2016 RENAULT MEGANE HATCHBACK remove seats

headrest................................................ (up to the end of the DU)
front seatsadjustment ...................................... (up to the end of the DU)
adjusting your driving position .............. (up to the end of the DU)
1.15
ENG_UD18801_8
Appuis-tête avant (B74 - K74 - X81 - J81 - X91 - B91 - K91 - D91 - X\
95 - B95 - D95 - J95 - R95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Headrests - Seats
fRONT HEAdREsTs
To raise the headrest
Pull the headrest upwards to the de-
sired height.
To lower the headrest
Press button 2 and guide the headrest
down to the desired height.
To adjust the angle of the
headrest
Depending on the vehicle, tilt section A
t owards or away from you to the re-
quired position.
To remove the headrest
Raise the headrest to its highest po-
sition (tilt the seatback backwards if
necessary). Press button
1

and lift the
headrest to release it.
To refit the headrest
Pull out the headrest rods 3 as far as
possible by pulling from the top. Take
care to ensure they are clean and cor-
rectly aligned and, if there are any prob-
lems, check that the notches are facing
forwards.
Insert the headrest rods into the holes
(tilt the seatback backwards if neces-
sary).
Lower the headrest until it locks, press
button
1 and lower the headrest as far
as possible.
Check that each headrest rod
3

is se-
curely locked in the seatback by trying
to pull them up or push them down.
The headrest is an impor-
tant safety component:
ensure that it is in place and
in the correct position. The
distance between your head and the
headrest and the distance between
the head and section
A

should be
as small as possible.
2
3
A1
The three upper positions can
be manipulated without pressing
button
2. However, it is preferable to
press this button to lower the head-
rest.

access to the rear seats ........................................ (current page)
1.21
ENG_UD21771_3
Sièges avant: accès aux places arrière (X95 - B95 - D95 - Rena\
ult)
ENG_NU_837-8_BDK95_Renault_1
Electrically controlled seatsLift handle 1 and tilt the seatback com-
pletely: the seat moves forward.
T
o return the seat to its original position,
bring the seatback back up. The seat
returns to its original position.
AccEss TO REAR sEATs, THREE-dOOR vERsION
manually controlled seats
Lift handle 1 and slide the seat forward.
T o return the seat to its original position,
bring the seatback back into position.
Check that no object or
person prevents the front
seat from locking. If so,
r e m o v e a n y o b s t a c l e s
behind the front seats. Adjust the
seat to allow sufficient room in the
rear. The rear occupants/objects
should then return to the vehicle.
Repeat the above until the seat is
locked correctly.
Risk of seat moving on its runners
during vehicle acceleration or brak-
ing.
Do not move handle 1 and handle 2
or switch 4 at the same time.
1
2
Locking the seats
When a person, an object or a child
seat prevents the front seats from lock-
ing, perform the following operations:
–

a
sk all of the passengers to leave
the vehicle and remove any bulky
objects from the rear seats;
–

lock
the seat(s) in the initial position
again;
–

move
the seat(s) forwards in order to
create sufficient space;
–

ask
the passengers to get back into
the vehicle, and refit the child seat or
objects on the rear seats.
special note : if the seatback is
tilted over the rear bench seat, only
use control

3
to return it to the driv-
ing position.
Never use handle

1
as it is not de-
signed for this purpose: there is a
risk of damage to the mechanism.
1
4
3

seat belts .............................................. (up to the end of the DU)
driving position settings ........................................... (up to the end of the DU)
adjusting your driving position ............................... (current page)
front seats adjustment ...................................... (up to the end of the DU)
1.22
ENG_UD21482_6
Ceintures de sécurité (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Jaune NoirNoir texte
Always wear your seat belt when trav-
elling in your vehicle. You must also
comply with the legislation of the par-
ticular country you are in.
Seat belts
I n c o r r e c t l y a d j u s t e d o r
twisted seat belts may
cause injuries in the event
of an accident.
Use one seat belt per person,
whether child or adult.
Even pregnant women should wear
a seat belt. In this case, ensure that
the lap belt is not exerting too much
pressure on the abdomen, but do
not allow any slack.
Before starting, first adjust your driv-
ing position, then ask all occupants
to adjust their seat belts to ensure
optimum protection.
Adjusting your driving
position
– sit well back in your seat (having
first removed your coat or jacket).
This is essential to ensure your back
is positioned correctly;
–

