2016 VAUXHALL MERIVA torque

140Driving and operatingPower to the Infotainment system willcontinue to operate for 30 minutes oruntil the key is removed from theignition, regardless of whether anydoor is opened.
Starting the engine
Manual transmission: operate clutch.
Automatic transmission: operate
brake and move the selector lever to
P or N.
Do not operate accelerator pedal.
Diesel engine: turn the key to position 2 for preheating until control
indicator ! extinguishes.
Turn the key briefly to position 3 and
release: an automatic procedure operates the starter with a short delay
as long as the engine is running, see
Automatic Starter Control.
Before restarting or to switch off the
engine, turn the key back to position
0 .
During an Autostop, the engine can
be started by depressing the clutch
pedal.
Starting the vehicle at low
temperatures
The start of the engine without
additional heaters is possible down to
-25 °С for diesel engines and -30 °C
for petrol engines. Required is an
engine oil with the correct viscosity,
the correct fuel, performed services
and a sufficiently charged vehicle
battery. With temperatures below
-30 °C the automatic transmission
needs a warming phase of approx.
five minutes. The selector lever must
be in position P.Automatic Starter Control
This function controls the engine
starting procedure. The driver does
not have to hold the key in position 3.
Once applied, the system will go on starting automatically until the engine
is running. Because of the checking
procedure, the engine starts running
after a short delay.
Possible reasons for a non-starting
engine:
● clutch pedal not operated (manual transmission)
● brake pedal not operated or selector lever not in P or N
(automatic transmission)
● timeout occurred
Turbo engine warm-up
Upon start-up, engine available
torque may be limited for a short time, especially when the engine
temperature is cold. The limitation is
to allow the lubrication system to fully
protect the engine.

Vehicle care209
Attach wheel wrench and with the
jack correctly aligned rotate wheel wrench until wheel is clear of the
ground.
5. Unscrew the wheel bolts. 6. Change the wheel.
7. Screw on the wheel bolts.
8. Lower vehicle.
9. Install the wheel wrench ensuring that it locates securely and tighten
each bolt in a crosswise
sequence. Tightening torque is
110 Nm.
10. Align the valve hole in the wheel cover with the tyre valve before
installing.
Install wheel bolt caps.
11. Stow the replaced wheel 3 209,
the vehicle tools 3 194 and the
adapter for the locking wheel bolts 3 60.
12. Check the tyre pressure of the installed tyre and also the wheel
bolt torque as soon as possible.
Have the defective tyre renewed or repaired.
Jacking position for lifting platform
Rear arm position of the lifting
platform at the underbody.
Front arm position of the lifting
platform at the underbody.
Spare wheel Some vehicles are equipped with a
tyre repair kit instead of a spare
wheel.
If mounting a spare wheel, which is
different from the other wheels, this
wheel might be classified as a
temporary spare wheel and the
corresponding speed limits apply,
even though no label indicates this.
Seek the assistance of a workshop to
check the applicable speed limit.
The spare wheel has a steel rim.

Technical data227Engine dataEngine identifier codeB14XERB14NELB14NELB14NETSales designation1.41.41.4 LPG1.4Engineering codeB14XERB14NELB14NELB14NETPiston displacement [cm3
]1398136413641364Engine power [kW]748888103at rpm60004200-60004800-60004900-6000Torque [Nm]130175/200 2)175200/220 3)at rpm40001750-48001750-48001850-4900Fuel typePetrolPetrolLiquid gas/PetrolPetrolOctane rating RONrecommended95959595possible98989898possible91919191Additional fuel type––Liquid gas (LPG)–2)
With six-speed transmission.
3) With overboost function.

228Technical dataEngine identifier codeB16DTCB16DTLB16DTHB16DTESales designation1.61.61.61.6Engineering codeB16DTLB16DTLB16DTHB16DTEPiston displacement [cm3
]1598159815981598Engine power [kW]708110081at rpm350035003500-40003500Torque [Nm]280300320300at rpm1500-17501750-200020001750-2000Fuel typeDieselDieselDieselDieselEngine identifier codeA13DTCA13DTEA17DTISales designation1.31.31.7Engineering codeA13DTCA13DTEA17DTIPiston displacement [cm 3
]124812481686Engine power [kW]557081at rpm400040003600

Technical data229Engine identifier codeA13DTCA13DTEA17DTISales designation1.31.31.7Engineering codeA13DTCA13DTEA17DTITorque [Nm]180180280at rpm1750-25001750-35002300Fuel typeDieselDieselDieselPerformanceEngineB14XERB14NELB14NEL LPGB14NETMaximum speed [mph]Manual transmission110117117122Automatic transmission–115–120EngineB16DTCB16DTLB16DTHB16DTEMaximum speed [mph]Manual transmission108115122115Automatic transmission––––