plenty of
wa­
ter.
(j) Tips
Follow the Ad Blue manufacturer 's instruc­
tions for use and storage.
Refilling AdBlue using a bottle
Applies to: vehicles with selective catalytic reduction
... Remove the cap from the refill bottle ¢.&. in
Filling AdBlue on page 196,
c::> (D in Filling
AdBlue on page 196.
196
... Position the bottle on the filler tube and turn
the bottle clockwise until it stops turning.
... Press lightly against the bottom of the bottle
to empty it . Continue pressing the bottom of
the bottle until it is empty or until fluid stops
flowing into the tank .
... Remove the bottle and seal the filler neck
c::> page 197, Completing AdBlue refill.
d) Note
Only use refill bottles that are approved for
your vehicle. Using other systems can cause AdBlue to leak.
(D Tips
- You can obtain refill bottles from an author­
ized Audi dealer or authorized Audi Service
Facility.
- A permitted refill bottle contains approxi­
mately 0.5 gallon (1.9 liters) of AdBlue.
Refilling AdBlue using a canister
Applies to: vehicles with selective catalytic reduction
®
+®
Fig. 179 Canister w ith attachable hose
... Remove the cover from the refill canister c::> .&.
in Filling AdBlue on page 196 , c::>(D in Filling
AdBlue on page 196 .
.,. Secure the end of the hose the canister @by turning the hose to the right.
.,. Remove the cap @from the other end of the
hose @.
... Position the end of the hose @on the filler
neck in the vehicle and turn the hose to the
right to tighten it .
... Lift the canister up and then tip it . Continue
holding the canister in a tipped position until it
1J,,

co
co
.... N
" N .... 0 0 <..:l 'SI'
The coolant leve l is monitored through the. in­
dicator light
c::> poge 14. However, we do recom­
mend occasionally check ing the coo lant level
manually.
If you m ust add coolant, use a m ixture o f water
and coolant additive . M ixing the coolant additive
w ith d istilled water is recommended.
Coolant additive
The coolan t addi tive is made of ant i-freez ing and
corrosion protection agents. Only use the fo llow­
i n g coo lant additives . These additives may be
mixed wit h each other .
Coolant additive Specification
Gl3 TL774J
Gl2++ TL 774 G
The amount of coo lant add itive that needs to be
mixed with water depends on the climate where
the veh icle will be ope rated. If the coolant addi­
tive percentage is too low, the cool ant can freeze
and damage the engine.
Coolant Freeze protec-
additive tion
Warm regions min . 40% m
in. -13 ° F
max. 45% (-25 °C)
Cold regions min . 50% max . -40 °F
max . 55% (-40 °C)
(D Note
-
Befo re the start of winter, have your author­
i zed Audi dealer or author ized Audi Se rvice
Facility check if the coolant additive in yo ur
vehicle ma tches the percen tage approp riate
fo r th e climate. This is especially import ant
whe n driving in co lder climates .
-If the approp ria te coolant addi tive is no t
available in an emergency, do no t ad d any
other additive. You co uld damage the en­
gine. If this happens, only use wate r and re­
store the correct mixture ratio with the
spec ified coolant additive as soon as possi­
ble.
- Only refill with new coo lant .
- Radiator sealant must not be mixed with
the coo lant .
Checking and Filling
Adding coolant
Fig. 184 En g in e compa rtment : coo lant expa nsion ta nk
cove r
Observe the safety prec autions c::> A in Working
in the engine comportmen t on page 198.
Checking the engine coolant level
Park the vehicle on a level surface.
.,. Switch t he ignit ion off.
.,. Read the coolant level on the coolant expansion
tank
c::> page 201, fig . 182. The coolant level
must be between the MIN and MAX mark ings
when the engine in cold. When the eng ine is
warm it can be slightly above the MAX marki ng.
Adding coolant
Requirement: there must be a residua l amount of
coolant in the expansion tank
c::> (D .
.,. Let the eng ine cool down .
.,. Place a cloth over the coolant expansion tank
cap and unscrew the cap counterclockw ise
c::> .&_ .
.,. Add coo lant m ixed in the cor rect rat io
c::> page 204 u p to the MAX mark ing.
.,. Ma ke sure that the f luid level remains stab le.
Add mo re coolant if necessary.
.,. Close the cap sec urely.
Coo la nt loss usually i ndicates there is a lea k. Im­
med iate ly drive you r ve hicle to a n author ized
Audi dealer or authorized A udi Se rvice Faci lity
and have the cooling system inspected. If the
cooling system is not leak ing, a loss can come
from the coolant boiling through overheat ing
and being pushed out of the cooling system.
205