a
djust the distance between the
seat and the pedals. Your seat
should be as far back as possible
while still allowing you to depress
the clutch pedal fully. The seatback
should be adjusted so that your arms
are slightly bent when you hold the
steering wheel;
–

a
djust the position of your head-
rest. For maximum safety, your head
must be as close as possible to the
headrest;
–

adjust
the height of the seat. This
adjustment allows you to select the
seat position which offers you the
best possible view;
–

adjust
the position of the steering
wheel.
Adjusting the seat belts
Sit with your back firmly against the
seatback.
Shoulder strap
1 should be as close as
possible to the base of the neck but not
on it.
Lap belt
2 should be worn flat over the
thighs and against the pelvis.
The belt should be worn so that it is
as close as possible to your body, i.e.:
avoid wearing heavy clothing or keep-
ing bulky objects under the belts, etc.
sEAT BELTs (1/3)
1
2
Make sure that the rear bench seat
is locked in position correctly so that
the rear seat belts will operate effi-
ciently. Refer to the information on
the “Rear bench seat” in Section 3.

1.36
ENG_UD16659_3
Sécurité enfants : choix de la fixation du siège enfant (D91 -\
X95 - B95 - D95 - K95 - L38 - X38 - X32 - B32 - Renault)
ENG_NU_837-8_BDK95_Renault_1
cHILd sAfETY: choosing a child seat mounting (2/2)
The ISOFIX anchorage
points have been exclu-
sively designed for child
seats with the ISOFIX
system. Never fit a different type of
child seat, seat belt or other objects
to these anchorage points.
Check that nothing is obstructing
the anchorage points.
If your vehicle has been involved in
a road accident, have the ISOFIX
anchorage points checked and re-
place your child seat.
The third ring is used to attach the
upper strap on some child seats.
Pass the belt between the seatback
and the rear parcel shelf (to remove
the parcel shelf: refer to Section 3
“Parcel shelf”). Fix the hook on one of
the rings

3
located in the luggage com-
partment (visible for three- and five-
door versions; under the carpet and
indicated with a marking on the Sport
tourer version).
Pull the belt so that the back of the child
seat comes into contact with the vehicle
seatback.
The two rings 1

are located between
the seatback and the seat base of the
seat and are identified by a marking.
To ensure your child seat can be easily
fitted and locked on the rings
1 ,

use
access guides

2

on the child seat.
3
1
2

child restraint/seat ................................ (up to the end of the DU)
child restraint/seat ................................ (up to the end of the DU)
child restraint/seat ................................ (up to the end of the DU)
child safety............................................ (up to the end of the DU)
child seats............................................. (up to the end of the DU)
transporting children ............................. (up to the end of the DU)
1.37
ENG_UD23611_7
Sécurité enfants : installation du siège enfant (X95 - B95 - D\
95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Some seats are not suitable for fitting
child seats. The diagram on the follow-
ing page shows you how to attach a
child seat.
The types of child seats indicated may
not be available. Before using a differ-
ent child seat, check with the manufac-
turer that it can be fitted.
Fitting a child seat
cHILd sAfETY: f itting a child seat (1/6)
In the rear side seat
A carrycot can be installed across the
vehicle and will take up at least two
seats. Position the child with his or her
feet nearest the door.
Push the vehicle seat fully forwards
to install a rear-facing child seat, then
push it back as far as possible with-
out allowing it to make contact with the
child seat.
For the safety of the child in the for-
ward-facing seat, do not move the seat
in front back past the middle of the
runner, do not tilt the seatback too far
(maximum of 25°) and raise the seat as
much as possible.
Check that the forward-facing child seat
is resting against the back of the vehi-
cle seat and that the headrest of the ve-
hicle is not obstructing its use.
In the front seat
The laws concerning children travel-
ling in the front passenger seat differ in
every country. Consult the legislation in
force and follow the indications on the
diagram on the following page.
Before fitting a child seat in this seat (if
authorised):
–

