Page 12 of 96
2-1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Description
EAU63371
Left view
1. Engine oil dipstick (page 6-9)
2. Engine oil filler cap (page 6-9)
3. Fuel tank cap (page 3-8)
4. Fuel cock (page 3-11)
5. Battery (page 6-31)
6. Fuse (page 6-33)
7. Shock absorber assembly spring preload adjusting ring (page 3-13)
8. Shift pedal (page 3-6)
1, 2 4
5, 63
7
8
2RD-28199-E1.book 1 ページ ２０１５年９月３日 木曜日 午後３時４２分
Page 47 of 96
Periodic maintenance and adjustment
6-9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
plug wrench, and then tighten it to
the specified torque.
TIP
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.
3. Install the spark plug cap.
EAU59626
Engine oil and oil filter
element
The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter ele-
ment replaced at the intervals specified
in the periodic maintenance and lubri-
cation chart.
To check the engine oil level1. Start the engine, warm it up for several minutes, and then turn it
off.
2. On a level surface, place the vehi- cle on the centerstand.
3. Wait a few minutes until the oil set- tles. Remove the engine oil filler
cap, wipe the dipstick clean, insert
it back into the oil filler hole (with-
out screwing it in), and then re-
move it again to check the oil level.
WARNING! Never remove the
engine oil filler cap after high-
speed operation, otherwise hot
engine oil could spout out and
cause damage or injury. Always
let the engine oil cool down suf-
ficiently before removing the oil
filler cap.
[EWA17640]
TIP
The engine oil should be between the
minimum and maximum level marks.
Tightening torque:Spark plug:25 Nm (2.5 m·kgf, 18 ft·lbf)
2RD-28199-E1.book 9 ページ ２０１５年９月３日 木曜日 午後３時４２分
Page 48 of 96
Periodic maintenance and adjustment
6-10
1
2
3
4
5
6
7
8
9
10
11
12
13
14 4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Install the oil filler cap.
To change the engine oil (with or
without oil filter element replace-
ment) 1. Start the engine, warm it up for several minutes, and then turn it
off.
2. Place an oil pan under the engine to collect the used oil.
3. Remove the oil filter element cover bleed bolt and its gasket, and the
oil filter element drain bolt to drain
the oil from the oil filter element
chamber. 4. Remove the engine oil drain bolt
and its gasket to drain the oil from
the crankcase.
5. Remove the engine oil filler cap, the engine oil tank drain bolt and
its gasket to drain the oil from the
oil tank.
1. Engine oil filler cap
2. Dipstick
3. Maximum level mark
4. Minimum level mark
3
4
1
2
1. Oil filter element cover bleed bolt
2. Gasket
3. Oil filter element drain bolt
1. Gasket
2. Engine oil drain bolt (crankcase)
1
2
3
21
2RD-28199-E1.book 10 ページ ２０１５年９月３日 木曜日 午後３時４２分
