2016 YAMAHA VMAX set clock

Instrument and control functions
3-8
3
Shift timin
g in dicator li ght
The shift timing indicator light works
with the tachometer to inform the rider
of engine speed. See “Select mode”
on page 3-10 for an explanation on
how to set this indicator light.
EAU4658G
Multi-function display
WARNING
EWA12313
Be sure to stop the vehicle before
makin g any settin g chan ges to the
multi-function display. Chan gin g
settin gs while ri din g can distract the
operator an d increase the risk of an
acci dent.A “SELECT” button and a “RESET”
button are located on the handlebar
holder. These buttons allow you to
control or change the settings in the
multi-function display. The multi-function display is set to the
Normal mode every time the key is
turned to “ON”.
Normal mo
de
The following functions are available in
the Normal mode:  odometer
 clock
 two tripmeters
 fuel reserve tripmeter
 fuel meter
 transmission gear indicator
 coolant temperature meter
 self-diagnosis device1. Multi-function display
1
1. “SELECT” button
2. “RESET” button
12
U2CEE1E0.book Page 8 Thursday, November 19, 2015 10:32 AM

Instrument and control functions
3-9
3
The odometer shows the total distance
traveled by the vehicle.
The tripmeters show the distance trav-
eled since they were last reset.
The fuel reserve tripmeter shows the
distance traveled on the fuel reserve.
The clock displays time in 12-hour for-
mat.
TIPThe odometer will lock at 999999. 
The tripmeters will reset and con-
tinue counting after 9999.9 is
reached.
 For the UK: to switch between ki-
lometers and miles, press “SE-
LECT” for two seconds.
TripmetersTurn the key to “ON”. Push “SELECT”
to switch the display between the trip-
meters “TRIP-1” and “TRIP-2” in the
following order:
TRIP-1 → TRIP-2 → TRIP-1
When the fuel amount in the fuel tank
decreases to 3.9 L (1.03 US gal,
0.86 Imp.gal), the fuel level warning
light comes on, and the tripmeter auto-
matically changes to the fuel reserve
tripmeter “TRIP-F” and starts counting
the distance traveled from that point. In
that case, push “SELECT” to switch
the display in the following order:
TRIP-F → TRIP-1 → TRIP-2 → TRIP-F
If you continue to ride the vehicle after
the fuel reserve tripmeter “TRIP-F” ap-
pears, the fuel meter and fuel level
warning indicator “ ” start flashing. To reset a tripmeter, select it by push-
ing “SELECT”, and then push “RESET”
for one second.
The fuel reserve tripmeter can be reset
manually, or after refueling and travel-
ing 5 km (3 mi), it will reset automatical-
ly and disappear from the display.
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The displayed fuel
level decreases from “F” (full) towards
“E” (empty) as the fuel level decreases.
When the amount of fuel decreases to
approximately 3.9 L (1.03 US gal,
0.86 Imp.gal), the fuel level warning
light comes on. If this occurs, refuel as
soon as possible.
If you continue to ride the vehicle after
the fuel reserve tripmeter “TRIP-F” ap-
pears, the fuel meter and the fuel level
warning indicator “ ” start flashing.
Transmission gear indicatorThis indicator shows the selected gear.
The neutral position is indicated
by “ ” and by the neutral indicator
light.
1. Odometer
2. Clock
3. Tripmeter/fuel reserve tripmeter
4. Coolant temperature warning indicator “ ”
5. Coolant temperature meter
6. Transmission gear indicator
7. Fuel level warning indicator “ ”
8. Fuel meter
123
865
7
4
U2CEE1E0.book Page 9 Thursday, November 19, 2015 10:32 AM

Instrument and control functions
3-10
3
Coolant temperature meter
The coolant temperature meter indi-
cates the temperature of the coolant.
The coolant temperature varies with
changes in the weather and engine
load. If the coolant temperature meter
and the coolant temperature warning
indicator flash, stop the vehicle and let
the engine cool. (See page 6-42.)NOTICE
ECA10022
Do not continue to operate the en-
g
ine if it is overheatin g.Select mo de
The various functions of this multi-
function display are adjusted in the Se-
lect mode.TIP The transmission must be in neu-
tral to change settings in this mo-
de.
 Shifting the transmission into gear
saves all settings made, then can-
cels the Select mode and displays
the Normal mode in all screens. 
Depending on the screen, pushing
“RESET” saves settings or can-
cels the Select mode to display
the Normal mode.
Push and hold “SELECT” and “RE-
SET” for three seconds to enter the Se-
lect mode.
The following items can be set/adjust-
ed in this mode:
 brightness
 shift timing indicator light
 clock
 stopwatch
 countdown clock
 system status
 maintenance countersTIPTo return to the Normal mode, push
“SELECT” to scroll to “ ”, then push
“RESET”.
Adjusting the brightnessThis function allows you to adjust the
brightness of the tachometer panel
and speedometer (“Meter panel”), the
tachometer needle (“Needle”), and the
multi-function display (“Display”).
1. Push “SELECT” to highlight “Brightness”.
2. Push “RESET”, then push “SE- LECT” to scroll through the func-
tions and to highlight an item.
3. Push “RESET”; the brightness lev- el segments for the selected item
starts flashing.
4. Push “SELECT” to highlight the desired brightness level.
5. Push “RESET” to set the bright- ness level.
U2CEE1E0.book Page 10 Thursday, November 19, 2015 10:32 AM

