2017 AUDI A3 SEDAN jack points

car to keep your balance and take care not
to slip .
Raising the vehicle
The vehicle must be li~ed with the jack first be­
fore the wheel con be removed .
Fig. 291 S ill pane ls: mark ings (example)
F ig. 292 S ill: position ing the ve hicle jack
"Engage the parkin g brak e to prevent your vehi­
cle from roll ing unintentionally .
"Move the se lector le ver to p osition P .
"Find the markin g (imprint) on the s ill that is
nearest the whee l tha t will be changed
r::> fig. 291 . Behind the marking, there is a lift­
ing point on the sill for the vehicle jack.
"Vehicles with a sill: Note the position of the sill
when positioning the vehicle jack¢
fig. 292.
"Place the vehicle jack (vehicle tool kit) on a firm
surface. Use a flat, stable support if necessary.
On a slippery surface such as tile, you should
use a non-slip pad (such as a rubber mat) ¢
,&.
"Turn the ve hi cle jack located under the lifting
po int on the s ill to ra ise the jack until its
arm @
r::> fig. 292 is located under the des ignated plas-
gi tic mount r::> ,& , ¢0).
~ "Align the jack so that its arm @¢ fig. 292 en-
8 gages in the designated lift ing point in the door
~ sill and the movable base ® lies flat on the
Em ergen cy a ssis tanc e
ground. The base ® must be vertical unde r the
lifting point @.
"Wind the jack up further until the f lat tire
comes off the
ground ¢,& .
Position the vehicle jack only unde r the designat­
ed lifting points on the sill¢
fig. 291. T here is ex­
actly
one location for each wheel. The jack must
not be positioned at any other
location¢ ,&.¢0) .
An un sta b le surf ace under the jack can cause the
vehicle to slip off the jack . Always provide a firm
base for the jack on the ground. If necessary
place a sturdy board or similar support under the
jack. On
ha rd , s lippery surfa ces (such as tiles)
use a rubber mat or similar to prevent the jack
from
slipp ing ¢,&. .
.&, WARNING
-
-You o r you r passengers could be inj ured
while changing a wheel if you do not fo llow
these sa fety precautions :
- Position the vehicle jack only at the desig­
nated lifting points and align the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi­
c ient hold on the vehicle .
-A soft or unstable surface under the jack may cause the veh icle to slip off the jack.
Always provide a firm base for the jack on
the g ro u nd. If necessary, use a sturdy
board unde r the jack.
- On hard, slippe ry su rface (s uch as t iles)
u se a r ubber mat or simi lar to prevent the
j ac k from slipping.
- Only raise yo ur vehicle with the veh icle
j ac k prov ided by the factory.
If you use a
vehicle jack for another veh icle, your vehi­
cle can s lide and cause injury.
- Changes in load can affe ct the height of
the vehicle.
- Never star t the eng ine when the vehicle is
raised, which could cause an accident.
- Suppor t the vehicle se cur ely with appro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there
i s a potential risk for injury.
.,.
359

