2016 TOYOTA GT86 reset

FT86_EE
14
C
BB
Paddle shift switches ∗ P. 184, 186
Engine (ignition) switch (vehicles
without a smart entry & start system)
P. 178
Cruise control switch ∗ P. 220Horn
SRS driver airbag P. 193
P. 105
Instrument panel light control dial P. 196
Manual headlight leveling dial ∗ P. 210
Trunk opener P. 59
∗: If equipped
Pictorial index
Instrument panel
(Left-hand drive vehicles)
Tire pressure warning system reset
switch
P. 317
86_OM_EE_OM18058E.book 14 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

FT86_EE
21
C
B
Engine (ignition) switch (vehicles
without a smart entry & start system)
P. 178
Cruise control switch ∗ P. 220Horn
SRS driver airbag P. 193
P. 105
Instrument panel light control dial P. 196
Manual headlight leveling dial ∗
P. 210
Trunk opener P. 59
∗: If equipped
Paddle shift switches ∗ P. 184, 186
Tire pressure warning system reset switch
P. 317
86_OM_EE_OM18058E.book 21 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

195 2-2. Instrument cluster
2
When driving
FT86_EE
Odometer, trip meter and multi-information display
Odometer: Displays the total distance the vehicle has been driven.
Trip meter: Displays the distance the vehicle has been driven since the
meter was last reset. Trip meters A and B can be used to record and
display different distances independently.
Multi-information display: Presents the driver with a variety of driving-
related data. (→P. 203)
“DISP” switch
→P. 204
“ODO/TRIP” switch
→P. 196
“km/h MPH” switch (if equipped)
Each time the switch is pressed, the display inside the meter changes
between km/h and MPH.
86_OM_EE_OM18058E.book 195 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

196 2-2. Instrument cluster
FT86_EE
Switch the display
Each time the “ODO/TRIP” switch is pressed, the display changes as
follows.
Odometer
Trip meter A
*
Trip meter B*
*: Pressing and holding the “ODO/TRIP” switch will reset the trip meter that
is currently displayed.
Instrument panel light control
The brightness of the instrument panel lights can be adjusted.
Brighter
Darker
86_OM_EE_OM18058E.book 196 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

204 2-2. Instrument cluster
FT86_EE
Switch the display
Each time the “DISP” switch is pressed, the display changes as fol-
lows.
Outside temperature
→P. 2 6 9
Current fuel consumption
Displays the current rate of fuel consumption.
Average fuel consumption
Displays the average fuel consumption since the function was
reset.
• The function can be reset by pushing the “DISP” switch for longer
than one second when the average fuel consumption is displayed.
• Use the displayed average fuel consumption as a reference.
Setting screen for the REV indicator* (if equipped)
→P. 2 0 5
*: Only displayed when the vehicle is stopped.
86_OM_EE_OM18058E.book 204 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

234 2-5. Driving information
FT86_EE
●If a door is opened and closed when its side window is frozen,
the window safety device will operate and the side window
open/close function linked to door operation may not operate
correctly. If this occurs, perform the following after the ice has
melted.
Open the side window until it is approximately halfway open
with the door closed.
Fully close the window by pulling the switch up to the one-
touch closing position and continue holding the switch for 1
second or more after the window fully closes.
The window position is reset and the safety device operations will
be released.
■When driving the vehicle
Accelerate the vehicle slowly, keep a safe distance between you
and the vehicle ahead, and drive at a reduced speed suitable to
road conditions.
■When parking the vehicle (in the winter time or in the cold
latitudes)
Park the vehicle and move the shift lever to P (automatic trans-
mission) or 1 or R (manual transmission) without setting the
parking brake. The parking brake may freeze up, preventing it
from being released. If necessary, block the wheels to prevent
inadvertent sliding or creeping.
STEP 1
STEP 2
86_OM_EE_OM18058E.book 234 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

268
3-5. Other interior features
FT86_EE
Clock
■The clock is displayed when
Vehicles without a smart entry & start system
The engine switch is in the “ACC” or “ON” position.
Vehicles with a smart entry & start system
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON
mode.
■When disconnecting and reconnecting battery terminals
The clock data will be reset. The clock can be adjusted by pressing the buttons.
Adjusts the hours
Adjusts the minutes
Rounds to the nearest
hour
*
*: e.g. 1:00 to 1:29 → 1:00
1:30 to 1:59 → 2:0000
86_OM_EE_OM18058E.book 268 ページ ２０１５年３月１７日　火曜日　午前１１時３１分

317 4-3. Do-it-yourself maintenance
4
Maintenance and care
FT86_EE■How to initialize the tire pressure warning system
Park the vehicle in a safe place and turn the “ENGINE START
STOP” switch (vehicles with a smart entry & start system) or
the engine switch (vehicles without a smart entry & start sys-
tem) off.
Initialization cannot be performed while the vehicle is moving.
Adjust the tire inflation pressure to the specified cold tire infla-
tion pressure level. (→P. 445)
Make sure to adjust the tire pressure to the specified cold tire infla-
tion pressure level. The tire pressure warning system will operate
based on this pressure level.
Turn the “ENGINE START STOP” switch to IGNITION ON
mode (vehicles with a smart entry & start system) or engine
switch to the “ON” position (vehicles without a smart entry &
start system).
Press and hold the tire pressure
warning reset switch until the tire
pressure warning light blinks
slowly 3 times.
STEP 1
STEP 2
STEP 3
STEP 4
86_OM_EE_OM18058E.book 317 ページ ２０１５年３月１７日　火曜日　午前１１時３１分