2016 YAMAHA VMAX engine coolant

Operation and important rid ing points
5-1
5
EAU15952
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10272
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which coul d cause an acci dent
or injury.
EAU48712
TIPThis model is equipped with:  a lean angle sensor to stop the en-
gine in case of a turnover. In this
case, the display will indicate error
code 30, but this is not a malfunc-
tion. Turn the key to “OFF” and
then to “ON” to clear the error co-
d e . F ai l in g to do s o wi ll pr e v e nt the
engine from starting even though
the engine will crank when push-
ing the start switch.
 an engine auto-stop system. The
engine stops automatically if left
idling for 20 minutes. If the engine
stops, simply push the start
switch to restart the engine.
EAU51693
Startin g the en gineIn order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
 The transmission is in the neutral
position.
 The transmission is in gear with
the clutch lever pulled and the
sidestand up.
See page 3-32 for more informa-
tion.
1. Turn the key to “ON” and make sure that the engine stop switch is
set to “ ”.
The following warning lights and
indicator lights should come on for
a few seconds, then go off. Oil level warning light
 Fuel level warning light
 Coolant temperature warning
light
 Engine trouble warning light
 Shift timing indicator light
 Immobilizer system indicator
light
U2CEE1E0.book Page 1 Thursday, November 19, 2015 10:32 AM

Periodic maintenance an d a djustment
6-16
6
7. Check the oil check bolt gasket
and the oil filler bolt gasket for
damage, and replace them if nec-
essary.
8. Refill with the recommended final gear oil until it flows out of the oil
check bolt hole.
9. Install the oil check bolt, the oil fill- er bolt and their gasket, and then
tighten the bolts to the specified
torques. 10. Install the final gear case breather
cap by installing the washer and
bolt, and then tighten the bolt to
the specified torque.
11. Check the final gear case for oil leakage. If oil is leaking, check for
the cause.
EAU20071
CoolantThe coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU46694
To check the coolant level1. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion.TIPThe coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.
 Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.2. Check the coolant level in the
coolant reservoir.TIPThe coolant should be between the mi-
nimum and maximum level marks.
1. Final gear oil check bolt
2. GasketRecommen ded final gear oil:
Yamaha genuine shaft drive gear oil
SAE 80W-90 API GL-5
Oil quantity:
0.30 L (0.32 US qt, 0.26 Imp.qt)
2
1
Tightenin g torques:
Final gear oil check bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Final gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
Ti ghtenin g torque:
Final gear case breather cap bolt: 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
U2CEE1E0.book Page 16 Thursday, November 19, 2015 10:32 AM

Periodic maintenance an d a djustment
6-17
6
3. If the coolant is at or below the mi-nimum level mark, remove the
coolant reservoir cap guard by re-
moving the bolt, and then remove
the reservoir cap. WARNING! Re-
move only the coolant reservoir
cap. Never attempt to remove
the ra diator cap when the en-
g ine is hot.
[EWA15162]
4. Add coolant to the maximum level
mark, and then install the reservoir
cap. NOTICE: If coolant is not
availa ble, use distille d water or
soft tap water instead . Do notuse har
d water or salt water
since it is harmful to the en gine.
If water has been used instead
of coolant, replace it with cool-
ant as soon as possi ble, other-
wise the coolin g system will not
b e protecte d a gainst frost an d
corrosion. If water has been
a dde d to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possi ble, otherwise the
effectiveness of the coolant will
b e re duce d.
[ECA10473]
5. Install the coolant reservoir cap
guard by installing the bolt.
EAU46426
To chan ge the coolant
1. Place the vehicle on a level surfa- ce and let the engine cool if neces-
sary.
2. Remove cowling A. (See page 6-8.) 3. Remove the right air intake duct
by removing the bolts.
4. Place a container under the en- gine to collect the used coolant.
5. Remove the radiator cap. WARNING! Never attempt to re-
move the ra diator cap when the
en gine is hot.
[EWA10382]
1. Coolant reservoir cap
2. Coolant reservoir cap guard
3. Bolt
4. Maximum level mark
5. Minimum level mark
2
1
5
4
3
Coolant reservoir capacity (up to
the maximum level mark):
0.27 L (0.29 US qt, 0.24 Imp.qt)
1. Bolt
2. Right air intake duct
1 1
2
U2CEE1E0.book Page 17 Thursday, November 19, 2015 10:32 AM

