2016 YAMAHA YZF-R6 display

Instrument and control functions
3-5
3 If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on after
refueling, have a Yamaha dealer check
the vehicle.
TIPThis model is equipped with a self-di-
agnosis device for the fuel level detec-
tion circuit. If a problem is detected in
the fuel level detection circuit, the fuel
level warning light will flash repeatedly.
If this occurs, have a Yamaha dealer
check the vehicle.
EAU1142E
Coolant temperature warnin
g
li g ht “ ”
This warning light comes on if the en-
gine overheats. If this occurs, reduce
the load on the engine immediately. If
message “HI” flashes in the coolant
temperature display, stop the vehicle,
then stop the engine and let the engine
cool.
The electrical circuit of the warning
light can be checked by turning the key
to “ON”. The warning light should
come on for a few seconds, and then
go off. If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.
NOTICE
ECA10022
Do not continue to operate the en-
g
ine if it is overheatin g.TIP For radiator-fan-equipped vehi-
cles, the radiator fan(s) automati-
cally switch on or off according to
the coolant temperature in the ra-
diator.
 If the engine overheats, see page
6-46 for further instructions.
U2CXE2E0.book Page 5 Tuesday, June 9, 2015 5:04 PM

Instrument and control functions
3-6
3
Display Conditions What to do
Under 40 °C
(Under 104 °F) Message “Lo” is displayed. OK. Go ahead with riding.
40–116 °C
(104–242 °F) Coolant temperature is dis-
played.
OK. Go ahead with riding.
117–134 °C
(243–274 °F) Coolant temperature flash-
es.
Warning light comes on.Reduce the load on the engine by riding
at a moderate pace, at low rpm, until
the coolant temperature goes down.
If the temperature does not go down,
stop the engine. (See page 6-46.)
Above 134 °C
(Above 274 °F) Message “HI” flashes.
Warning light is on.Stop the engine and allow it to cool.
(See page 6-46.)
TRIP A
˚C
TRIP A
˚C
TRIP A
˚C
TRIP A
˚C
U2CXE2E0.book Page 6 Tuesday, June 9, 2015 5:04 PM

Instrument and control functions
3-8
3
EAU3904D
Multi-function meter unit
WARNING
EWA12423
Be sure to stop the vehicle before
makin g any settin g chan ges to the
multi-function meter unit. Chang ing
settin gs while ri din g can distract the
operator an d increase the risk of an
acci dent.
The multi-function meter unit is
equipped with the following:
 a speedometer
 a tachometer
 an odometer
 two tripmeters
 a fuel reserve tripmeter
 a stopwatch
 a clock
 a coolant temperature display
 an air intake temperature display
 a self-diagnosis device
 a display brightness and shift tim-
ing indicator light control modeTIPExcept when entering the display
brightness and shift timing indica-
tor light control mode, turn the key
to “ON” before using the “SE-
LECT” and “RESET” buttons.
 For the UK: To switch the multi-
function meter unit between kilo-
meters and miles, press the “SE-
LECT” button for one second.Speed ometer
The speedometer shows the vehicle’s
traveling speed. Tachometer
The tachometer shows the engine
speed in crankshaft revolutions per mi-
nute (r/min).
When the vehicle is first powered on,
the tachometer needle will sweep once
across the r/min range and then return
to zero r/min in order to test the electri-
cal circuit.
NOTICE
ECA10032
Do not operate the en
gine in the ta-
chometer red zone.
Re d zone: 16500 r/min an d a bove
1. Speedometer
2. Clock
3. Tachometer
4. Coolant temperature display/air intake tem-
perature display
5. Odometer/tripmeter/fuel reserve tripme- ter/stopwatch
6. Shift timing indicator light
7. “RESET” button
8. “SELECT” button
SELECT
RESET2
3
4
5
6
1
87
1. Tachometer
2. Tachometer red zone
2
1
U2CXE2E0.book Page 8 Tuesday, June 9, 2015 5:04 PM

