2016 YAMAHA SR400 check oil

Periodic maintenance and adjustment
6-26
1
2
3
4
5
6
7
8
9
10
11
12
13
14 6. Take the motorcycle off the center-
stand, and then put the sidestand
down.
7. Tighten both drive chain puller locknuts to the specified torque,
and then tighten the axle nut and
brake torque rod nut to their speci-
fied torques.
8. Adjust the brake pedal free play. (See page 6-20.)
WARNING
EWA10661
After adjusting the brake pedal free
play, check the operation of the
brake light.
9. Make sure that the drive chain pull- ers are in the same position, the
drive chain slack is correct, and the
drive chain moves smoothly.
EAU23026
Cleaning and lubricating the
drive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.
NOTICE
ECA10584
The drive chain must be lubricated
after washing the motorcycle, riding
in the rain or riding in wet areas.
1. Clean the drive chain with kero- sene and a small soft brush.
NOTICE: To prevent damaging
the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents.
[ECA11122]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain
lubricant. NOTICE: Do not use
engine oil or any other lubri-
cants for the drive chain, as they
may contain substances that
could damage the O-rings.
[ECA11112]
1. Axle nut
2. Drive chain puller locknut
3. Drive chain slack adjusting bolt
4. Alignment marks
Tightening torques: Drive chain puller locknut:16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle nut: 129 Nm (12.9 m·kgf, 92 ft·lbf)
Brake torque rod nut:
19 Nm (1.9 m·kgf, 14 ft·lbf)
1
2
(a) (b)
3
4
2RD-28199-E1.book 26 ページ ２０１５年９月３日　木曜日　午後３時４２分

Periodic maintenance and adjustment
6-30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
EAU51951
Checking the front fork
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
Check the front fork for damage and ex-
cessive oil leakage.
To check the operation 1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.
[EWA10752]
2. While applying the front brake, push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
NOTICE
ECA10591
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
EAU45512
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.1. Place the vehicle on the center- stand. WARNING! To avoid inju-
ry, securely support the vehicle
so there is no danger of it falling
over.
[EWA10752]
2. Hold the lower ends of the front fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
2RD-28199-E1.book 30 ページ ２０１５年９月３日　木曜日　午後３時４２分

Motorcycle care and storage
7-4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
EAU43204
Storage
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the motor-
cycle.
NOTICE
ECA10811
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months: 1. Follow all the instructions in the “Care” section of this chapter.
2. Fill up the fuel tank and add fuel stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro- tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
WARNING! To prevent dam-
age or injury from sparking,
make sure to ground the
spark plug electrodes while
turning the engine
over.
[EWA10952]
e. Remove the spark plug capfrom the spark plug, and then
install the spark plug and the
spark plug cap.
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the sides-
tand/centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0  C (30 F) or more than 30
 C (90 F)]. For more information
on storing the battery, see page
6-31.
TIP
Make any necessary repairs before
2RD-28199-E1.book 4 ページ ２０１５年９月３日　木曜日　午後３時４２分

10-1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Index
A
Air filter element, replacing ................... 6-13
Auxiliary light bulb, replacing ................ 6-36
B
Battery................................................... 6-31
Brake and clutch levers, checking and lubricating ........................................... 6-28
Brake fluid, changing ............................ 6-24
Brake fluid level, checking .................... 6-23
Brake lever .............................................. 3-7
Brake lever free play, adjusting............. 6-19
Brake light switches .............................. 6-22
Brake pads and shoes, checking .......... 6-22
Brake pedal ............................................. 3-7
Brake pedal, checking and
lubricating ........................................... 6-28
Brake pedal height and free play,
adjusting ............................................. 6-20
C
Cables, checking and lubricating .......... 6-27
Care ........................................................ 7-1
Catalytic converter ................................ 3-11
Centerstand and sidestand, checking and lubricating .................................... 6-29
Clutch lever ............................................. 3-6
Clutch lever free play, adjusting ............ 6-18
D
Decompression lever ............................ 3-12
Dimmer switch ........................................ 3-5
Drive chain, cleaning and lubricating .... 6-26
Drive chain slack ................................... 6-25
E
Engine break-in ....................................... 5-5
Engine idling speed, checking .............. 6-14
Engine oil and oil filter element ............... 6-9
Engine serial number .............................. 9-1
Engine stop switch .................................. 3-5
Engine trouble warning light.................... 3-3
F
Front fork, checking .............................. 6-30
Fuel ......................................................... 3-9
Fuel cock............................................... 3-11
Fuel consumption, tips for reducing ........ 5-5
Fuel level warning light ........................... 3-2
Fuel tank breather/overflow hose.......... 3-10
Fuel tank cap .......................................... 3-8
Fuses, replacing.................................... 6-33
H
Handlebar switches................................. 3-4
Hazard switch ......................................... 3-5 Headlight bulb, replacing ...................... 6-35
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-5
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-15
Indicator lights and warning lights .......... 3-2
K
Kickstarter ............................................ 3-12
M
Main switch/steering lock ....................... 3-1
Maintenance and lubrication, periodic .... 6-4
Maintenance, emission control system... 6-3
Matte color, caution ................................ 7-1
Model label ............................................. 9-2
N
Neutral indicator light .............................. 3-2
P
Panel, removing and installing ............... 6-7
Parking ................................................... 5-6
Part locations .......................................... 2-1
Pass switch ............................................ 3-5
S
Safety information .................................. 1-1
Seat ...................................................... 3-13
Shifting ................................................... 5-3
Shift pedal .............................................. 3-6
Shift pedal, chec
king ............................ 6-21
Shock absorber assemblies, adjusting ............................................. 3-13
Sidestand ............................................. 3-14
Spark plug, checking .............................. 6-8
Specifications ......................................... 8-1
Speedometer unit ................................... 3-3
Starting the engine ................................. 5-2
Starting the engine, trouble .................... 5-3
Steering, checking ................................ 6-30
Storage ................................................... 7-4
Swingarm pivots, lubricating ................. 6-29
T
Tachometer ............................................ 3-4
Tail/brake light bulb, replacing .............. 6-37
Throttle grip and cable, checking and
lubricating ........................................... 6-27
Throttle grip free play, checking ........... 6-14
Tires ..................................................... 6-15
Tool kit .................................................... 6-2
Troubleshooting .................................... 6-42
Troubleshooting chart ........................... 6-43
Turn signal indicator light ....................... 3-2
2RD-28199-E1.book 1 ページ ２０１５年９月３日　木曜日　午後３時４２分