2016 YAMAHA WR 450F clutch

GENERATOR AND STARTER CLUTCH
6-66
EAS2GC1308INSTALLING THE STARTER CLUTCH
1. Install:• Stator “1”
• Stator bolt “2”
• Crankshaft position sensor “3”
• Holder “4”
• Crankshaft position sensor bolt “5”
TIP
• Pass the stator coil lead between ribs “a”, and put it in part “b” so that there is no slack.
• Pass crankshaft sensor lead “c” over stator
coil lead “d”.
• Pass the crankshaft sensor lead outside of rib “a” and place the excess end next to boss “e”.
• Make sure that the end surface of holder “f” does not get caught on rib “a”.
• Place the stator coil lead and crankshaft sen-
sor lead inside the U-shaped space “g”of the
holder.
• Tighten the stator bolt using the T25 bit.
• Apply the sealant to the grommet of the AC
magneto lead. 2. Install
• Starter clutch drive gear “1”
TIP
Apply the engine oil on the starter clutch drive
gear inner circumference.
Stator bolt
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
LOCTITE®
Crankshaft position sensor bolt 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Yamaha bond No. 1215 90890-85505
(Three bond No.1215®)
T R..
T R..
g
d
c
ea
a
b
f
LT

GENERATOR AND STARTER CLUTCH
6-67
3. Install:• Starter clutch “1”To generator rotor “2”.
EAS2GC1309INSTALLING THE GENERATOR
1. Install:
• Woodruff key “1”
• Generator rotor “2”
TIP
• Clean the contact surfaces of the tapered por-tions of the crankshaft and generator rotor.
• When installing the woodruff key, make sure that its flat surface “a” is in parallel with the
crankshaft center line “b”.
• When installing the generator rotor, align the keyway “c” of the generator rotor with the
woodruff key.
2. Install: • Washer
• Generator rotor nut “1” 3. Install:
• Starter idle gear shaft “1”
• Bearing “2”
• Starter idle gear 2 “3”
TIP
Apply the engine oil on the starter idle gear
shaft, bearing and idle gear inner circumfer-
ence.
4. Install:
• Dowel pin
• Crankcase cover gasket
• Left crankcase cover “1”
• Lead holder “2”
• Crankcase cover bolt
• Neutral switch lead “3”
TIP
• Pass the AC magneto lead “4” under the left crankcase cover “a” as shown.
• Tighten the bolts in stage, using a crisscross
pattern.
Starter clutch bolt
16 Nm (1.6 m·kgf, 12 ft·lbf)
LOCTITE®
Generator rotor nut 65 Nm (6.5 m·kgf, 47 ft·lbf)
21
LT
T R..
2
C
1 1
1a
b
T R..
Crankcase cover bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
1
1
2 1
2
3
New
T R..

GENERATOR AND STARTER CLUTCH
6-68
5. Install:• Washer “1”
• Damper assembly “2”
• Washer “3”
TIP
Apply the engine oil to the shaft and washers.
6. Install:• Cover (damper assembly) “1”
• Bracket “2”
•Bolt “3”
TIP
Install the cover (damper assembly) with its
mark “a” facing upward. Bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
4
1 a
1
2
3
2
1
2
3
T R..
1a3
3
2

CRANKCASE
6-69
EAS2GC1310
CRANKCASE
Separating the crankcase
OrderPart name Q’tyRemarks
Engine Refer to “ENGINE REMOVAL” on page 6-1.
Piston Refer to “CYLINDER AND PISTON” on page
6-31.
Balancer Refer to “OIL PUMP AND BALANCER
GEAR” on page 6-57.
Kick shaft assembly Refer to “KICKSTATER” on page 6-50.
Segment Refer to “SHIFT SHAFT” on page 6-53.
Stator Refer to “GENERATOR AND STARTER
CLUTCH” on page 6-63.
1 Timing chain guide (exhaust side) 1
2 Timing chain guide stopper plate 1
3 Timing chain 1
4 Bolt [L = 45 mm (1.77 in)] 6
5 Bolt [L = 60 mm (2.36 in)] 4
6 Bolt [L = 75 mm (2.95 in)] 2
7 Right crankcase 1
8 Left crankcase 1
9 Dowel pin 2
10 Nm (1.0 m kgf, 7.2 ft Ibf)T.R.12 Nm (1.2 m kgf, 8.7 ft Ibf)T.R.
3
1
5
2 6410
5
5
4
4 4 46
9 7
8
11
9
LT
10 Nm (1.0 m kgf, 7.2 ft Ibf)T.R.
12 Nm (1.2 m kgf, 8.7 ft Ibf)T.R.
12 Nm (1.2 m kgf, 8.7 ft Ibf)T.R.
LT

WATER PUMP
7-4
EAS2GC1332
WATER PUMP
Removing the water pump
OrderPart name Q’tyRemarks
Coolant Drain.
Refer to “CHANGING THE COOLANT” on
page 3-10.
Engine oil Drain.
Refer to “CHANGING THE ENGINE OIL” on
page 3-17.
Right crankcase cover Refer to “CLUTCH” on page 6-41.
1 Water pump housing 1
2 Dowel pin 2
3Gasket 1
4Collar 1
5Pin 1
6 Impeller shaft assembly 1
7 Oil seal 1
8 Bearing 1
9 Oil seal 1
For installation, reverse the removal proce-
dure.
LS
LS
7
6
2 2
3
1
854
New
New
New
E
9
New
E
10 Nm (1.0 m kgf, 7.2 ft Ibf)T.R.
10 Nm (1.0 m kgf, 7.2 ft Ibf)T.R.

ELECTRIC STARTING SYSTEM
9-7
1. Joint connector
2. Joint connector
3. Joint connector
7. Main relay
9. Battery
10.Frame ground
11.Starter relay
12.Main fuse
13.Starter motor
14.Starter relay diode
22.ECU (engine control unit)
30.Joint connector
36.Engine stop switch
37.Neutral switch
38.Diode
39.Starting circuit cut-off relay
40.Clutch switch
41.Start switch
48.Frame ground
50.Negative battery lead

ELECTRIC STARTING SYSTEM
9-8
EAS2GC1362STARTING CIRCUIT CUT-OFF SYSTEM OPERATION
If the meter light comes on, the starter motor can only operate if at least one of the following condi-
tions is met:
• The transmission is in neutral (the neutral switch is closed).
• The clutch lever is pulled to the handlebar (the clutch switch is closed).
The starting circuit cut-off relay prevents the starter motor from operating when neither of these con-
ditions has been met. In this instance, the starting ci rcuit cut-off relay is open so current cannot reach
the starter motor. When at least one of the above conditions has been met the starting circuit cut-off
relay is closed and the engine can be started by pressing the start switch.

ELECTRIC STARTING SYSTEM
9-9
a. WHEN THE TRANSMISSION IS IN NEU-TRAL
b. WHEN THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR
1. Battery
2. Main fuse
3. Main relay
4. Starting circuit cut-off relay
5. Start switch
6. Diode
7. Clutch switch
8. Neutral switch
9. Starter relay
10.Starter motor