2016 YAMAHA WR 450F run flat

CHASSIS
4-2
• Under a stony or a hard road condition, the tire pressure should be hi gher to prevent a flat
tire.
EAS2GC1140FRONT FORK SETTING
The front fork setting should be made depend-
ing on the rider’s feeli ng of an actual run and
the circuit conditions.
The front fork setting includes the following
three factors:
1. Setting of air spring characteristics • Change the fork oil amount.
2. Setting of spring preload • Change the spring.
3. Setting of damping force
• Change the compression damping force.
• Change the rebound damping force.The spring acts on the load and the damping
force acts on the cushion travel speed.
EAS2GC1141CHANGE IN AMOUNT AND CHARACTERIS-
TICS OF FORK OIL
Damping characteristic near the final stroke
can be changed by changing the fork oil
amount.
EWA
WARNING
Adjust the oil amount in 5 cm3 (0.2 US oz,
0.2 Imp.oz) increments or decrements. Too
small oil amount causes the front fork to
produce a noise at full rebound or the rider
to feel some pressure on his hands or body.
Alternatively, too large oil amount will
cause the air spring characteristics to have
a tendency to be stiffer with the consequent
deteriorated performance and characteris-
tics. Therefore, adjust the front fork within
the specified range.
EAS2GC1142SETTING OF SPRING AFTER REPLACE-
MENT
As the front fork setting can be easily affected
by the rear suspension, take care so that the
front and the rear are balanced (in position etc.)
when setting the front fork.
1. Use of soft spring
• Change the rebound damping force.Turn out one or two clicks.
• Change the compression damping force.
Turn in one or two clicks.
TIP
Generally a soft spring gives a soft riding feel-
ing. Rebound damping tends to become stron-
ger and the front fork may sink deeply over a
series of gaps.
2. Use of stiff spring• Change the rebound damping force.
Turn in one or two clicks.
• Change the compression damping force. Turn out one or two clicks.
Extent of adjustment
100–120 kPa (1.00–1.20 kgf/cm
2,
15–18 psi)
Standard oil amount 345 cm
3 (11.66 US oz, 12.14
lmp.oz)
Extent of adjustment 300–365 cm
3 (10.14–12.34 US
oz, 10.58–12.87 Imp.oz)
A. Air spring characteristics in relation to oil amount change
B. Load
C. Stroke
1. Max. oil amount
2. Standard oil amount
3. Min. oil amount

FRONT WHEEL
5-5
EAS2GC1155REMOVING THE FRONT WHEEL
1. Use a suitable stand to raise the front wheel off the ground.
EWA
WARNING
Securely support the vehicle so that there is
no danger of it falling over.
2. Remove:• Front wheel
EAS2GC1156CHECKING THE FRONT WHEEL
1. Check:• Front wheel axleRoll the front wheel axle on a flat surface.
Bends  Replace.
EWA
WARNING
Do not attempt to straighten a bent wheel
axle.
2. Check:
•Tire(s)
• Front wheelDamage/wear  Replace.
Refer to “CHECKING THE TIRES” on page
3-36 and “CHECKING THE WHEELS” on
page 3-37.
3. Check: • Spokes
Bend/damage  Replace.
Loose  Tighten.
Tap the spokes with a screwdriver.
TIP
A tight spoke will emit a clear, ringing tone; a
loose spoke will sound flat.
4. Tighten: • Spokes
Refer to “CHECKING AND TIGHTENING
THE SPOKES” on page 3-36.
TIP
After tightening the spokes, measure the wheel
runout.
5. Measure:• Wheel radial runout “a”
• Wheel lateral runout “b”Out of specification  Repair/replace.
6. Check: •CollarsDamage/wear  Replace.
7. Check: • BearingFront wheel turns roughly or is loose  Re-
place the wheel bearings.
• Oil seals Damage/wear  Replace.
Spokes
2.5 Nm (0.25 m·kgf, 1.8 ft·lbf)
Radial wheel runout limit 2.0 mm (0.08 in)
Lateral wheel runout limit 2.0 mm (0.08 in)
T R..
a b

CRANKSHAFT ASSEMBLY AND BALANCER SHAFT
6-75
EAS2GC1318REMOVING THE BALANCER SHAFT
1. Remove:• Balancer shaft “1”
TIP
Remove the balancer shaft with its flat side “a”
facing the crankshaft.
EAS2GC1319REMOVING THE CRANKSHAFT ASSEMBLY
1. Remove:• Crankshaft assembly “1”
TIP
Remove the crankshaft assembly by using the
crankcase separating tool “2”.
EAS2GC1320CHECKING THE CRANKSHAFT ASSEMBLY
1. Measure:• Crankshaft runoutOut of specification  Replace the crank-
shaft, bearing or both.
TIP
Turn the crankshaft slowly.
2. Measure: • Big end side clearance “a”Out of specification  Replace the big end
bearing, crankshaft pin, or connecting rod.
3. Measure: • Crank assembly width “a”Out of specification  Replace the crank-
shaft.
Crankcase separating tool
90890-04152
YU-A9642
1
a
2
1
Runout limit 0.030 mm (0.0012 in)
Big end side clearance 0.150–0.450 mm (0.0059–0.0177
in)
Crank assembly width 61.93–62.00 mm (2.438–2.441 in)