Check ing and F illing
"' Clamp the charger terminal clamps to the jump
start pins according to the instruct ions. (pin un ­
der the red cover = "positive", pin with hexago ­
nal head = "negative").
"' Insert the power cable for the charging device
into the socket and switch the device on .
"' At the end of the charging process, switch the
charge r off and pull the power cab le out of the
socket.
"' Remove the c ha rge r termi nal clamps.
"' Close the red cover on the posi tive te rm inal.
"' Close the hood
¢ page 200.
A WARNING
- A highly explosive mixture of gases can form
when charging batter ies. On ly charge the
vehicle battery in well-vent ilated areas.
- A drained battery can freeze at tempera­
tures a round 32 °F (0 °C). A frozen or
thawed veh icle battery must not be charged
and must not be used anymore . The batte ry
hous ing can crac k an d battery acid can leak
o ut if ice fo rms, wh ic h increases the r is k of
an exp losion and ch emical burns. Contact an
authoriz e d Au di dea ler o r aut ho riz e d Aud i
Service Facility for mo re inform ation .
- Do no t conne ct o r dis co nne ct the c hargi ng
cable while charg ing because th is increases
the risk of an exp losion .
(D Tips
-Only ch arge the vehicle battery through the
c on nection s in t he e ng ine comp artmen t.
- Read a ll of the manufacture r's instruc tions
f or the charger befo re charg ing the ve hicle
b attery .
208
Windshield washer
system
Fi g. 187 En gin e compar tm en t: was her flui d rese rvoir cap
.., N
-N ~ a, m
The w indshield washer reservoir O con tains the
cleaning so lution for the windshield and the
headlight washer system *
q page 201, fig. 182.
The reservoir capacity can be found in
¢ page 257.
To reduce the risk of lime scale deposits on the
spray no zzles, use clean water with low amo unts
of calcium. Always add window cleaner to the wa­
ter. When the ou tside temperatures are cold , an
anti -freezing agent shou ld be added to the water
so tha t it does not freeze .
(D Note
-The concentration of ant i-freez ing agent
must be adjusted to the ve hicle operat ing
condi tions i n the respective cl imate . A con­
c entration that is too h igh can lead to vehi­
cl e damage.
- N ever add radia to r anti-free ze or other addi­
t ives to the washer fluid.
- Do not use a glass cleaner t hat contains
pai nt so lvents, because th is could damage
t h e pain t.
Service interval display
The service in terval display detects when your ve­
hicle is due for service.
The serv ice interval d isplay wo rks in two stages:
-Inspection or oil change rem inder: afte r a cer-
tain dis tance drive n, a message appears in the ..,.

co
co
.... N
" N .... 0 0 <..:l ' inst rument cl uste r display eac h time t he ig ni­
t io n is switc hed on or
off . The rema ining dis­
tance or time is displayed br ie fly .
- Inspection or oil change due: if your vehicle
has reac hed an inspection o r oi l change interval
o r both intervals at the same time, the mes­
sage
Inspection due! or Oil change due! or Oil
change and inspection due!
appears briefly af ­
te r swi tching t he igni tion on/off .
Checking service intervals
You can check t he rema ining distance o r time un­
til the ne xt oil change o r next inspection i n the
Ca r menu. To do this, select: t he
IC A RI fu nction
b utton
> (Car) * Systems cont rol b utton > Service
& checks > Service intervals.
Resetting the indicator
Your author ized Audi dealer or author ized A udi
Service Faci lity will reset the service interval dis­
p lay after pe rforming service.
I f yo u h ave cha nged t he oi l you rsel f, you must re­
set t he oil change in terva l.
To reset the indic ator, se le ct : th e
ICAR I fu nct ion
bu tton
> (Car) * Systems con trol button > Service
& checks > Service intervals. Tur n t he control
k nob downward to
Reset oil change interval and
p ress the cont rol knob.
- Only reset the oil ch ange in dicato r if the oil
was c hanged .
- Fo llow in g th e service i nte rv a ls is critical to
mai ntai ning th e service life a nd value o f
you r vehicle, especia lly t he engine. Even i f
t h e m ileage on the vehicle is low, do not ex ­
c e ed th e tim e for the n ext serv ic e .
- Calcu latin g the t ime to the next o il chan ge
i s interrupted w hen the ve hicle battery is
discon nect ed
c:> page 235.
Checking and Filling
209