Instrument and control functions
3-13
3 3. Push “SELECT” to highlight the
desired brightness level.
4. Push “RESET” to set the selected brightness level.
5. Push “RESET” to return to the pre- vious menu.
6. Push “SELECT” to scroll to “ ”, then push “RESET”. This allows
you to select another item in the
menu.
Setting the clock
1. Push “SELECT” to highlight “Dis- play”.
2. Push “RESET”; the following screen is displayed.
3. Push “RESET” and the hour digits start flashing.
4. Push “SELECT” to increment the hours. 5. Push “RESET”, and the minute
digits start flashing.
6. Push “SELECT” to increment the minutes.
7. Push “RESET” to start the clock.
8. Push “RESET” again to return to the previous menu.
Resetting all the brightness and shift
timing indicator light functionsThis resets all settings made to the
brightness and shift timing indicator
light functions. 1. Push “SELECT” to highlight “Dis- play”.
2. Push “RESET”.
3. Push “SELECT” to highlight “All reset”.
4. Push “RESET”, then push “SE- LECT” to highlight “Yes”. 5. Push “RESET” to reset the bright-
ness and shift timing light indica-
tor values to the factory setting.
The display returns to the Normal
mode.
TIPTo perform further multi-function dis-
play settings, enter the Select mode
again by pushing and holding “SE-
LECT” and “RESET” for three seconds.Using the stopwatchThe stopwatch can be activated as fol-
lows.1. Push “SELECT” to highlight “Stopwatch”.
2. Push “RESET”.
3. Push “SELECT” to highlight “Stopwatch”.
U2CEE1E0.book Page 13 Thursday, November 19, 2015 10:32 AM

Instrument and control functions
3-14
3
4. Push “RESET”.
The multi-function display chang-
es to the Normal mode and the
stopwatch is displayed in place of
the clock.
5. Push “SELECT” to start the stop- watch.
6. Push the start switch “ ” or “SE- LECT” to stop the stopwatch.
7. Push “RESET” to reset the stop- watch.
TIPIf neither “SELECT” nor “RESET”
are pushed for one minute, the
screen automatically changes to
the Normal mode.
 Pushing “RESET” for two seconds
changes the screen to the Normal
mode. 
To perform further multi-function
display settings, enter the Select
mode again by pushing and hold-
ing “SELECT” and “RESET” for
three seconds.
Using the countdown clockThe countdown clock can be activated
as follows.
1. Push “SELECT” to highlight “Stopwatch”.
2. Push “RESET”.
3. Push “SELECT” to highlight “Countdown”.
4. Push “RESET”. The multi-function display changes to the Normal
mode, the stopwatch is displayed
in place of the clock, and the
transmission gear indicator
changes to the countdown clock. 5. Push “SELECT” or shift into gear
and the countdown clock starts
counting down from “5”. Simulta-
neously, the shift timing indicator
light flashes according to the
number displayed (i.e., when “5” is
displayed, the indicator light flash-
es five times, when “4” is dis-
played, the indicator light flashes
four times, etc.). The stopwatch
starts counting when the count-
down clock finishes counting.
6. Push the start switch “ ” or “SE- LECT” to stop the countdown
clock.
7. Push “RESET” to reset the count- down clock and stopwatch.
8. Repeat steps 5–7, or push “RE-
SET” again for two seconds to en-
ter the Normal mode.
TIPTo perform further multi-function dis-
play settings, be sure the transmis-
sion is in neutral, then enter the Select
mode again by pushing and holding
“SELECT” and “RESET” for three sec-
onds.
U2CEE1E0.book Page 14 Thursday, November 19, 2015 10:32 AM

Instrument and control functions
3-15
3 Checking and resetting the system sta-
tusThe status/readings of the following
items are displayed, and the tripmeters
can be reset.
 tripmeters and odometer
 fuel consumption
 air intake temperature
 throttle opening positionTIPThe “System status” menu cannot
be entered if the fuel level warning
light or coolant temperature warn-
ing light is on.
 If, when the engine is running
while the system status menu is
displayed, the fuel level warning
light or coolant temperature warn-
ing light comes on, the Normal
mode is automatically displayed.1. Push “SELECT” to highlight “Sys-
tem status”, then push “RESET”. 2. Push “SELECT” to highlight
“Yes”, then push “RESET”. (High-
lighting “No” and pushing “RE-
SET” returns to the previous
menu.)
The display changes to the status
screen. Push “SELECT” and the various trip-
meters and the odometer are dis-
played in the following order:
(TRIP-F)
→ TRIP-1 → TRIP-2 → ODO
→ (TRIP-F)
Push “RESET” to reset a tripmeter.
TIP For the UK: push “SELECT” for
two seconds to switch between
kilometers and miles.
 Pushing “RESET” displays the
Normal mode for five seconds.
Pushing “SELECT” and “RESET”
for three seconds, changes the
display to the Normal mode.
 To perform further multi-function
display settings, enter the Select
mode again by pushing and hold-
ing “SELECT” and “RESET” for
three seconds.Resetting the maintenance countersThis function allows you to reset the
maintenance counters for the tires, the
engine oil, and an item of your choice.
1. Push “SELECT” to highlight “Maintenance”.
1. Odometer/tripmeter/fuel reserve tripmeter
2. Clock
3. Instantaneous fuel consumption
4. Throttle opening position display
5. Transmission gear indicator
6. Air intake temperature display
12 3
654
U2CEE1E0.book Page 15 Thursday, November 19, 2015 10:32 AM