2017.5 VAUXHALL VIVARO clock

Vehicle care191Notice
The driving characteristics of the
repaired tyre is severely affected, therefore have this tyre replaced.
If unusual noise is heard or the
compressor becomes hot, turn
compressor off for at least
30 minutes.
Pay attention to storage information
and expiry date on sealant bottle. Its
sealing capability is not guaranteed
after this time.
Replace the used sealant bottle. Dispose of the sealant bottle as
prescribed by applicable laws.
Wheel changing
Some vehicles are equipped with a
tyre repair kit instead of a spare wheel 3 188.
Make the following preparations and
observe the following information:
● Park the vehicle on a level, firm and non-slippery surface. The
front wheels must be in the
straight-ahead position.
● Apply the parking brake and engage first gear or reverse gear.● Remove the spare wheel 3 192.
● Never change more than one wheel at a time.
● Use the jack only to change wheels in case of puncture, not
for a seasonal winter or summer
tyre change.
● The jack is maintenance-free. ● If the ground on which the vehicle
is standing is soft, a solid board
(max. 1 cm thick) should be
placed under the jack.
● Remove heavy objects out of the
vehicle before jacking up.
● No people or animals may be in the vehicle when it is jacked-up.
● Never crawl under a jacked-up vehicle.
● Do not start the engine when the vehicle is raised on the jack.
● Clean wheel bolts/nuts and thread with a clean cloth before
mounting the wheel.9 Warning
Do not grease wheel bolt, wheel
nut and wheel nut cone.
1. Remove the wheel cover (using the hook supplied). Vehicle tools
3 182.
2. Loosen each of the wheel bolts by
half a turn using the wheel
wrench. Ensure the wrench
locates securely. The wrench
should turn anticlockwise to
loosen the bolts. Invert the wrench if necessary.

192Vehicle care
3.Place lifting pad spigot of the jack
under the jacking hole located
nearest the wheel concerned.
Ensure the jack is positioned
correctly. The jack base must be
on the ground directly below the
jacking hole in a manner that
prevents it from slipping.
4. Install wrench onto the jack and raise the vehicle by turning the
wrench until the wheel is clear of
the ground.
5. Unscrew wheel bolts completely by turning anticlockwise and wipe
clean with a cloth.
Put wheel bolts somewhere
where the threads will not be
soiled.
6. Change the wheel. Spare wheel 3 192.
7. Screw in the wheel bolts.
8. Lower the vehicle and remove jack.
9. Tighten each of the wheel bolts in
a crosswise sequence using the
wheel wrench. Ensure the wrench locates securely. The wrench
should turn clockwise to tighten
the bolts. Invert the wrench if
necessary.
Tightening torque is 160 Nm.
10. Replace the wheel cover, ensuring that the valve hole in thewheel cover is aligned with the
tyre valve before installing.
Notice
If applicable, fit anti-theft bolts
nearest the tyre valve (otherwise it
may not be possible to refit the wheel
cover).11. Stow the replaced wheel 3 192
and the vehicle tools 3 182.
12. Have the new wheel balanced on the vehicle.
Check the tyre pressure of the
installed tyre 3 216.
Check the wheel bolt torque.
Have the defective tyre renewed or
repaired as soon as possible.
Spare wheel
Some vehicles are equipped with a tyre repair kit instead of a spare wheel
3 188.
If mounting a spare wheel which is
different from the other wheels, this
wheel might be classified as a
temporary spare wheel and the
corresponding speed limits apply,
even though no label indicates this.
Seek the assistance of a workshop to
check the applicable speed limit.

Vehicle care195
Lead connection order:1. Connect the red lead to the positive terminal (1) of the booster
battery.
2. Connect the other end of the red lead to the positive terminal (2) of
the discharged vehicle battery.
3. Connect the black lead to the negative terminal (3) of the
booster battery.
4. Connect the other end of the black
lead to a vehicle grounding point
(4), such as the engine block or an
engine mounting bolt. Connect as
far away from the discharged
vehicle battery as possible,
however at least 60 cm.
Route the leads so that they cannot
catch on rotating parts in the engine
compartment.
To start the engine: 1. Start the engine of the vehicle providing the jump start.
2. After five minutes, start the other engine. Start attempts should be
made for no longer than
15 seconds at an interval of
one minute.
3. Allow both engines to idle for approx. three minutes with the
leads connected.
4. Switch on electrical consumers (e.g. headlights, heated rear
window) of the vehicle receiving
the jump start.
5. Reverse above sequence exactly when removing leads.Towing
Towing the vehicle The towing eye is stowed with thevehicle tools 3 182.
Release cap using a suitable tool.
Screw the towing eye clockwise into
the front towing point and tighten fully
using the wheel wrench.
Attach a tow rope - or better still a tow rod - to the towing eye, never to the
bumper or front suspension units.

223Charging system .......................... 96
Child locks ................................... 30
Child restraint installation locations ................................... 66
Child restraints.............................. 63
Child restraint systems ................63
Cigarette lighter ........................... 88
Cleaning the vehicle ...................197
Climate control ............................. 15
Climate control systems .............114
Clock ............................................ 86
Coat hooks ................................... 73
Coin holder ................................... 71
Collision damage repair ..............219
Control indicators.......................... 92
Control of the vehicle .................128
Controls ........................................ 83
Controls in steering wheel ............83
Convex shape .............................. 39
Coolant ....................................... 166
Coolant and antifreeze ...............201
Coolant heater ............................ 119
Cooling (A/C) .............................. 115
Cornering light ............................ 108
Cruise control ....................100, 149
Cupholders .................................. 73
Curtain airbag system .................. 61D
Danger, Warnings and Cautions ...4
Dashboard .................................... 10
Daytime running lights ........107, 108
Declaration of conformity ............217
DEF ............................................ 137
Demisting and defrosting ..............15
Diesel exhaust fluid ....................137
Diesel fuel filter .......................... 170
Diesel fuel system bleeding .......170
Diesel particle filter ....................136
Directional tyres ..................183, 192
Distance to service .......................91
Document tray .............................. 73
Door locks..................................... 24
Door open .................................. 100
Door panel storage .......................74
Doors ............................................ 31
Double cab ................................... 74
DPF (diesel particle filter) ...........136
Driver assistance systems ..........149
Driver Information Centre ...........100
Driving characteristics and towing tips .............................. 159
Driving economically................... 127
Driving hints ........................ 127, 128
Driving style indicator ...................91E
ECO mode .................................. 127
ecoScoring.................................. 103
Electric adjustment ......................39
Electrical accessories ...................86
Electrical system......................... 178
Electronic climate control system 116
Electronic data recording ..............41
Electronic key system ...................22
Electronic Stability Program 97,
147, 160
Electronic Stability Program off ...97
End-of-life vehicle recovery .......163
Engine air filter............................ 165
Engine air flow indicator .............165
Engine coolant ........................... 166
Engine coolant temperature ........97
Engine data ............................... 206
Engine Drag Torque Control ......147
Engine exhaust .......................... 136
Engine identification ...................204
Engine oil ...........164, 201, 205, 215
Engine oil additives ....................201
Engine oil level .......................... 102
Engine oil pressure ......................98
Engine oil viscosity grades .........201
Enhanced Traction function 146, 147
Entry lighting .............................. 112
Event data recorders ..................219
Exhaust gases ....................136, 195