Wheel s
® Mud and snow capability
"M/5" or "M+S" indicates the tire
is sui table for driving on mud and
snow.
& indicates a winter tire.
@ Composition of the tire cord
and materials
The number of plies indicates the
number of rubberized fabric lay­
ers in the t ire. In general: the
more layers, the more weight a
tire can carry . Tire manufacturers
must also specify the materials
used in the tire. These include
steel, nylon, po lyester and other
materials.
@ Maximum permitted load
This number indicates the maxi­
mum load in kilograms and
pounds that the tire can carry .
@Uniform tire quality grade
standards for treadwear,
traction and temperature resist ance
Tread wear, traction and temper ­
ature ranges¢
page 227.
@ Running direction
The arrows indicate the running
direction of unidirectional t ires .
You must always follow the speci­
fied running direction
¢page 241 .
212
@ Ma ximum permitted
inflation pressure
This number indicates the maxi­
mum pressure to which a tire can
be inflated under normal operat ­
ing condit ions.
Glossary of tire and loading
terminology
Acces sory we ight
means the combined weight (in
excess of those standard items
which may be replaced) of auto­ matic transmission, power steer­
ing, power brakes, power win­
dows, power seats, radio, and
heater, to the extent that these
items are available as factory-in­
stalled equipment (whether in ­
stalled or not) .
Aspect ratio
means the ratio of the height to
the width of the tire in percent .
Numbers of 55 or lower indicate a
low sidewall for improved steer­
ing response and better overall
handling on dry pavement.
Bead
means the part of the tire that is
made of steel wires, wrapped or
reinforced by ply cords and that is
shaped to fit the r im . ...

a,
a,
..... N ,.__ N ..... 0
s ..
for the number of seating posi­
tions. Refer to the table ¢
table
on page 222
for the number of
people that correspond to the ve­
hicle normal load.
New tires or wheels
Audi recommends having all work on tires or wheels performed by
an author ized Audi dealer or au­
thorized Audi Service Facility.
These facilities have the proper
knowledge and are equipped with
the required tools and replace­
ment parts.
.,.New tires do not yet have the
optimum gripping properties. Drive carefully and at moderate
speeds for the first 350 miles
(500 km) with new tires.
.,.Use tires of the same construc­
tion, size (rolling circumference)
and as close to the same tread
pattern as possible on all four
wheels.
.,.Do not replace tires individually .
At least replace both tires on the
same axle at the same time.
.,.Audi recommends that you use
Audi Original Tires. If you would
like to use different tires, please
note that the tires may perform
Wheels
differently even if they are the
same size¢.&,. .
.,. If you would like to equip your
vehicle with a tire/rim combina­
tion that is different from what
was installed at the factory, con­
sult with an authorized Audi
dealer or authorized Audi Service
Facility before making a pur­
chase¢ .&,..
The spare tire* is different from
the regular tires installed on the
vehicle -for example, if winter
tires or wide tires are installed -
so only use the spare tire* tempo­
rarily in case of emergency and
drive carefully while it is in use . It
should be replaced with a regular
tire as soon as possible.
Applies to: vehicles with all whee l dr ive
All four wheels must be equipped
with tires that are the same brand
and have the same construction
and tread pattern so that the drive system is not damaged by
different tire speeds. For this rea­
son, in case of emergency, only
use a spare tire* that is the same
circumference as the regular
tires. ,..
217