Instrument and control functions
3-9
3 Clock
The clock uses a 12-hour time system.
To set the clock
1. Turn the key to “ON”.
2. Push both the “SELECT” button
and “RESET” button for two sec-
onds. The hour digits will start
flashing.
3. Push the “RESET” button to set the hours.
4. Push the “SELECT” button, and the minute digits will start flashing.
5. Push the “RESET” button to set the minutes.
6. Push the “SELECT” button to con- firm settings and start the clock. O
dometer, tripmeters, an d stop-
watch
O dometer an d tripmeters
The odometer shows the total distance
traveled by the vehicle.
The tripmeters show the distance trav-
eled since they were last reset.
TIP The odometer will lock at 999999.
 The tripmeters will reset and con-
tinue counting after 9999.9 is
reached.During normal operation, push the
“SELECT” button to change the dis-
play between the odometer “ODO”, the tripmeters “TRIP A” and “TRIP B”,
and the stopwatch in the following or-
der:
TRIP A
→ TRIP B → ODO → Stop-
watch → TRIP A
If the fuel level warning light comes on,
the display will automatically change to
the fuel reserve tripmeter “F-TRIP” and
start counting the distance traveled
from that point. In this case, push the
“SELECT” button to change the dis-
play in the following order:
F-TRIP → Stopwatch → TRIP A →
TRIP B → ODO → F-TRIP
To reset a tripmeter, push the “SE-
LECT” button to change the display to
the tripmeter you want to reset, and
then push the “RESET” button for one
second. If you do not reset the fuel re-
serve tripmeter manually, after refuel-
ing and traveling 5 km (3 mi), it will
reset automatically and disappear from
the display.
1. Clock
km/h
TRIP A
1
1. Odometer/tripmeter/fuel reserve tripme- ter/stopwatch
TRIP A
˚C
1
U2CXE2E0.book Page 9 Tuesday, June 9, 2015 5:04 PM

Instrument and control functions
3-10
3
Stopwatch
To use the stopwatch, push the “SE-
LECT” button to change the display to
the stopwatch (the digits will flash
when the stopwatch is selected), and
then push the “SELECT” button for a
few seconds until the digits stop flash-
ing. The stopwatch can now be used
as follows:
Standard measurement
1. Push the “RESET” button to start
the stopwatch.
2. Push the “SELECT” button to stop the stopwatch.
3. Push the “SELECT” button again to reset the stopwatch.
Split-time measurement1. Push the “RESET” button to start the stopwatch.
2. Push the “RESET” button or start switch “ ” to measure split-
times. (The colon “:” will start
flashing.) 3. Push the “RESET” button or start
switch “ ” to display the final
split-time or push the “SELECT”
button to stop the stopwatch and
display total elapsed time.
4. Push the “SELECT” button to re- set the stopwatch.
TIPTo exit the stopwatch, push the “SE-
LECT” button for a few seconds until
the digits start flashing.Coolant temperature display
The coolant temperature display indi-
cates the temperature of the coolant.
See page 3-6 for a full explanation.
TIPWhen the coolant temperature display
is selected, “C” is displayed for one se-
cond, and then the coolant tempera-
ture is displayed.NOTICE
ECA10022
Do not continue to operate the en-
g ine if it is overheatin g.Air intake temperature display
The air intake temperature display indi-
cates the temperature of the air drawn
into the air intake duct. Push the “RE-
SET” button to switch the display be-
tween the coolant temperature and the
air intake temperature.
1. Coolant temperature display
TRIP A
˚C
1
1. Air intake temperature display
TRIP A
˚C
1
U2CXE2E0.book Page 10 Tuesday, June 9, 2015 5:04 PM

