2016 RENAULT MEGANE HATCHBACK lights

rear view mirrors ................................... (up to the end of the DU)
1.69
ENG_UD21504_2
Rétroviseurs (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Door mirrors
folding door mirrors
T he door mirrors automatically fold in
when the vehicle is locked (switch
2 in
position
B )

. In this case, they will fold
out when the ignition is next switched
on.
In any case, you can make the door
mirrors fold in (switch
2 in position C) or
fold out (switch
2 in position
A
).
Automatic mode is then deactivated. To
reactivate it, position switch

2
to B.
REAR vIEW mIRRORs
door mirrors
Adjustment
Select the door mirror using switch 3,
then
use button 1 to adjust it to the de-
sired position.
Heated door mirrors
Mirror de-icing is carried out at the
same time as rear screen de-icing.
The driver ’s door mirror
may have two clearly de-
fined zones. Zone
E shows
what can normally be seen
in an ordinary rear view mirror.
Zone

D increases rear side visibility.
The objects in zone
D look much
further away than they really are.
Interior rear view mirror
Its position can be adjusted.
Rear view mirror with lever
4
When driving at night, to avoid being
dazzled by the headlights of the vehicle
behind, depress the little lever located
behind rear view mirror

4
.
Rear view mirror without lever
4
The rear view mirror darkens automati-
cally at night if you are being followed
by a vehicle with its lights on.
1
2
A
c
B
4
dE
3

warning buzzer ..................................... (up to the end of the DU)
headlight flashers ................................. (up to the end of the DU)
indicators .............................................. (up to the end of the DU)
lights: hazard warning ............................... (up to the end of the DU)
lights: direction indicators .......................... (up to the end of the DU)
indicators: direction indicators .......................... (up to the end of the DU)
hazard warning lights signal ................. (up to the end of the DU)
hazard warning lights signal ................. (up to the end of the DU)
horn ...................................................... (up to the end of the DU)
horn: flash ................................................................. (current page)
horn: sounding the horn ............................................ (current page)
horn ....................................................................... (current page)
audible and visual signals..................... (up to the end of the DU)
1.70
ENG_UD6289_1
Avertisseurs sonore et lumineux (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Audible and visual signals
AUdIBLE ANd vIsUAL sIgNALs
Horn
Press on the sides of the steering wheel
boss
A.
Headlight flasher
Pull stalk 1 towards you to flash the
headlights.
éHazard warning lights
Press switch 2. This switch ac-
t
ivates all four direction indicators and
the side indicator lights simultaneously.
It must only be used in an emergency to
warn drivers of other vehicles that you
have had to stop in an area where stop-
ping is prohibited or unexpected or that
you are obliged to drive under special
conditions.
Depending on the vehicle, the hazard
warning lights may come on automati-
cally under heavy deceleration. You can
switch them off by pressing switch
2.
direction indicators
Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it.
When driving on the motorway, the
steering wheel is not often turned
enough to return the stalk automatically
to
0 .

There is an intermediate position
in which the stalk may be held when
changing lanes.
When the stalk is released, it automati-
cally returns to
0.
A
2
1
0

lighting:exterior ............................................ (up to the end of the DU)
instrument panel .................................................... (current page)
lights: side lights ......................................................... (current page)
lights: dipped beam headlights ................................... (current page)
hazard warning lights signal .................................. (current page)
signals and lights .................................. (up to the end of the DU)
lighting: instrument panel .............................................. (current page)
daytime running lights............................................ (current page)
1.71
ENG_UD24014_3
Éclairages et signalisations extérieurs (X95 - B95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
daytime running lights
function
Depending on the vehicle, the daytime
running lights come on automatically
when the engine is started. To activate
or deactivate this function, refer to the
information on the “Vehicle settings
customisation menu” in Section 1.
ámain beam headlightsWith the dipped beam head-
lights lit, pull stalk 1
towards you. This
indicator light on the instrument panel
comes on.
To return to the dipped headlight posi-
tion, pull stalk
1 towards you again.
Exterior lighting and signals
Before driving at night,
check that the electrical
equipment is operating cor-
rectly and adjust the head-
light beams (if your vehicle is not
carrying its normal load). As a gen-
eral precaution, check that the lights
are not obscured (by dirt, mud,
snow or objects being transported).
EXTERIOR LIgHTINg AN d s I g NAL s (1/3)
1
31
uside lights
Turn the ring 2 until the symbol
i
s opposite mark 3 .
This indicator light
on the instrument panel comes on.
kdipped beam
headlights
manual operation
T urn the ring 2 until the symbol is oppo-
site mark
3 .