Periodic maintenance an d a djustment
6-19
6 14. Install the coolant reservoir cap,
and then install the reservoir cap
guard by installing the bolt.
15. Install the radiator cap.
16. Start the engine, let it idle for sev- eral minutes, and then turn it off.
17. Remove the radiator cap to check the coolant level in the radiator. If
necessary, add sufficient coolant
until it reaches the top of the radi-
ator, and then install the radiator
cap.
18. Check the coolant level in the res- ervoir. If necessary, remove the
coolant reservoir cap guard and the cap, add coolant to the maxi-
mum level mark, and then install
the cap and the cap guard.
19. Start the engine, and then check the vehicle for coolant leakage. If
coolant is leaking, have a Yamaha
dealer check the cooling system.
20. Install the right air intake duct by installing the bolts.
21. Install the cowling.
EAU36765
Air filter elementThe air filter element must be replaced
at the intervals specified in the periodic
maintenance and lubrication chart.
Have a Yamaha dealer replace the air
filter element.
Antifreeze/water mixture ratio: 1:1
Recommen ded antifreeze:
High-quality ethylene glycol anti-
freeze containing corrosion inhibi-
tors for aluminum engines
Coolant quantity:
Radiator (including all routes):3.75 L (3.96 US qt, 3.30 Imp.qt)
Coolant reservoir (up to the maxi-
mum level mark): 0.27 L (0.29 US qt, 0.24 Imp.qt)
U2CEE1E0.book Page 19 Thursday, November 19, 2015 10:32 AM

Periodic maintenance an d a djustment
6-42
6
En
gine overheatin g
WARNING
EWAT1041
Do not remove the ra diator cap when the en gine an d ra diator are hot. Scal din g hot flui d an d steam may be
b lown out un der pressure, which coul d cause serious injury. Be sure to wait until the en gine has coole d.
 Place a thick rag , like a towel, over the ra diator cap, an d then slowly rotate the cap counterclockwise to the
d etent to allow any resi dual pressure to escape. When the hissin g soun d has stopped , press down on the cap
while turnin g it counterclockwise, an d then remove the cap.TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended cool-
ant as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U2CEE1E0.book Page 42 Thursday, November 19, 2015 10:32 AM

Specifications
8-1
8
Dimensions:Overall length:2395 mm (94.3 in)
Overall width:
820 mm (32.3 in)
Overall height: 1190 mm (46.9 in)
Seat height: 775 mm (30.5 in)
Wheelbase:
1700 mm (66.9 in)
Ground clearance: 140 mm (5.51 in)
Minimum turning radius: 3.5 m (11.48 ft)Wei ght:Curb weight:
310 kg (683 lb)Engine:Combustion cycle:
4-stroke
Cooling system: Liquid cooled
Valve train: DOHC
Cylinder arrangement:
V-type
Number of cylinders: 4-cylinder
Displacement: 1679 cm³
Bore × stroke:
90.0 × 66.0 mm (3.54 × 2.60 in) Compression ratio:
11.3 : 1
Starting system: Electric starter
Lubrication system:
Wet sump
Engine oil:Recommended brand:
YAMALUBE
SAE viscosity grades:
10W-40
Recommended engine oil grade: API service SG type or higher, JASO
standard MA
Engine oil quantity: Oil change:
4.30 L (4.55 US qt, 3.78 Imp.qt)
With oil filter removal: 4.70 L (4.97 US qt, 4.14 Imp.qt)Final gear oil:Type:
Yamaha genuine shaft drive gear oil SAE 80W-90 API GL-5
Quantity:
0.30 L (0.32 US qt, 0.26 Imp.qt)Coolant quantity:Coolant reservoir (up to the maximum level
mark):0.27 L (0.29 US qt, 0.24 Imp.qt)
Radiator (including all routes): 3.75 L (3.96 US qt, 3.30 Imp.qt)Air filter:Air filter element:Oil-coated paper element
Fuel:Recommended fuel:Premium unleaded gasoline (Gasohol [E10]
acceptable)
Fuel tank capacity: 15 L (4.0 US gal, 3.3 Imp.gal)
Fuel reserve amount:
3.9 L (1.03 US gal, 0.86 Imp.gal)Fuel injection:Throttle body:ID mark:2S31 00Spark plu g(s):Manufacturer/model:
NGK/CR9EIA
Manufacturer/model: DENSO/IU27D
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)Clutch:Clutch type:Wet, multiple-discDrivetrain:Primary reduction ratio:
1.509 (86/57)
Final drive: Shaft
Secondary reduction ratio: 3.082 (22/23 x 29/9)
Transmission type:
Constant mesh 5-speed
Gear ratio: 1st:
2.375 (38/16)
U2CEE1E0.book Page 1 Thursday, November 19, 2015 10:32 AM

