2016 SUZUKI CELERIO oil

7-7
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
(For Diesel Engine Model)
76MH024
(1) Preferred
Be sure that the engine oil you use comes under the quality classification of ACEAA5/B5-10. Select the appropriate oil vis- cosity according to the above chart.
Oil Level Check
76MH030
(1) Engine oil dipstick (Petrol engine) (2) Engine oil dipstick (Diesel engine)
It is important to keep the engine oil at the correct level for proper lubrication of yourvehicle’s engine. Check the oil level with the vehicle on a level surface. The oil level indication may be inaccurate if the vehicleis on a slope. The oil level should be checked either before starting the engine or at least 5 minutes after stopping theengine.
The handle of the engine oil dipstick is col- ored yellow for easy identification.
52D084
Pull out the oil dipstick, wipe oil off with aclean cloth, insert the dipstick all the way into the engine, then remove it again. Theoil on the stick should be between the upper and lower limits shown on the stick. If the oil level indication is near the lowerlimit, add enough oil to raise the level to the upper limit.
(1)
-30
-22 -4 14 32 50 68 86 104
-20 -10 10 20 30 40 0
5W-30
(1)
(2)
EXAMPLE
NOTICE
Failure to check the oil level regularly could lead to serious engine trouble due to insufficient oil.
EXAMPLEUpper Lower
145

7-8
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
Refilling
81A147
Remove the oil filler cap and pour oil slowly through the filler hole to bring the oil level to the upper limit on the dipstick. Be careful not to overfill. Too much oil is almost asbad as too little oil. After refilling, start the engine and allow it to idle for about a min- ute. Stop the engine, wait about 5 minutesand check the oil level again.
Changing Engine Oil and FilterDrain the engine oil while the engine is stillwarm.
76MH037
(1) Engine oil filler cap (Petrol engine)(2) Engine oil filler cap (Diesel engine)
1) Remove the oil filler cap. 2) Place a drain pan under the drain plug.3) Using a wrench, remove the drain plug and drain out the engine oil.
68KH068
Tightening torque for drain plug (1):Petrol engine: 35 Nm (3.6 kg -m, 25.8 lb-ft) Diesel engine: 35 Nm (3.6 kg -m, 25.8 lb-ft)
NOTICE
(For Diesel Engine Model) Do not top up the oil over the MAX limit. Too much oil causes serious engine trouble.
Close Open
EXAMPLE
CAUTION
The engine oil temperature may behigh enough to burn your fingers when the drain plug is loosened. Waituntil the drain plug is cool enough to touch with your bare hands.
(2)
(1)
Open Close
EXAMPLE
WA R N I N G
New and used oil can be hazardous.Children and pets may be harmed by swallowing new or used oil. Keepnew and used oil and used oil filters away from children and pets. Repeated, prolonged contact withused engine oil may cause skin can- cer. Brief contact with used oil may irri-tate skin. (Continued)
(1)
EXAMPLE
146

7-9
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
4) Reinstall the drain plug and gasket. Tighten the plug with a wrench to thespecified torque.
Replace the Oil Filter
1) Using an oil filter wrench, turn the oil fil-ter counterclockwise and remove it. 2) Using a clean rag, wipe off the mount- ing surface on the engine where thenew filter will be seated. 3) Smear a little engine oil around the rub- ber gasket of the new oil filter.4) Screw on the new filter by hand until the filter gasket contacts the mounting sur- face.
(For Petrol Engine Model)
54G092
(1) Loosen (2) Tighten
Tightening (viewed from filter top)
82JN146
(1) Oil filter (2) 1 turn
(For Diesel Engine Model)
76MH031
(1) Loosen (2) Tighten
Tightening (viewed from filter top)
54G093
(1) Oil filter (2) 3/4 turn
WA R N I N G
(Continued) To minimize your exposure to usedoil, wear a long-sleeve shirt and moisture-proof gloves (such as dish- washing gloves) when changing oil. Ifoil contacts your skin, wash thor- oughly with soap and water. Launder any clothing or rags if wetwith oil. Recycle or properly dispose of used oil and filters.
(1)
(2)
(1) (2)
147

