2016 YAMAHA XVS950CU reset

Instrument and control functions
3-6
3

a clock
 an error code display
TIPThe key must be turned to “ON”
before you can use the “SELECT”
and “RESET” switches.
 For the U.K. only: To switch the
speedometer and odometer/trip-
meter displays between kilome-
ters and miles, push the
“SELECT” switch for at least three
seconds.
Odometer, tripmeters, an d clock
The odometer shows the total distance
traveled by the vehicle.
The tripmeters show the distance trav-
eled since they were last reset.
The fuel reserve tripmeter shows the
distance traveled on the fuel reserve.
The clock displays time in 12-hour for-
mat.TIP The odometer will lock at 999999
km.
 The tripmeters will reset and con-
tinue counting after 999.9 km is
reached.
In normal operation, push the “SE-
LECT” switch to change the display
between the odometer “ODO”, the
tripmeter “TRIP 1” and “TRIP 2”, and
the clock in the following order:
ODO → TRIP 1 → TRIP 2 → clock →
ODO
If the fuel level warning light comes on,
the display will change to the fuel re-
serve tripmeter “TRIP F” and start
counting the distance traveled from
that point. In this case, push the “SE-
LECT” switch to change the display in
the following order:
TRIP F → TRIP 1 → TRIP 2 → clock →
ODO → TRIP F
To reset a tripmeter, use the “SELECT”
switch to change the display to the de-
sired tripmeter and then push the “RE-
SET” switch for one second. The fuel
reserve tripmeter can be reset manual-
ly, or after refueling and traveling 5 km
(3 mi) it will reset automatically and dis-
appear from the display.
1. “SELECT” switch
2. “RESET” switch
1
2
1. Odometer/tripmeter/fuel reserve tripme- ter/clock
1
U2DEE1E0.book Page 6 Friday, September 4, 2015 4:52 PM

Instrument and control functions
3-7
3 To set the clock
1. Push the “SELECT” and “RESET”
switches for three seconds. The
hour digits will start flashing.
2. Use the “SELECT” switch to set the hours.
3. Push the “RESET” switch. The minute digits will start flashing.
4. Use the “SELECT” switch to set the minutes.
5. Push the “RESET” switch for two seconds to confirm setting chang-
es and start the clock. Error co
de display
This vehicle is equipped with a self-di-
agnosis function for various electrical
circuits. If a problem is detected in any
of those circuits, the engine trouble
warning light will come on and the dis-
play will indicate an error code. If the
display indicates any error codes, note
the code number and have a Yamaha
dealer check the vehicle.
NOTICE
ECA11591
If the display in dicates an error
co de, the vehicle shoul d b e checked
as soon as possi ble in or der to avoi d
en gine damag e.
The self-diagnosis function also de-
tects problems in the immobilizer sys-
tem circuits. If a problem is detected in
any of those circuits, the immobilizer
system indicator light will flash and the
display will indicate an error code.TIPIf the display indicates error code 52,
this could be caused by transponder
interference. If this error code appears,
try the following:1. Make sure there are no other im-
mobilizer keys close to the main
switch. Other immobilizer system
keys may cause signal interfer-
ence and prevent the engine from
starting.
2. Use the code re-registering key to start the engine.
3. If the engine starts, turn it off and try starting the engine with the
standard keys.
4. If one or both of the standard keys do not start the engine, take the
vehicle and all three keys to a
Yamaha dealer to have the stan-
dard keys re-registered.
1. Clock
1
1. Error code display
2. Engine trouble warning light “ ”
3. Immobilizer system indicator light “ ”
123
U2DEE1E0.book Page 7 Friday, September 4, 2015 4:52 PM

Instrument and control functions
3-8
3
EAU1234H
Han dle bar switchesLeft Ri
ght
EAU12352
Pass switch “ ”
Press this switch to flash the headlight.TIPWhen the dimmer switch is set
to “ ”, the passing switch has no ef-
fect.
EAU12401
Dimmer switch “ / ”
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
EAU12461
Turn si gnal switch “ / ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When
released, the switch returns to the cen-
ter position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU12501
Horn switch “ ”
Press this switch to sound the horn.
EAU12661
En gine stop switch “ / ”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12713
Start switch “ ”
Push this switch to crank the engine
with the starter. See page 5-1 for start-
ing instructions prior to starting the en-
gine.
1. Pass switch “ ”
2. Dimmer switch “ / ”
3. Turn signal switch “ / ”
4. Horn switch “ ”
3
4 12
1. Engine stop switch “ / ”
2. “SELECT” switch
3. “RESET” switch
4. Start switch “ ”
5. Hazard switch “ ”
1
5 2
3
4
U2DEE1E0.book Page 8 Friday, September 4, 2015 4:52 PM