lower

the seat belt as far as possible;
–

move

the seat as far back as possi-
ble;
–

g

ently tilt the seatback away from
vertical (approximately 25°);
–

on

equipped vehicles, raise the seat
base as far as possible.
Do not change these settings after the
child seat is installed.
R IsK Of dE AT H O R sE
RIOUs INJURY: before
fitting a rear-facing child
seat in this position, check
that the air bag has been deacti-
vated (refer to the information on
“Child safety: deactivating/activat-
ing the front passenger air bag” in
Section 1).
Fit the child seat in a rear
seat wherever possible.
Check that when installing
the child seat in the vehicle
it is not at risk of coming loose from
its base.
If you have to remove the headrest,
check that it is correctly stored so
that it does not come loose under
harsh braking or impact.
Always attach the child seat to the
vehicle even if it is not in use so that
it does not come loose under harsh
braking or impact.
Ensure that the child seat
or the child’s feet do not
prevent the front seat from
locking correctly. Refer to
the information on the “Front seat”
in Section 1.

1.40
ENG_UD23611_7
Sécurité enfants : installation du siège enfant (X95 - B95 - D\
95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Jaune NoirNoir texte
cHILd sAfETY: f itting a child seat (4/6)
X = Seat not suitable for fitting child seats.
U =
Seat which allows a child seat with “Universal” approval to be ins\
talled using a seat belt; check that it can be fitted.
IU

f /IL =

On
equipped vehicles, seat which allows an approved “Universal”/”semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(2)

Only
a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,
tilting the seatback slightly (approximately 25°).
(3)
A

carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(4)

Move
the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child sea\
t.
(5)

Forward-facing
child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the front seat more than halfway back on its runners and do not recline the
seatback more than 25°.

1.42
ENG_UD23611_7
Sécurité enfants : installation du siège enfant (X95 - B95 - D\
95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
cHILd sAfETY: f itting a child seat (6/6)
Type of child seat
(sport tourer version) Weight of
the childs eat size
I
s O f IXf ront passenger
seat (1) (5) Rear side seats Rear centre
seat
c

arrycot fitted across the vehicle
Group 0 < 10 kg
F - GXU - IL (2) X
s

hell seat/rear-facing seat
Group 0, or 0+ and 1 <
1

3
k
g and 9
t
o
18 kg E, D, C
UU - IL (3) X
f

orward-facing seat
Group 1 9 to 18 kg
A, B, B1XU - IUF - IL (4) X
Booster seat
Group 2 and 3 15 to 25 kg and 22
to 36 kg
X
U (4)X
X =

Seat not suitable for fitting child seats.
U

=

Seat which allows a child seat with “Universal” approval to be ins\
talled using a seat belt; check that it can be fitted.
IU

f
/IL =

On
equipped vehicles, seat which allows an approved “Universal”/”semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(1)

Only

a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,
tilting the seatback slightly (approximately 25°).
(2)
A

carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(3)

Move
the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child sea\
t.
(4)

Forward-facing
child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the front seat more than halfway back on its runners and do not recline the
seatback more than 25°.
(5) RIsK Of d EATH OR s ERIOU s INJURY: before installing a rear-facing child seat on the front passenger seat,
check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front
passenger air bag” at the end of the section).
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-
tions in force are respected.

3.24
ENG_UD21546_6
Banquette arrière (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_3
when refitting the seat-
back , make sure it is cor-
rectly locked in place.
If seat covers are fitted ,
make sure these do not prevent the
seatback latch from locking in.
Make sure that the seat belts are
positioned correctly.
Reposition the headrests.
The seat and the seatback may be
folded away to allow bulky objects to be
carried.
To fold away the seat base
Tilt seat base
B against the front seats.
To fold down the seatback
After folding the seat base down,
remove the rear headrests (refer to the
section on “rear headrests”) then press
button
1 and lower the seatback(s)
C
.
In all situations, remove the rear
headrests (refer to the informa-
tion on the “Rear headrests” in
Section 1).
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
1
cB
REAR BENch SEAT functions (3/3)
When moving the rear
bench seat, ensure that
nothing obstructs the an-
chorage points (part of the
body, a pet, gravel, cloth, toys, etc.).