2016 YAMAHA XENTER 125 wheel

[x] Cancel search: wheel

manual transmission key battery alarm bolt pattern trip computer inflation pressure

Load previous 8 pages

Page 61 of 84

YAMAHA XENTER 125 2016 Owners Manual Periodic maintenance and adjustment6-26
1
2
3
4
567
8
9
10
11
12
EAU45512
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checke

Page 70 of 84

YAMAHA XENTER 125 2016 Owners Manual 7-1
1
2
3
4
5
67
8
9
10
11
12
Scooter care and storage
EAU37834
Matte color cautionNOTICE
ECA15193
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
ad

7-1
1
2
3
4
5
67
8
9
10
11
12
Scooter care and storage
EAU37834
Matte color cautionNOTICE
ECA15193
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin-ished parts.
EAU26096
CareWhile the open design of a scooter re-
veals the attractiveness of the technol-
ogy, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed
on a car, however, it detracts from the
overall appearance of a scooter. Fre-
quent and proper care does not only
comply with the terms of the warranty,
but it will also keep your scooter looking
good, extend its life and optimize its
performance.
Before cleaning 1. Cover the muffler outlet with a plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly in-
stalled.
3. Remove extremely stubborn dirt, like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod- ucts onto seals, gaskets and wheel
axles. Always rinse the dirt and de-
greaser off with water.
Cleaning
NOTICE
ECA10784

Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.

Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
off any detergent residue using
U53BE1E0 1 ページ２０１５年９月１５日　火曜日　午後１時４８分

Page 71 of 84

YAMAHA XENTER 125 2016 Owners Manual Scooter care and storage
7-2
1
2
3
4
5
678
9
10
11
12
plenty of water, as it is harmful
to plastic parts.

Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or

Scooter care and storage
7-2
1
2
3
4
5
678
9
10
11
12
plenty of water, as it is harmful
to plastic parts.

Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid- den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride in
the rain, near the sea or on
salt-sprayed roads.TIPSalt sprayed on roads in the winter may
remain well into spring. 1. Clean the scooter with cold water and a mild detergent after the en-
gine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.
[ECA10792]
2. Apply a corrosion protection spray on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
Cleaning the windshieldAvoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield with
a cloth or sponge dampened with a mild
detergent, and then wash it off thor-
oughly with water. For additional clean-
ing, use Yamaha Windshield Cleaner
or another high-quality windshield
cleaner. Some cleaning compounds for
plastics may leave scratches on the
windshield. Before using such clean-
ers, test an area of the windshield
which does not affect your visibility and
which cannot be easily recognized.
U53BE1E0 2 ページ２０１５年９月１５日　火曜日　午後１時４８分

Page 73 of 84

YAMAHA XENTER 125 2016 Owners Manual Scooter care and storage
7-4
1
2
3
4
5
678
9
10
11
12
EAU36564
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure

Scooter care and storage
7-4
1
2
3
4
5
678
9
10
11
12
EAU36564
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the scoot-
er.NOTICE
ECA10821

Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your scooter for several
months: 1. Follow all the instructions in the “Care” section of this chapter. 2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro- tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10952]
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0  C (30 F) or more than 30
 C (90 F)]. For more information
on storing the battery, see page
6-26.TIPMake any necessary repairs beforestoring the scooter.
U53BE1E0 4 ページ２０１５年９月１５日　火曜日　午後１時４８分

Page 74 of 84

YAMAHA XENTER 125 2016 Owners Manual 8-1
1
2
3
4
5
6
78
9
10
11
12
Specifications
EAU72940
Dimensions:Overall length: 1990 mm (78.3 in)
Overall width: 690 mm (27.2 in)
Overall height: 1135 mm (44.7 in)
Seat height:
785 mm (30.9 in)
Wheel

Page 75 of 84

YAMAHA XENTER 125 2016 Owners Manual Specifications
8-2
1
2
3
4
5
6
789
10
11
12
Manufacturer/model: DURO / DM1157FRear tire:Type:Tubeless
Size: 120 / 80 - 16M/C 60P
Manufacturer/model:
DURO / DM1157Loading:Maximum load:179 kg (395 lb)
*

Page 79 of 84

YAMAHA XENTER 125 2016 Owners Manual Index
AAcceleration and deceleration ................... 5-2
Air filter and V-belt case air filter
elements ................................................ 6-16
Auxiliary light bulb, replacing .....

Index
AAcceleration and deceleration ................... 5-2
Air filter and V-belt case air filter
elements ................................................ 6-16
Auxiliary light bulb, replacing ................... 6-29BBattery ..................................................... 6-26
Brake fluid, changing ............................... 6-23
Brake fluid level, checking ....................... 6-22
Brake lever, front ....................................... 3-7
Brake lever, rear ........................................ 3-8
Brake levers, lubricating .......................... 6-24
Brake pads and shoes, checking............. 6-21
Braking ...................................................... 5-3CCables, checking and lubricating ............. 6-23
Care ........................................................... 7-1
Carrier...................................................... 3-14
Catalytic converter ................................... 3-10
Centerstand, checking and lubricating .... 6-24
Coolant .................................................... 6-14
Coolant temperature warning light............. 3-2
Cowling and panels, removing and installing .................................................. 6-8DDimmer switch ........................................... 3-7EEngine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-17
Engine oil ................................................. 6-11
Engine serial number................................. 9-1
Engine trouble warning light ...................... 3-3FFinal transmission oil ............................... 6-13 Front brake lever free play, checking ...... 6-20
Front fork, checking................................. 6-25
Fuel ........................................................... 3-9
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap............................................. 3-8
Fuses, replacing ...................................... 6-28
HHandlebar switches ................................... 3-7
Headlight bulb, replacing......................... 6-28
High beam indicator light........................... 3-2
Horn switch ............................................... 3-7IIdentification numbers ............................... 9-1
Indicator lights and warning lights ............. 3-2LLicense plate light ................................... 6-32
Luggage holder ....................................... 3-14MMain switch/steering lock .......................... 3-1
Maintenance and lubricatio
n, periodic....... 6-5
Maintenance, emission control system ..... 6-4
Matte color, caution ................................... 7-1
Model label ................................................ 9-2
Multi-function display................................. 3-3PParking ...................................................... 5-4
Part locations ............................................ 2-1
Passenger footrest .................................. 3-11RRear brake lever free play, adjusting ...... 6-20SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-11 Shock absorber assembly .......................3-13
Spark plug, checking ...............................6-10
Specifications.............................................8-1
Starting off .................................................5-2
Starting the engine.....................................5-1
Start switch ................................................3-7
Steering, checking ...................................6-26
Storage ......................................................7-4
Storage compartments ............................3-12
TTail/brake light ......................................... 6-30
Throttle grip and cable, checking and
lubricating ..............................................6-24
Throttle grip free play, checking...............6-17
Tires .........................................................6-18
Tool kit .......................................................6-2
Troubleshooting .......................................6-32
Troubleshooting charts ............................6-33
Turn signal indicator lights .........................3-2
Turn signal light bulb (front), replacing ....6-30
Turn signal light bulb (r ear), replacing .....6-31
Turn signal switch ......................................3-7VValve clearance .......................................6-18
Vehicle identificat ion number .....................9-1WWheel bearings, checking........................6-26
Wheels .....................................................6-20
U53BE1E0 1 ページ２０１５年９月１５日　火曜日　午後１時４８分

Page: < prev 1-8 9-16

fuel tank capacity water pump warning lights adblue reset reset infotainment system engine coolant