7-10
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
5) Tighten the filter specified turn from the point of contact with the mounting sur- face (or to the spec ified torque) using an oil filter wrench.
Tightening torque for oil filter Petrol engine: 1 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)Diesel engine: 3/4 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)
Refill with Oil and Check for Leaks1) Pour oil through the filler hole andinstall the filler cap. For the approximate capacity of the oil, refer to the “CAPACITIES” item in the “SPECIFICATIONS” section.2) Start the engine and look carefully for leaks at the oil filter and drain plug. Run the engine at various speeds for at least5 minutes.
3) Stop the engine and wait about 5 min- utes. Check the oil level again and add oil if necessary. Check for leaks again.
Engine Coolant
Selection of CoolantTo maintain optimum performance anddurability of your engine, use MARUTIGenuine Coolant or equivalent. This type of coolant is best for your cooling system as it: Helps maintain proper engine tempera- ture. Gives proper protection against freezingand boiling. Gives proper protection against corro- sion and rust.Failure to use the proper coolant can dam- age your cooling system. Your authorized
MARUTI SUZUKI dealer can help you select the proper coolant.
Coolant Level CheckCheck the coolant level at the reservoirtank, not at the radiator. With the engine cool, the coolant level should be betweenthe “FULL” and “LOW” marks.
NOTICE
To tighten the oil filter properly, it isImportant to accurately identify theposition at which the filter gasket first contacts the mounting surface.
NOTICE
To prevent oil leakage, make sure that the oil filter is tight, but do notover-tighten it.
NOTICE
• When replacing the oil filter, it is rec-ommended that you use a Marutigenuine replacement filter. If you use an after market filter, make sure it is of equivalent quality and followthe manufacturer’s instructions. • Oil leaks from around the oil filter or drain plug indicate incorrectinstallation or gasket damage. If you find any leaks or are not sure that the filter has been properlytightened, have the vehicle inspected by your MARUTI SUZUKI dealer.
NOTICE
To avoid damaging your cooling sys- tem: • Always use a high quality ethyleneglycol base non-silicate type cool- ant diluted with distilled water at the correct mixture concentration.• Make sure that the proper mix is 50/ 50 coolant to distilled water (Die- sel) and 30/70 (Petrol). Concentra-tions greater than this may cause overheating conditions. • Neither use 100% coolant nor 100%Plain water. • Do not add extra inhibitors or addi- tives. They may not be compatiblewith your cooling system. • Do not mix different types of base coolants. Doing so may result inaccelerated seal wear and/or the possibility of severe overheating and extensive engine damage.
148

7-12
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
Coolant ReplacementSince special procedures are required, we recommend you take your vehicle to your MARUTI SUZUKI dealer for coolant replacement.
Air Cleaner
If the air cleaner is clogged with dust, therewill be greater intake resistance, resulting in decreased power output and increased fuel consumption.
(For Petrol Engine Model)
76MH0A109
Unclamp the upper clamps, and remove the element from the air cleaner case. If itappears to be dirty, replace it with a new one.
(For Diesel Engine Model)
76MH033
Unclamp the side clamps, and remove the element from the air cleaner case. If it appears to be dirty, replace it with a newone.
Spark Plugs
76MH0A109
68KH072
For nickel spark plugs (traditional type): You should inspect spark plugs periodically for carbon deposits. When carbon accu-mulates on a spark plug, a strong spark may not be produced. Remove carbon deposits with a wire or pin and adjust thespark plug gap.
To access the spark plugs: 1) Unclamp and remove the bolt, then remove the air cleaner case. 2) If necessary, disconnect the coupler (1)while pushing the release lever. 3) Remove the bolts. 4) Pull the ignition coils out.
NOTE: When installation, make sure the wires,couplers, sealing rubber of top cover and washers, are correctly returned in place.
EXAMPLE
EXAMPLE
EXAMPLE
(1)
EXAMPLE
150

7-13
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
78K179 60G160S 60B307
Spark plug gap “a” NGK KR6A-10: 0.95 – 1.05 mm (0.037 – 0.041 in.)NOTICE
• When pulling the ignition coils out,do not pull on the cable. Pulling onthe cable can damage it. • When servicing the iridium/plati- num spark plugs (slender centerelectrode type plugs), do not touch the center electrode, as it is easy to damage.
Correct Wrong
EXAMPLE
NOTICE
• When installing the spark plugs,screw them in with your fingers to avoid stripping the threads. Tighten with a torque wrench to 17.5 Nm (1.8 kg-m, 12.9 lb-ft). Donot allow contaminants to enter the engine through the spark plug holes when the plugs are removed.• Never use spark plugs with the wrong thread size.
Loosen
Tighten
NOTICE
When replacing spark plugs, you should use the brand and type speci-fied for your vehicle. For the speci- fied plugs, refer to the “SPECIFICATIONS” section at theend of this book. If you wish to use a brand of spark plug other than the specified plugs, consult your MAR-UTI SUZUKI dealer.
151

