2016 YAMAHA XMAX 125 lights

For your safety – pre-operation checks
4-2
4
Wheels and tires•Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.6-18,
6-20
Brake levers• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.6-25
Centerstand, side-
stand• Make sure that operation is smooth.
• Lubricate pivots if necessary.6-25
Chassis fasteners• Make sure that all nuts, bolts and screws are properly
tightened.
• Tighten if necessary.—
Instruments, lights,
signals and switches• Check operation.
• Correct if necessary.—
Sidestand switch • Check operation of ignition circuit cut-off system.
• If system is not working correctly, have Yamaha dealer
check vehicle.3-23 ITEM CHECKS PAGE
U2DME2E0.book Page 2 Tuesday, June 30, 2015 11:38 AM

Operation and important riding points
5-5
5
EAU16821
Tips for reducing fuel con-
sumption
Fuel consumption depends largely on
your riding style. Consider the follow-
ing tips to reduce fuel consumption:
Avoid high engine speeds during
acceleration.
Avoid high engine speeds with no
load on the engine.
Turn the engine off instead of let-
ting it idle for an extended length
of time (e.g., in traffic jams, at traf-
fic lights or at railroad crossings).
EAU16831
Engine break-in
There is never a more important period
in the life of your engine than the period
between 0 and 1000 km (600 mi). For
this reason, you should read the fol-
lowing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1000 km (600 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that
might result in engine overheating
must be avoided.
EAUS1841
0–500 km (0–300 mi)
Avoid prolonged operation above 5000
r/min.
500–1000 km (300–600 mi)
Avoid prolonged operation above 7500
r/min. NOTICE: After 1000 km (600
mi) of operation, be sure to replace
the engine oil, final transmission oil
and the oil filter element.
[ECA12932]
1000 km (600 mi) and beyond
The vehicle can now be operated nor-
mally.
NOTICE
ECA10311
Keep the engine speed out of
the tachometer red zone.
If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.
U2DME2E0.book Page 5 Tuesday, June 30, 2015 11:38 AM

Periodic maintenance and adjustment
6-6
6
EAU38263
TIP
Engine air filter and V-belt air filters
• This model’s engine air filter is equipped with a disposable oil-coated pa-
per element, which must not be cleaned with compressed air to avoid
damaging it.
• The engine air filter element needs to be replaced and the V-belt air filter
elements need to be serviced more frequently when riding in unusually wet
or dusty areas.
Hydraulic brake service
• After disassembling the brake master cylinders and calipers, always
change the fluid. Regularly check the brake fluid levels and fill the reser-
voirs as required.
• Every two years replace the internal components of the brake master cyl-
inders and calipers, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
27*Lights, signals and
switches• Check operation.
• Adjust headlight beam.√√√√√√ NO. ITEM
X 1000 km CHECK OR
MAINTENANCE JOB
X 1000 mi
ODOMETER
READING
ANNUAL CHECK
16121824
0.63.5710.514
U2DME2E0.book Page 6 Tuesday, June 30, 2015 11:38 AM

Periodic maintenance and adjustment
6-31
6
EAU34242
Replacing a headlight bulb
This model is equipped with halogen
bulb headlights. If a headlight bulb
burns out, have a Yamaha dealer re-
place it and, if necessary, adjust the
headlight beam.
EAUM3680
Auxiliary lights
This vehicle is equipped with two aux-
iliary lights. Depending on the model,
the auxiliary lights may be bulb-type or
LED-type.
If an auxiliary light does not come on,
have a Yamaha dealer check the elec-
trical circuit and replace the light if nec-
essary.
U2DME2E0.book Page 31 Tuesday, June 30, 2015 11:38 AM

Periodic maintenance and adjustment
6-34
6
EAUM2203
Replacing the license plate
light bulb
1. Remove the socket (together with
the bulb) by pulling it out.
2. Remove the burnt-out bulb by
pulling it out.
3. Insert a new bulb into the socket.
4. Install the socket (together with
the bulb) by pushing it in.
EAU25882
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter re-
quire any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the scooter prop-
erly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWA15142
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water
heaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or prop-
erty damage.
1. License plate light bulb socket
ZAUM0681
1
U2DME2E0.book Page 34 Tuesday, June 30, 2015 11:38 AM