This indicator light on the
instrument panel comes on. Automatic operation
(depending on vehicle)
Turn ring
2 until the AUTO symbol is op-
posite mark 3: with the engine running,
the dipped beam headlights switch on
or off automatically depending on the
brightness of the light outside, without
any action on stalk 1.
2
If driving on the right in a left-hand
drive vehicle (or vice versa), drivers
are recommended to have the lights
adjusted by an authorised dealer for
the duration of the trip.

lights:main beam headlights ...................................... (current page)
warning buzzer ...................................................... (current page)
see-me-home lighting ............................................ (current page)
lights mobile directional ............................................. (current page)
1.72
ENG_UD24014_3
Éclairages et signalisations extérieurs (X95 - B95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Jaune NoirNoir texte
EXTERIOR LIgHTINg AN d s I g NAL s (2/3)
1
special note:
– I f the dipped beam headlights are
manually switched on and if the light
is sufficient, the directional head-
lights will remain fixed;
–

I
f the lights come on automatically
when cornering, the directional
headlights will start working from the
next time the vehicle corners;
–

W
hen the dipped beam headlights
are switched on with the engine
running and the vehicle stationary,
the lights move to reinitialise them-
selves. If not, there is a system fault.
switching off the lights
There are two possibilities:
– Manually , move ring 2 to position 0;
–

a
utomatically, the lights will go out
when the engine is switched off, the
driver’s door is opened or the vehicle
is locked. In this case, the next time
the engine is started the lights will be
switched back on according to the
position of the ring

2
.
NB: if the fog lights are lit, the lights are
not switched off automatically.
“see-me-home lighting”
function
This function allows you to briefly switch
on the dipped beam headlights (to pro-
vide light when opening a gate, etc.).
With the engine and lights off and
ring

2
in the 0 position, pull stalk

1
to-
wards you: the dipped beam headlights
light up for approximately thirty sec-
onds. To increase this duration, you
may pull the stalk up to four times (total
time restricted to two minutes). The
message “See-me-home _ _ _” along
with the times the lights will be on for
is displayed on the instrument panel to
confirm this action.
To switch off the lights before they go
out automatically, turn ring
2 to any po-
sition, then return it to position 0.
directional headlights
Depending on the vehicle, with the
dipped beam headlights on and under
certain conditions (speed, steering
wheel angle, forwards gear selected,
etc.) when cornering, the dipped beam
headlights move to light the inside of
the bend.
Operating faults
When the message “Check lighting”,
accompanied by the
© warning
light is displayed on the instrument
panel, there is a lighting fault.
Consult an approved dealer.
2

lights:fog lights .......................................................... (current page)
JauneNoirNoir texte
1.73
ENG_UD24014_3
Éclairages et signalisations extérieurs (X95 - B95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
EXTERIOR LIgHTINg AN d s I g NAL s (3/3)
When driving in fog or snow, or
when transporting objects which are
higher than the roof, the headlights
do not come on automatically.
Switching on the fog lights remains
the responsibility of the driver: the
indicator lights on the instrument
panel inform you whether the fog
lights are lit (indicator light on) or not
(indicator light not on).
5
6
1
gfront fog lights
Turn centre ring 5 on stalk 1
until the symbol faces mark 6, then re-
lease it.
Operation of the fog lights depends on
the exterior lighting position selected,
and an indicator light will light up on the
instrument panel.
fRear fog light
Turn centre ring 5 on the stalk
until the symbol faces mark 6 , then re-
lease it.
Operation of the fog lights depends on
the exterior lighting selected, and an in-
dicator light will light up on the instru-
ment panel.
To avoid inconveniencing other road
users, remember to switch off the rear
fog light when it is no longer needed.
Lights-on reminder buzzer
If the lights are on after the engine is
switched off, a warning beep sounds
when the driver ’s door is opened to
warn you that the lights are still on.
switching off the lights
Turn ring 5 again until mark 6 is oppo-
site the symbol for the fog light that you
wish to switch off. The corresponding
indicator light on the instrument panel
goes out.
The front and rear fog lights switch off
when the exterior lights are switched
off.