7-14
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
Gear Oil
Manual Transaxle Oil/
Auto Gear Shift OilWhen adding gear oil, use gear oil with the appropriate viscosity and grade as shown in the chart below.
We highly recommend you use: “MARUTI SUZUKI GEAR OIL 75W-80” formanual transaxle gear oil or Auto Gear Shift oil.
Manual transaxle oil (API GL-4)
68LM728
Gear Oil Level Check
68KH073
(1) Oil filler and level plug
To check the gear oil level, use the follow- ing procedure:
1) Park the vehicle on a level surface with the parking brake applied. Then, stop the engine.2) Remove the oil filler plug (1). 3) Check the inside of the hole with your finger. If the oil level comes up to thebottom of the plug hole, the oil level is correct. If so, reinstall the plug. 4) If the oil level is low, add gear oilthrough the oil filler plug hole (1) until the oil level reaches the bottom of the filler hole, then reinstall the plug.
Tightening torque (1): 21 Nm (2.1 kg -m, 15.5 lb-ft)
Gear Oil ChangeSince special procedures, materials and tools are required, it is recommended that you trust this job to your authorized MAR-UTI SUZUKI dealer.
Clutch Pedal
Cable control clutch (if equipped)
54G274
Clutch pedal play “d”: 10 - 15 mm (0.4 - 0.6 in.)
C Fo o-30 -22 -20 -4 -10 14 32 50 68 86 104 010203040
75W-80
(1)
EXAMPLE
CAUTION
After driving the vehicle, the transaxle oil temperature may behigh enough to burn your skin. Wait until the oil filler plug is cool enough to touch with your bare hands beforeinspecting transaxle oil.
NOTICE
When tightening the plug, apply thefollowing sealing compound orequivalent to the plug threads to pre- vent oil leakage.
Manual transaxle sealant: MARUTI SUZUKI Bond No. “1216E” or “1217G”
EXAMPLE
152

7-23
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
The fuse box is located under the driver’s side of the dashboard. Remove the fuse box cover by pushing inat both ends and pulling off the cover.
81A283
Bulb ReplacementMAIN FUSE/PRIMARY FUSE
(1) 10A Stop light
(2) 30A Blower motor
(3) 10A ST SIG
(4) 15A Accessory
(5) 10A Rear fog light
(6) 10A Tail light
(7) 10A Back-up light
(8) 10A ABS
(9) 10A Meter
(10) 15A Ignition coil
(11) 20A Wiper/Washer
(12) 10A IG2 SIG
(13) 10A IG1 SIG
(14) 10A Air bag
(15) 20A Power window timer
(16) 20A Door lock
(17) 15A Horn/Hazard
(18) 20A Rear defogger
(19) 15A Dome
(20) 30A Power window
(21) 7.5A ACC 2
(22) 15A Radio 2
(23) – Blank
(24) – Blank
WA R N I N G
Always be sure to replace a blown fuse with a fuse of the correct amper- age. Never use a substitute such as aluminum foil or wire to replace ablown fuse. If you replace a fuse and the new one blows in a short period of time, you may have a major electri-cal problem. Have your vehicle inspected immediately by your MAR- UTI SUZUKI dealer.
BLOWN OK
CAUTION
• Light bulbs can be hot enough toburn your finger right after being turned off. This is true especially for halogen headlight bulbs.Replace the bulbs after they become cool enough. • The headlight bulbs are filled withpressurized halogen gas. They can burst and injure you if they are hit or dropped. Handle them carefully.
NOTICE
The oils from your skin may cause ahalogen bulb to overheat and burst when the lights are on. Grasp a new bulb with a clean cloth.
NOTICE
Frequent replacement of a bulb indi-cates the need for an inspection of the electrical system. This should be carried out by your MARUTI SUZUKIdealer.
161