2016 YAMAHA XJ6-N check engine

Periodic maintenance an d a djustment
6-46
6 En
gine overheatin g
WARNING
EWA10401
Do not remove the ra diator cap when the en gine an d ra diator are hot.
Scal din g hot flui d an d steam may b e blown out un der pressure, which
coul d cause serious injury. Be sure to wait until the eng ine has cooled.
 After removin g the ra diator cap retainin g b olt, place a thick rag , like a
towel, over the ra diator cap, an d then slowly rotate the cap counter-
clockwise to the d etent to allow any resi dual pressure to escape. When
the hissin g sound has stopped , press down on the cap while turnin g it
counterclockwise, an d then remove the cap.
TIP
If coolant is not available, tap water can be temporarily used instead, provided
that it is changed to the recommended coolant as soon as possible.
Wait until the engine
has cooled.
Check the coolant
level in the reservoir
and radiator.Add coolant.
(See TIP.)
The coolant level is
OK.
There is no leakage.
There is leakage.
The coolant level is
low.
Check the cooling
system for leakage.
Have a Yamaha
dealer check and
repair the cooling
system.
Start the engine. If the engine overheats again,
have a Yamaha dealer check and repair the cooling
system.
UB61E1E0.book Page 46 Wednesday, October 21, 2015 11:19 AM

Motorcycle care and stora ge
7-4
7
EAU26183
Stora ge
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the mo-
torcycle.
NOTICE
ECA10811
 Storin g the motorcycle in a
poorly ventilated room or cover-
in g it with a tarp, while it is still
wet, will allow water an d humi d-
ity to seep in and cause rust.
 To prevent corrosion, avoi d
d amp cellars, sta bles ( because
of the presence of ammonia)
an d areas where stron g chemi-
cals are stored .
Long-term
Before storing your motorcycle for sev-
eral months: 1. Follow all the instructions in the “Care” section of this chapter.
2. Fill up the fuel tank and add fuel stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to protect the cylinders, piston rings,
etc. from corrosion.a. Remove the spark plug caps and spark plugs.
b. Pour a teaspoonful of engine oil into each spark plug bore.
c. Install the spark plug caps onto the spark plugs, and then pla-
ce the spark plugs on the cylin- der head so that the electrodes
are grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder walls with oil.)
WARNING! To prevent d am-
a g e or injury from sparkin g,
make sure to groun d the
spark plu g electro des while
turnin g the en gine over.
[EWA10952]
e. Remove the spark plug caps
from the spark plugs, and then
install the spark plugs and the
spark plug caps.
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully char- ge it. Store it in a cool, dry place
and charge it once a month. Do
not store the battery in an exces-
sively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
6-33.
UB61E1E0.book Page 4 Wednesday, October 21, 2015 11:19 AM

10-1
10
Index
A
ABS (for ABS models) .......................... 3-14
ABS warning light (for ABS models)....... 3-5
Air filter element, replacing................... 6-16
Auxiliary light bulb, replacing ............... 6-38
B
Battery .................................................. 6-33
Brake and clutch levers, checking and
lubricating .......................................... 6-30
Brake and shift pedals, checking and lubricating .......................................... 6-29
Brake fluid, changing ........................... 6-26
Brake fluid level, checking ................... 6-25
Brake lever ........................................... 3-13
Brake lever free play, checking ............ 6-23
Brake light switches ............................. 6-23
Brake pedal .......................................... 3-13
Brake/tail light bulb, replacing ............. 6-39
C
Cables, checking and lubricating ......... 6-28
Care ........................................................ 7-1
Catalytic converter ............................... 3-17
Clutch lever .......................................... 3-12
Clutch lever free play, adjusting ........... 6-22
Coolant ................................................. 6-12
Coolant temperature warning light ......... 3-4
Cowling and panels, removing and installing ............................................... 6-7
D
Dimmer switch ..................................... 3-10
Drive chain, cleaning and lubricating ... 6-28
Drive chain slack .................................. 6-26
E
Engine break-in ...................................... 5-4
Engine idling speed .............................. 6-17
Engine oil and oil filter cartridge ............. 6-9
Engine serial number.............................. 9-1
Engine stop switch ............................... 3-11
Engine trouble warning light................... 3-5
F
Front and rear brake pads, checking ... 6-24
Front fork, checking ............................. 6-31
Fuel....................................................... 3-15
Fuel consumption, tips for reducing ...... 5-4
Fuel tank breather hose and overflow hose ................................................... 3-17
Fuel tank cap........................................ 3-15
Fuses, replacing ................................... 6-34
H
Handlebar position, adjusting .............. 3-20 Handlebar switches .............................. 3-10
Hazard switch ....................................... 3-11
Headlight bulb, replacing ...................... 6-36
Helmet holder ....................................... 3-19
High beam indicator light........................ 3-4
Horn switch........................................... 3-11
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system ............... 3-22
Immobilizer system ................................. 3-1
Immobilizer system indicator light .......... 3-6
Indicator lights and warning lights .......... 3-4
L
License plate light bulb, replacing ........ 6-40
M
Main switch/steering lock ....................... 3-2
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system .................................................. 6-3
Matte color, caution ................................ 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-6
N
Neutral indicator light.............................. 3-4
O
Oil level warning light .............................. 3-4
P
Parking .................................................... 5-5
Part locations .......................................... 2-1
Pass switch........................................... 3-10
S
Safety information................................... 1-1
Seat....................................................... 3-18
Shifting .................................................... 5-3
Shift pedal............................................. 3-12
Shock absorber assembly, adjusting ... 3-21
Sidestand .............................................. 3-22
Sidestand, checking and lubricating .... 6-30
Spark plugs, checking ............................ 6-8
Specifications ......................................... 8-1
Starting the engine.................................. 5-2
Start switch ........................................... 3-11
Steering, checking ................................ 6-32
Storage ................................................... 7-4
Storage compartment ........................... 3-20
Supporting the motorcycle ................... 6-40
Swingarm pivots, lubricating ................ 6-31
T
Throttle grip and cable, checking and lubricating ........................................... 6-29
UB61E1E0.book Page 1 Wednesday, October 21, 2015 11:19 AM