Instrument and control functions
3-9
3
EAU41701
The engine trouble warning light will
come on when the key is turned to
“ON” and the start switch is pushed,
but this does not indicate a malfunc-
tion.
EAU12735
Hazar d switch “ ”
With the key in the “ON” or “ ” posi-
tion, use this switch to turn on the haz-
ard lights (simultaneous flashing of all
turn signal lights).
The hazard lights are used in case of an
emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.NOTICE
ECA10062
Do not use the hazard lights for an
exten ded len gth of time with the en-
g ine not runnin g, otherwise the bat-
tery may dischar ge.
EAU55701
“SELECT” switch
This switch is used to perform selec-
tions in the odometer and tripmeters
and to set the clock of the multi-func-
tion meter unit. See “Multi-function meter unit” on
page 3-5 for detailed information.
EAU55711
“RESET” switch
This switch is used to reset the tripme-
ters and to set the clock of the multi-
function meter unit.
See “Multi-function meter unit” on
page 3-5 for detailed information.
EAU12822
Clutch leverThe clutch lever is located on the left
side of the handlebar. To disengage
the clutch, pull the lever toward the
handlebar grip. To engage the clutch,
release the lever. The lever should be
pulled rapidly and released slowly for
smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-18.)1. Clutch lever
1
U2DEE1E0.book Page 9 Friday, September 4, 2015 4:52 PM

10-1
10
Index
AABS (for ABS models) .......................... 3-11
ABS warning light (for ABS models) ....... 3-4
Air filter element, replacing ................... 6-13
Auxiliary light bulb, replacing ............... 6-30BBattery .................................................. 6-25
Brake and clutch levers, checking and
lubricating........................................... 6-23
Brake and shift pedals, checking and lubricating........................................... 6-22
Brake fluid, changing............................ 6-20
Brake fluid level, checking.................... 6-19
Brake lever............................................ 3-10
Brake lever free play, checking ............ 6-17
Brake light switches ............................. 6-18
Brake pedal .......................................... 3-10
Brake/tail light....................................... 6-31CCables, checking and lubricating ......... 6-21
Care ........................................................ 7-1
Catalytic converter ............................... 3-14
Clutch lever............................................. 3-9
Clutch lever free play, adjusting ........... 6-16DDimmer switch........................................ 3-8
Drive belt slack ..................................... 6-21EEngine break-in ...................................... 5-3
Engine oil and oil filter cartridge ........... 6-10
Engine serial number .............................. 9-1
Engine stop switch ................................. 3-8
Engine trouble warning light ................... 3-4
FFront and rear brake pads, checking ... 6-18
Front fork, checking ............................. 6-24
Fuel ...................................................... 3-12
Fuel consumption, tips for reducing ...... 5-3
Fuel level warning light........................... 3-4
Fuel tank breather/overflow hose ........ 3-14
Fuel tank cap........................................ 3-12
Fuses, replacing ................................... 6-27HHandlebar switches ............................... 3-8
Hazard switch ........................................ 3-9
Headlight bulb, replacing ..................... 6-29
High beam indicator light ....................... 3-3
Horn switch ............................................ 3-8IIdentification numbers ........................... 9-1
Ignition circuit cut-off system .............. 3-18
Immobilizer system ................................ 3-1
Immobilizer system indicator light ......... 3-5
Indicator lights and warning lights ......... 3-3LLicense plate light ................................ 6-32MMain switch ............................................ 3-2
Maintenance and lubrication, periodic... 6-4
Maintenance, emission control
system ................................................. 6-3
Matte color, caution ............................... 7-1
Model label............................................. 9-1
Multi-function meter unit ........................ 3-5NNeutral indicator light ............................. 3-3
OOil level warning light .............................. 3-3PPanel, removing and installing ................ 6-8
Parking.................................................... 5-4
Part locations.......................................... 2-1
Pass switch............................................. 3-8RRESET switch ......................................... 3-9
Rider seat.............................................. 3-15SSafety information................................... 1-1
SELECT switch ....................................... 3-9
Shifting.................................................... 5-2
Shift pedal............................................. 3-10
Shock absorber assemblies,
adjusting ............................................. 3-16
Sidestand.............................................. 3-17
Sidestand, checking and
lubricating ........................................... 6-23
Spark plugs, checking ............................ 6-8
Specifications ......................................... 8-1
Starting the engine ................................. 5-1
Start switch ............................................. 3-8
Steering, checking ................................ 6-25
Steering lock ......................................... 3-15
Storage ................................................... 7-3
Supporting the motorcycle ................... 6-32
Swingarm pivots, lubricating ................ 6-24TThrottle grip and cable, checking and lubricating ........................................... 6-22
Throttle grip free play, checking ........... 6-13
Tires ...................................................... 6-14
U2DEE1E0.book Page 1 Friday, September 4, 2015 4:52 PM