2016 TOYOTA iM engine

752. Instrument cluster
2
Instrument cluster
Scion iM_U (12J49U)
nThe meters and display illuminate when
The engine switch is in the “ON” position.
n Outside temperature display
lIn the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 9 mph [15 km/h])
• When the outside temperature has changed suddenly (at the entrance/
exit of a garage, tunnel, etc.)
l If “  ” is displayed continuously, the system may be malfunctioning. Take
your vehicle to your Scion dealer.
NOTICE
n To prevent damage to the engine and its components
lDo not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
l The engine may be overheating if the engine coolant temperature gauge
enters the red zone. In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. (P. 288)

782. Instrument cluster
Scion iM_U (12J49U)
uOperating the meter control switches
The multi-information display is operated using the meter control
switches.: Select menu icons
: Change displayeditem, scroll up/down
the screen and
move the cursor up/
down
Press: Enter/Set
Press and hold: Reset
Return to the previous screen
uDrive information
nDrive information 1/Drive information 2
Displays drive information such as the following:
l Drive information 1
• Current fuel consumption
• Average fuel economy (after reset)
l Drive information 2
• Distance (driving range)
• Average vehicle speed (after reset)
Displayed items (listed below) can be changed on the settings dis-
play. ( P. 80)
Menu icons
1
2
3
ItemContent
Current fuel
consumption Displays instantaneous current fuel consumption
Average fuel economy
(after reset)Displays average fuel consumption since display
reset
*1, 2
Average fuel economy
(after start)Displays average fuel consumption since engine
start
*2
Average fuel economy
(after refuel)Displays average fuel consumption since
refuel
*2, 3

792. Instrument cluster
2
Instrument cluster
Scion iM_U (12J49U)
*1: To reset, display the desired item and press and hold switch. If bothdisplayed items are resettable, a reset selection screen will appear.
*2: Use the displayed fuel consumption as a reference.
*3: When only a small amount of fuel is added to the tank, the display may notbe updated.
When refueling, turn the engine switch off. If the vehicle is refueled without
turning the engine switch off, the display may not be updated.
*4: This distance is computed based on your average fuel consumption. As aresult, the actual distance that can be driven may differ from that dis-
played.
n
Eco Driving Indicator (if equipped)
 P. 8 0
nBlank (No items)
Displays no drive information items.
Average vehicle speed
(after reset)Displays average vehicle speed since display
reset
*1
Average vehicle speed
(after start)Displays average vehicle speed since engine
start
Elapsed time
(after reset)Displays elapsed time since display reset*1
Elapsed time
(after start)Displays elapsed time since engine start
Distance
(driving range)Displays driving range with remaining fuel*3, 4
Distance
(after start)Displays drive distance since vehicle start
BlankNo item
ItemContent

812. Instrument cluster
2
Instrument cluster
Scion iM_U (12J49U)n
Brightness of the meters (day mode and night mode)
lThe brightness of the meters are changed between day mode and night
mode.
• Day mode: When the tail lights are off or when the tail lights are on but
the surrounding area is bright
• Night mode: When the tail lights are on and the surrounding area is dark
l When in night mode, the brightness will be reduced slightly unless the
meters are set to the maximum brightness level.
n Suspension of the settings display
lWhile driving, the multi-information display cannot be changed to setting
mode. Before changing the settings, stop the vehicle in a safe place.
l In the following situations, operation of some of the settings display may be
temporarily suspended.
• When a warning message appears on the multi-information display
• When the vehicle begins to move
n When disconnecting and reco nnecting battery terminals
The drive information data will be reset.
n Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
WARNING
nCaution for use while driving
lWhen operating the multi-information display while driving, pay extra
attention to the safety of the area around the vehicle.
l Do not look continuously at the multi-information display while driving as
you may fail to see pedestrians, objects on the road, etc. ahead of the
vehicle.
n The information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear
number appearing on the display. This lag could cause the driver to down-
shift again, causing rapid and excessive engine braking and possibly an
accident resulting in death or injury.
n Cautions during setting up the display
As the engine needs to be running during setting up the display, ensure that
the vehicle is parked in a place with adequate ventilation. In a closed area
such as a garage, exhaust gases including harmful carbon monoxide (CO)
may collect and enter the vehicle. This may lead to death or a serious
health hazard.

822. Instrument cluster
Scion iM_U (12J49U)
NOTICE
nWhile setting up the display
To prevent battery discharge, ensure that the engine is running while setting
up the display features.

893-2. Opening, closing and locking the doors
3
Operation of each component
Scion iM_U (12J49U)
uDoor lock switchesLocks all the doors
Unlocks all the doors
uInside lock buttonsLocks the door
Unlocks the door
The front doors can be opened
by pulling the inside handle
even if the lock buttons are in
the lock position.
Move the inside lock button to the lock position.
Close the door.
The door cannot be locked if either of the front doors is open and the
key is in the engine switch.
Unlocking and locking the doors from the inside
1
2
1
2
Locking the doors from the outside without a key
1
2

1053-4. Adjusting the steering wheel and mirrors
3
Operation of each component
Scion iM_U (12J49U)
nMirror angle can be adjusted when
The engine switch is in the “ACC” or “ON” position.
n When the mirrors are fogged up
The outside rear view mirrors can be cleared using the mirror defoggers. Turn
on the rear window defogger to turn on the outside rear view mirror defog-
gers. ( P. 169)
WARNING
nImportant points while driving
Observe the following precautions while driving.
Failure to do so may result in loss of control of the vehicle and cause an
accident, resulting in death or serious injury.
lDo not adjust the mirrors while driving.
l Do not drive with the mirrors folded.
l Both the driver and passenger side mirrors must be extended and properly
adjusted before driving.
n When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your
hand caught by the moving mirror.
n When the mirror de foggers are operating
Do not touch the rear view mirror surfaces, as they can become very hot
and burn you.

106
Scion iM_U (12J49U)
3-5. Opening and closing the windows
The power windows can be opened and closed using the switches.
Operating the switch moves the windows as follows:
Closing
One-touch closing (driver’s win-
dow only)
*
Opening
One-touch opening (driver’s
window only)
*
*
: To stop the window partway, oper- ate the switch in the opposite direc-
tion.
Press the switch to lock the pas-
senger window switches.
Use this switch to prevent children
from accidentally opening or clos-
ing a passenger window.
n The power windows can be operated when
The engine switch is in the “ON” position.
n Operating the power windows after turning the engine off
The power windows can be operated for approximately 45 seconds after the
engine switch is turned to the “ACC” or “LOCK” position. They cannot, how-
ever, be operated once either front door is opened.
n Jam protection function (driver’s window only)
If an object becomes caught between the window and the window frame, win-
dow travel is stopped and the window is opened slightly.
n Pinch protection function (driver’s window only)
While the window is opening, if an object is caught between the door and win-
dow, window travel is stopped.
Power windows
Opening and closing procedures
1
2
3
4
Window lock switch