Instrument and control functions
3-11
3
TIP When the air intake temperature is
below –9 °C, “LO” will be dis-
played.
 Even when the air intake tempera-
ture is displayed, the coolant tem-
perature warning light comes on if
the engine overheats.
 When the key is turned to “ON”,
the coolant temperature is auto-
matically displayed, even if the air
intake temperature was displayed
prior to turning the key to “OFF”.
 When the air intake temperature
display is selected, “A” is dis-
played for one second, and then
“A” and the air intake temperature
are displayed.
Self- dia gnosis device
This model is equipped with a self-di-
agnosis device for various electrical
circuits. If a problem is detected in any
of those circuits, the engine trouble
warning light will come on and the dis-
play will indicate an error code. If the
display indicates any error codes, note
the code number and have a Yamaha
dealer check the vehicle.
The self-diagnosis device also detects
problems in the immobilizer system
circuits. If a problem is detected in the
immobilizer system circuits, the immo- bilizer system indicator light will flash
and the display will indicate an error
code.
TIPIf the display indicates error code 52,
this could be caused by transponder
interference. If this error code appears,
try the following:1. Use the code re-registering key to
start the engine.TIPMake sure there are no other immobi-
lizer keys close to the main switch, and
do not keep more than one immobilizer
key on the same key ring! Immobilizer
system keys may cause signal interfer-
ence, which may prevent the engine
from starting.2. If the engine starts, turn it off andtry starting the engine with the
standard keys.
3. If one or both of the standard keys do not start the engine, take the
vehicle, the code re-registering
key and both standard keys to a
Yamaha dealer and have the stan-
dard keys re-registered.
1. Immobilizer system indicator light
2. Engine trouble warning light “ ”
3. Error code display
321
U2CXE2E0.book Page 11 Tuesday, June 9, 2015 5:04 PM

Instrument and control functions
3-12
3
NOTICE
ECA11591
If the display in dicates an error co-
d e, the vehicle shoul d b e checked as
soon as possi ble in or der to avoi d
en gine damag e.Display bri ghtness and shift timing
in dicator li ght control mo de
This mode cycles through five control
functions, allowing you to make the fol-
lowing settings in the order listed be-
low. 
Display brightness:
This function allows you to adjust
the brightness of the displays and
tachometer.
 Shift timing indicator light activity
function:
This function allows you to set the
indicator light to on, flash, or off.
 Shift timing indicator light activa-
tion:
This function allows you to select
the engine speed at which the in-
dicator light will be activated.
 Shift timing indicator light deacti-
vation:
This function allows you to select
the engine speed at which the in-
dicator light will be deactivated.
 Shift timing indicator light bright-
ness:
This function allows you to adjust
the brightness of the shift timing
indicator light.
TIPThe brightness level display shows the
brightness level setting.
To adjust the brightness of the displaysand tachometer1. Turn the key to “OFF”.
2. Push and hold the “SELECT” but-
ton.
3. Turn the key to “ON”, and then re- lease the “SELECT” button after
five seconds.
4. Push the “RESET” button to select the desired brightness level.
5. Push the “SELECT” button to con- firm the selected brightness level.
The control mode changes to the
shift timing indicator light activity
function.
To set the shift timing indicator light ac-tivity function1. Push the “RESET” button to select one of the following indicator light
activity settings: On - the indicator light will
come on when activated.
(This setting is selected when
the indicator light stays on.)
1. Shift timing indicator light activation range
2. Brightness adjustable displays
3. Brightness level display
4. Shift timing indicator light
km/h
1
2
3
4
2
U2CXE2E0.book Page 12 Tuesday, June 9, 2015 5:04 PM

Operation and important rid ing points
5-1
5
EAU15952
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10272
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which coul d cause an acci dent
or injury.
EAU47152
TIPThis model is equipped with:  a lean angle sensor to stop the en-
gine in case of a turnover. In this
case, the display will indicate error
code 30, but this is not a malfunc-
tion. Turn the key to “OFF” and
then to “ON” to clear the error co-
d e . F ai l in g to do s o wi ll pr e v e nt the
engine from starting even though
the engine will crank when push-
ing the start switch.
 an engine auto-stop system. The
engine stops automatically if left
idling for 20 minutes. In this case,
the display will indicate error code
70, but this is not a malfunction.
Push the start switch to clear the
error code and to restart the en-
gine.
EAU33016
Startin g the en gineIn order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
 The transmission is in the neutral
position.
 The transmission is in gear with
the clutch lever pulled and the
sidestand up.
See page 3-28 for more informa-
tion.
1. Turn the key to “ON” and make sure that the engine stop switch is
set to “ ”.
The following warning lights and
indicator lights should come on for
a few seconds, then go off. Oil level warning light
 Fuel level warning light
 Coolant temperature warning
light
 Shift timing indicator light
 Engine trouble warning light
 Immobilizer system indicator
light
U2CXE2E0.book Page 1 Tuesday, June 9, 2015 5:04 PM