Emerg ency assis ta nce
-To help prevent injury to yourself and your
passengers:
-Do not ra ise the vehicle until you are sure
the jack is secure ly engaged.
-Passengers must not remain in the vehicle
when it is jacked up.
-Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
-Make sure jack posit ion is correct, adjust
as necessary and then cont inue to raise
the jack.
CD Note
Do not lift the vehicle by the sill. Position the
veh icle jack only at the designated lifting
points on the sill. Otherwise, your vehicle will
be damaged.
Taking the wheel off /installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig . 293 Changing a wheel: using the screwdr iver hand le
(with the blade removed) to turn the bolts
Fig. 29 4 Changing a wheel: alignm ent pin ins ide the top
ho le
360
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and re­
place the wheel as follows:
Removing the wheel
.. Use the he xago nal socket in th e screwdriver
handle
to comp letely remove the topmost
wheel bo lt and set it aside on a
clean surface
<=> fig. 293.
.. Screw the threaded end of the alig nm ent pi n
from the tool kit hand-tight into the empty bolt
hole
<=> fig. 294.
.. Then remove the other wheel bolts as described
above .
.. Take off the whee l leaving the alignment p in in
the bolt hole
<=> (j) .
Putting on the c omp act spare wheel
.. Lift the spare wheel and carefully slide it over
the alignment p in to gu ide it in place
<=>(j) .
.. Use the hexagonal socket in the screwdr iver
handle to screw in and t igh ten all wheel bolts
slightly.
.. Remove the alignmen t pin and insert and t igh t­
en the remaining wheel bolt s light ly like the
rest .
.. Turn the jack hand le counter-clockwise to lower
the vehicle until the jack is fully released .
.. Use the wheel bolt wrench to tighten all wheel
bolts
firmly <=> page 358. Tighten them cross­
wise,
from one bolt to the (approximately) op ­
posite one, to keep the wheel centered.
CD Note
When removing o r insta lling the wheel, the
rim could h it the brake rotor and damage the
r otor. Wor k carefully and have a second per­
son he lp yo u.
{!) Tips
Neve r use the hexagonal socket in the handle
of th e sc rewdriver to loos en o r tigh ten the
whee l bolts.
-Pull the reve rsible blade from the screwdr iv­
er befo re you use the hexagona l socket in
the handle to turn the whee l bolts.

Emergency situations
Loading the vehicle onto a flat bed truck
Fig. 309 Veh icle o n flat bed truck (example)
Front hook up
.. Align the vehicle with the centerline of the car
carrier ramp .
.. Attach the winch hook to the front towline eye
prev iously installed.
Rear hook up
.. Align the vehicle with the centerline of the car
carrier ramp .
.. Attach the winch hook to the rear towline eye
previously installed .
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp.
Raising the vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be lifted at the lifting
points illustrated.
Fig. 310 Front lifting point (example)
372
Fig. 311 Rear lifting point (exa mple )
.. Read and heed WARNING ¢&_ .
.. Locate lifting points <;!)fig. 310 and <;!) fig . 311.
.. Adjust lifting arms of workshop hoist or floor
jack to match vehicle lifting points .
.. Insert a rubber pad between the floor jack/
workshop hoist and the lifting points .
If you must lift your vehicle with a floor jack to
work underneath, be sure the vehicle is safely
supported on stands intended for this purpose .
Front lifting point
The lifting point is located on the floor pan rein­
forcement about at the same level as the jack
moun ting poin t¢ fig.
310. Do not lift the vehi­
cle at the vertical sill reinforcement.
Rear lifting point
The lifting point is located on the vertical rein­
forcement of the lower sill for the on-board jack
¢fig. 311.
Lifting with vehicle jack
Refer to c> page 359.
,&. WARNING
-To reduce the r isk of serious injury and vehi­
cle damage.
- Always lift the vehicle on ly at the special
workshop hoist and floor jack lift points il ­
l ustrated
c> fig. 310and c>fig. 311.
-Failure to lift the vehicle at these points
could cause the vehicle to tilt or fall from
a lift if there is a change in vehicle weight

CXl CXl .... N ,.__
N .... 0 N > 00
distr ibut ion an d ba lance . This might hap­
pen, for exam ple, when heavy compo­
nents such as the engine b lock or trans­
miss io n are removed.
- When removing heavy components like
t h ese, anc hor vehicle t o hoist o r add corr e­
sponding weights to maintain the center of
grav ity. Oth erwise, the ve hicle might ti lt or
s li p off the hois t, causing s eriou s perso na l
lnJUry.
(D Note
- Be awar e of the fo llowing poi nts before lift­
i ng t he vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan , the transmission housing, the front
or rear axle or the body side members .
This could lead to serious damage.
- To avoid damage to the unde rbody or
chassis frame, a rubber pad must be in­
serted between the floor jack and the lift
points.
- Before driv ing over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist .
- Before driving over a workshop hoist, en­
sure that there is sufficient clearance be­
tween the hoist and low parts of the ve ­
hicle.
Emergency situations
373