2016 SUZUKI GRAND VITARA 4H lock

2-13
BEFORE DRIVING
54P00-01E
Ty p e A
The keyless push start system, controller
model S79M0 and key model R64M0 are
in compliance with the essential require-
ments and other provisions of Directive
1999/5/EC.Keyless entry system transmitter (Type B)
81A184
(1) LOCK button
(2) UNLOCK button
There are two ways to lock or unlock all
doors (including the tailgate) simultane-
ously by operating the transmitter near the
vehicle.Central door locking system
• To lock all doors, push LOCK button (1)
once.
• To unlock only the driver’s door, push
UNLOCK button (2) once.
• To unlock other doors, push UNLOCK
button (2) once again.
NOTE:
You can switch the function that unlocks all
doors from requiring two pushes to requir-
ing one push, and vice versa, via the infor-
mation display setting mode. For details on
how to use the information display, refer to
“Information display” in this section.
Central door locking system with the
dead lock system (if equipped)
If you want to prevent tamper-unlocking of
the door locks, use this method. When the
dead lock system is activated, operating
the lock knobs will not unlock the side
doors.
To activate this system:
To lock all doors, push LOCK button (1)
twice within 3 seconds.
To release this system:
• To unlock only the driver’s door, push
UNLOCK button (2) once.
• To unlock other doors, push UNLOCK
button (2) once again.
(1)
(2)

2-14
BEFORE DRIVING
54P00-01E
NOTE:
You can switch the function that unlocks all
doors from requiring two pushes to requir-
ing one push, and vice versa, via the infor-
mation display setting mode. For details on
how to use the information display, refer to
“Information display” in this section.
The turn signal lights will flash once when
the doors are locked and then the turn sig-
nal lights will flash once again when the
doors are locked with the dead lock sys-
tem.
When the doors are unlocked:
• The turn signal lights will flash twice.
• If the interior light switch is in DOOR
position, the interior light will turn on for
about 15 seconds and then fade out. If
you insert the key into the ignition switch
during this time, the light will start to fade
out immediately.
Check that the doors are locked after you
operate LOCK button (1).
NOTE:
If no door is opened within about 30 sec-
onds after UNLOCK button (2) is operated,
the doors will automatically lock again.NOTE:
• The maximum operating distance of the
keyless entry system transmitter is about
5 m (16 ft.), but this can vary depending
on the surroundings, especially near
other transmitting devices such as radio
towers or CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the transmitter, if the ignition key is
inserted in the ignition switch.
• When any door is open, the door locks
can only be unlocked with the transmit-
ter, and the turn signal light will not flash.
• If you lose one of the transmitters, ask
your SUZUKI dealer as soon as possible
for a replacement. Have your dealer pro-
gram the new transmitter code in your
vehicle’s memory so that the old code is
erased.Battery replacement
If the transmitter becomes unreliable,
replace the battery.
To replace the battery of the transmitter:
68LM248
1) Remove the screw (1), and open the
transmitter cover.
2) Remove the transmitter (2).
WA R N I N G
Do not activate the dead lock system
if there are occupants in the vehicle.
They will be locked in the vehicle and
cannot unlock the doors from inside.
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
• Do not expose it to impacts, mois-
ture or high temperature such as
by leaving it on the dashboard
under direct sunlight.
• Keep the transmitter away from
magnetic objects such as a televi-
sion.
(1)
(2)

2-15
BEFORE DRIVING
54P00-01E
68LM249
(3) Lithium disc type battery:
CR1616 or equivalent
3) Put the edge of a flat-bladed screw-
driver in the slot of the transmitter (2)
and pry it open.
4) Replace the battery (3) so its + terminal
faces “+” mark of the transmitter.
5) Close the transmitter and install it into
the transmitter holder.
6) Close the transmitter cover, install and
tighten the screw (1).
7) Check that the door locks can be oper-
ated with the transmitter.
8) Dispose of the used battery properly
according to applicable rules or regula-
tions. Do not dispose of lithium batter-
ies with ordinary household trash.NOTE:
Used batteries must be disposed of prop-
erly according to applicable rules or regu-
lations and must not be disposed of with
ordinary household trash.
80JM133
(1) Crossed-out wheeled bin symbol
The crossed-out wheeled bin symbol (1)
indicates that a used battery should be col-
lected separately from ordinary household
trash.
By ensuring the used battery is disposed
of or recycled correctly, you will help pre-
vent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropri-
ate battery disposal. The recycling of
materials will help to conserve natural
resources. For more detailed information
about disposing of or recycling of the used
battery, consult your SUZUKI dealer.
(2)
(3)
WA R N I N G
Swallowing a lithium battery may
cause serious internal injury. Do not
allow anyone to swallow a lithium
battery. Keep lithium batteries away
from children and pets. If swallowed,
contact a physician immediately.
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
it, do not expose it to dust or mois-
ture or tamper with internal parts.
(1)