Scooter care and storage
7-2
7 structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.
Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake fluid,
antifreeze or electrolyte.
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaningcompounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quality
plastic polishing compound
af-
ter washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the en-
gine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.
[ECA10792]
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to pre-
vent corrosion.
U2DME2E0.book Page 2 Tuesday, June 30, 2015 11:38 AM

10-1
10
Index
A
ABS (for ABS models) .......................... 3-16
ABS warning light (for ABS models)....... 3-4
Acceleration and deceleration................ 5-3
Air filter and V-belt case air filter
elements ............................................ 6-15
Auxiliary lights ...................................... 6-31
B
Battery .................................................. 6-27
Brake fluid, changing ........................... 6-23
Brake fluid level, checking ................... 6-22
Brake lever, front .................................. 3-15
Brake lever, rear ................................... 3-16
Brake levers, lubricating ....................... 6-25
Braking ................................................... 5-4
C
Cables, checking and lubricating ......... 6-24
Care ........................................................ 7-1
Catalytic converters ............................. 3-19
Centerstand and sidestand, checking
and lubricating ................................... 6-25
Coolant ................................................. 6-14
D
Dimmer switch ..................................... 3-14
E
Engine break-in ...................................... 5-5
Engine oil .............................................. 6-10
Engine trouble warning light................... 3-4
F
Final transmission oil ............................ 6-13
Front and rear brake lever free play,
checking............................................. 6-20
Front and rear brake pads, checking ... 6-21
Front fork, checking ............................. 6-26
Front turn signal light ........................... 6-32
Fuel....................................................... 3-18
Fuel consumption, tips for reducing ...... 5-5
Fuel level warning light ........................... 3-4
Fuel tank cap........................................ 3-17
Fuses, replacing ................................... 6-29
H
Handlebar switches.............................. 3-14
Hazard switch ...................................... 3-14
Headlight bulb, replacing ..................... 6-31
High beam indicator light ....................... 3-4
Horn switch .......................................... 3-14
I
Identification numbers............................ 9-1
Ignition circuit cut-off system............... 3-24
Immobilizer system ................................ 3-1Immobilizer system indicator light .......... 3-5
Indicator lights and warning lights .......... 3-4
Info switch ............................................ 3-15
L
License plate light bulb, replacing ........ 6-34
M
Main switch/steering lock ....................... 3-2
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system .................................................. 6-3
Matte color, caution ................................ 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-6
P
Panels, removing and installing .............. 6-7
Parking .................................................... 5-6
Part locations .......................................... 2-1
Pass switch........................................... 3-14
S
Safe-riding points ................................... 1-5
Safety information................................... 1-1
Seat....................................................... 3-20
Shock absorber assemblies,
adjusting ............................................. 3-22
Sidestand .............................................. 3-23
Spark plug, checking .............................. 6-9
Specifications ......................................... 8-1
Starting off .............................................. 5-3
Starting the engine.................................. 5-2
Start switch ........................................... 3-14
Steering, checking ................................ 6-26
Storage ................................................... 7-4
Storage compartments ......................... 3-21
T
Tail/brake light ...................................... 6-32
Throttle grip and cable, checking and
lubricating ........................................... 6-24
Throttle grip free play, checking ........... 6-17
Tires ...................................................... 6-18
Tool kit .................................................... 6-2
Troubleshooting .................................... 6-34
Troubleshooting charts ......................... 6-35
Turn signal indicator lights ...................... 3-4
Turn signal light bulb (rear), replacing... 6-33
Turn signal switch ................................. 3-14
V
Valve clearance..................................... 6-17
Vehicle identification number ................. 9-1
W
Wheel bearings, checking..................... 6-27
U2DME2E0.book Page 1 Tuesday, June 30, 2015 11:38 AM