Specifications
8-3
8
Bulb watta ge × quantity:Headlight:
H4, 60.0 W/55.0 W x 1
Brake/tail light:
LED
Front turn signal light: 10.0 W × 2
Rear turn signal light: 10.0 W × 2
Auxiliary light:
5.0 W × 1
License plate light: 5.0 W × 1
Meter lighting: LED
Neutral indicator light:
LED
High beam indicator light: LED
Oil level warning light: LED
Turn signal indicator light:
LED
Fuel level warning light: LED
Coolant temperature warning light: LED
Engine trouble warning light:
LED
ABS warning light: LED
Immobilizer system indicator light: LED Shift timing indicator light:
LED
Fuse(s):Main fuse:
50.0 A
Headlight fuse: 15.0 A
Signaling system fuse: 7.5 A
Ignition fuse:
20.0 A
Parking lighting fuse: 7.5 A
Radiator fan motor fuse: 20.0 A
Sub radiator fan motor fuse:
7.5 A
Fuel injection system fuse: 15.0 A
ABS control unit fuse: 7.5 A
ABS motor fuse:
30.0 A
ABS solenoid fuse: 15.0 A
Backup fuse: 7.5 A
Electronic throttle valve fuse:
7.5 A
U2CEE1E0.book Page 3 Thursday, November 19, 2015 10:32 AM

10-1
10
IndexAABS ....................................................... 3-20
ABS warning light ................................... 3-6
Air filter element .................................... 6-19
Auxiliary light bulb, replacing ................ 6-37BBattery .................................................. 6-31
Brake and clutch fluids, changing ........ 6-27
Brake and clutch levers, checking and
lubricating ........................................... 6-28
Brake and shift pedals, checking and lubricating ........................................... 6-28
Brake fluid level, checking .................... 6-25
Brake lever ............................................ 3-19
Brake lever free play, checking............. 6-24
Brake light switches.............................. 6-24
Brake pedal........................................... 3-20
Brake/tail light ....................................... 6-37CCables, checking and lubricating ......... 6-27
Care ........................................................ 7-1
Catalytic converters .............................. 3-24
Clutch lever ................................. 3-18, 6-23
Coolant ................................................. 6-16
Coolant temperature warning light ......... 3-5
Cowling and panels, removing and installing................................................ 6-8DDimmer switch ...................................... 3-17EEngine break-in....................................... 5-3
Engine idling speed, checking .............. 6-20
Engine oil and oil filter cartridge ........... 6-11
Engine serial number .............................. 9-1 Engine stop switch ............................... 3-18
Engine trouble warning light ................... 3-5
EXUP system........................................ 3-31
FFinal gear oil ......................................... 6-14
Front and rear brake pads, checking ... 6-25
Front fork, adjusting ............................. 3-26
Front fork, checking ............................. 6-30
Fuel ....................................................... 3-22
Fuel consumption, tips for reducing ...... 5-3
Fuel level warning light ........................... 3-5
Fuel tank breather hose and overflow
hose ................................................... 3-24
Fuel tank cap ........................................ 3-21
Fuses, replacing ................................... 6-34HHandlebar switches .............................. 3-17
Hazard switch....................................... 3-18
Headlight bulb, replacing ..................... 6-35
High beam indicator light ....................... 3-4
Horn switch .......................................... 3-18IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ............... 3-32
Immobilizer system ................................ 3-1
Immobilizer system indicator light .......... 3-6
Indicator lights and warning lights ......... 3-4LLicense plate light bulb, replacing........ 6-38
Luggage strap holders ......................... 3-30MMain switch/steering lock....................... 3-2
Maintenance and lubrication, periodic ... 6-4 Maintenance, emission control
system ..................................................6-3
Matte color, caution ................................7-1
Model label .............................................9-1
Multi-function display .............................3-8
NNeutral indicator light ..............................3-4OOil level warning light ..............................3-4PParking ....................................................5-4
Part locations ..........................................2-1
Pass switch ...........................................3-17SSafety information ...................................1-1
Seats .....................................................3-25
Shifting ....................................................5-2
Shift pedal .............................................3-19
Shift timing indicator light .......................3-6
Shock absorber assembly, adjusting ....3-28
Sidestand ..............................................3-31
Sidestand, checking and lubricating.....6-29
Spark plugs, checking ..........................6-10
Specifications .........................................8-1
Speedometer unit ...................................3-7
Starting the engine ..................................5-1
Start switch ...........................................3-18
Steering, checking ................................6-30
Storage ...................................................7-4
Supporting the motorcycle ...................6-39
Swingarm pivots, lubricating ................6-29TThrottle grip and cable, checking and lubricating ...........................................6-27
U2CEE1E0.book Page 1 Thursday, November 19, 2015 10:32 AM