2-16
BEFORE DRIVING
54P00-01E
Ty p e B
The keyless entry system, transmitter
model T68L0 and controller model S54P0
are in compliance with the essential
requirements and other provisions of
Directive 1999/5/EC.Theft deterrent light
(if equipped)
54P000211
This light will blink with the ignition switch
in “LOCK” or “ACC” position, or the ignition
mode “LOCK” (OFF) or “ACC”. The blink-
ing light is intended to deter theft by lead-
ing others to believe that the vehicle is
equipped with a security system.
NOTE:
For the theft deterrent alarm system of
European countries, Mexico and South
Africa models, refer to “For European
countries, Mexico and South Africa” in
“SUPPLEMENT” section.
Windows
Manual window control
(if equipped)
60G010A
Raise or lower the door windows by turning
the handle located on the door panel.
EXAMPLE

2-18
BEFORE DRIVING
54P00-01E
81A009
To open a window, push the top part of the
switch. To close the window, lift up the top
part of the switch.
The driver’s window has AUTO-DOWN
and AUTO-UP features for greater conve-
nience (at toll booths or drive-through
restaurants, for example). This means the
driver can open or close the window with-
out holding the window switch in DOWN or
UP position. Press down or lift up the
driver’s window switch completely and
release it. To stop the window before it
reaches the FULL-DOWN or FULL-UP
position, pull up or push down the switch
briefly.Lock switch (type A)54P000253
Lock switch (type B)
54P000214
The driver’s door also has a lock switch for
the passenger’s window(s). When you
push in the lock switch, the passenger’s
window(s) cannot be raised or lowered byoperating any of the switches (2), (3), (4)
or (5). To restore normal operation, release
the lock switch by pushing it again.
NOTE:
If you drive with one of the rear windows
open, you may hear a loud sound caused
by air vibration. To reduce the sound, open
the driver’s or front passenger’s window, or
narrow the rear window opening.
CLOSE
OPENEXAMPLE
EXAMPLE
WA R N I N G
• You should always lock the pas-
senger’s window operation when
there are children in the vehicle.
Children can be seriously injured if
they get part of their body caught
by the window during operation.
• To avoid injuring an occupant by
window entrapment, check that no
part of the occupant’s body such as
hands or head is in the path of the
electric windows when closing
them.
• Always remove the ignition key or
take the keyless push start system
remote controller with you when
leaving the vehicle even only for a
short time. Also do not leave chil-
dren alone in a parked vehicle.
Unattended children could use the
electric window switches and get
trapped by the window.

2-23
BEFORE DRIVING
54P00-01E
Head restraints
80J001
Head restraints are designed to help
reduce the risk of neck injuries in the case
of an accident. Adjust the head restraint to
the position which places the center of the
head restraint closest to the top of your
ears. If this is not possible for very tall pas-
sengers, adjust the head restraint as high
as possible.NOTE:
It may be necessary to recline the seat-
back to provide enough overhead clear-
ance to remove the head restraint.
Front
61MM0A032
To raise the front head restraint, pull
upward the restraint until it clicks. To lower
the restraint, push down the restraint while
holding in the lock lever. If a head restraint
must be removed (for cleaning, replace-
ment, etc.), push in the lock lever and pull
the head restraint all the way out.
Front seat heater (if equipped)
54P000217
(1) Left seat heater switch
(2) Right seat heater switch
(3) “LO” side
(4) “HI” side
When the ignition switch is in “ON” position
or the ignition mode is “ON”, push one or
both of the seat heater switch(es) to warm
the corresponding seat(s).
• When a seat heater switch is pushed,
the heater inside the corresponding seat
operates.
WA R N I N G
• Never drive the vehicle with the
head restraints removed.
• Do not attempt to adjust the head
restraint while driving.
EXAMPLE
(3) (4)(1)(2)

2-25
BEFORE DRIVING
54P00-01E
54P000218
(1)
EXAMPLE
Unlock Lock
Red
Seatback angle adjustment lever (1)
(if equipped)
Pull the lever up and move the seatback.
After adjustment, move the seatback for-
ward and backward to check that it is
securely latched.
CAUTION
After securing the rear seatback,
check that it is locked securely. If it is
not, red button will appear beside the
lever.

2-26
BEFORE DRIVING
54P00-01E
Head restraints
Head restraints are designed to help
reduce the risk of neck injuries in the case
of an accident.
NOTE:
It may be necessary to fold forward the
seatback to provide enough overhead
clearance to remove the head restraint.
Adjust the head restraint to the position
which places the center of the head
restraint closest to the top of your ears. If
this is not possible for very tall passengers,
adjust the head restraint as high as possi-
ble.Rear
61MM0A033
To raise the rear head restraint, pull
upward the restraint until it clicks. To lower
the restraint, push down the restraint while
holding in the lock lever. If a head restraint
must be removed (for cleaning, replace-
ment, etc.), push in the lock lever and pull
the head restraint all the way out.
When installing a child restraint system,
remove the head restraint.
Folding rear seats
The rear seats of your vehicle can be
folded forward to provide additional cargo
space.
To fold the rear seats forward:
1) Lower the head restraint fully.
2) Hook the webbing of rear seat belts on
the belt guide. For details on rear out-
side seat belt guide, refer to “Rear out-
side seat belt guide” in this section.
3) Stow the rear center lap-shoulder belt.
Refer to “Lap-shoulder belt with detach-
able connector” in this section.
54P000219
4) Pull the release lever on the top of each
split seat, and fold the seatbacks for-
ward.
WA R N I N G
• Never drive the vehicle with the
head restraints removed.
• Do not attempt to adjust the head
restraint while driving.
EXAMPLE
EXAMPLE