electric beam height adjustment ........... (up to the end of the DU)
see-me-home lighting ........................... (up to the end of the DU)
lights: adjusting ......................................... (up to the end of the DU)
lights adjustment ...................................... (up to the end of the DU)
signals and lights .................................. (up to the end of the DU)
headlight beam adjustment .................. (up to the end of the DU)
1.74
ENG_UD6291_1
Réglage électrique de la hauteur des faisceaux (X95 - B95 - D95 -\
Renault)ENG_NU_837-8_BDK95_Renault_1
Headlight beam adjustment
On vehicles fitted with this function,
control A allows you to adjust the height
of the beams according to the load.
Turn control
A downwards to lower the
headlights and upwards to raise them.
For vehicles not fitted with control
A ,
adjustment is automatic.
ELEcTRIcAL A d JU s T m ENT O f THE d I pp E d BEA m HEA d LI g HT s
A
Examples of positions for adjusting
control A according to the load
f

ive door Three door
d

river alone or with front
passenger 0
0
d

river with one front
passenger and one rear
passenger 0
0
d

river with one front
passenger and two or three
rear passengers 1
1
d

river with one front
passenger, three rear
passengers and luggage 3
3

headlight washer ................................................... (current page)
1.76
ENG_UD17355_4
Essuie-vitre / lave-vitre avant (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Headlight washers
Headlights on
On equipped vehicles, hold stalk 1

pulled towards you for about 1 second,
and the headlight washers and wind-
screen washers will be activated at the
same time.
Note: when the minimum windscreen
washer fluid level is reached, the head-
light washer system may be deprimed.
Fill the windscreen washer fluid and
then activate the windscreen washer,
with the engine running , to reprime
the system.
Before any action on the
windscreen (washing the
vehicle, de-icing, cleaning
the windscreen, etc.) return
stalk

1 to position A (park).
Risk of injury and/or damage.
Windscreen washer
With the ignition on, pull stalk 1 then
release.
A
brief pull will trigger a single sweep
of the wipers, in addition to the wind-
screen washer.
A longer pull will trigger three sweeps
of the wipers followed, a few seconds
later, by a fourth, in addition to the wind-
screen washer.
WINdscREEN WAsH/WIpE (2/2)
1
In freezing or snowy weather, ensure
they are not stuck to the windscreen
(including the central area located
behind the interior rear-view mirror)
and the rear screen before starting
the wipers (risk of motor overheat-
ing).
A
B
c
d
1
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in position A (park).
Risk of injury.

JauneNoirNoir texte
1.79
ENG_UD23616_6
Réservoir à carburant (X95 - B95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
filling with fuelWith the ignition off, insert the nozzle to
open valve
A and insert it fully before
turning it on to fill the fuel tank (risk of
splashing).
Keep the nozzle in this position through-
out the entire filling operation.
When the pump cuts out automatically
at the end of the filling procedure, a
maximum of two further filling attempts
may be made, as there must be suffi-
cient space in the fuel tank to allow for
expansion.
Make sure that no water enters the fuel
tank during filling. The valve
A

and its
surround must remain clean.
p

etrol versions
Using leaded petrol will damage the
antipollution system and may lead to a
loss of warranty.
To ensure that the fuel tank is not filled
with leaded petrol, the fuel tank filler
neck contains a restrictor fitted with a
foolproof system which only allows
the nozzle for unleaded petrol to be
used (at the pump).
No modifications what -
soever are permitted on
any part of the fuel supply
system (computers, wiring,
fuel circuit, injector, protection
covers, etc.) as this may be danger-
ous (such work must be undertaken
by qualified Network personnel).
fUEL TANK (2/2)
Running out of fuel on diesel
versions
After a breakdown caused by com-
pletely running out of fuel, the system
must be reprimed before the engine is
restarted: Use bulb
1
.
The engine can now be restarted.
If the engine does not start after several
attempts, contact an approved Dealer.
1persistent smell of
fuel
If you notice a persistent
smell of fuel you should:
–

stop

the vehicle as soon as traf-
fic conditions allow and switch off
the ignition;
–

s

witch on the hazard warning
lights and ask your passengers
to leave the vehicle and to keep
away from traffic;
–

contact an approved Dealer
.