2016 RAM CHASSIS CAB buttons

WARNING!• A loose head restraint thrown forward in a colli-
sion or hard stop could cause serious injury or
death to occupants of the vehicle. Always securely
stow removed head restraints in a location outside
the occupant compartment.
• ALL the head restraints MUST be reinstalled in the
vehicle to properly protect the occupants. Follow
the re-installation instructions above prior to oper-
ating the vehicle or occupying a seat.
NOTE: Do not reposition the head restraint 180 degrees
to the incorrect position in an attempt to gain additional
clearance to the back of the head.Adjustment Buttons1 — Release Button
2 — Adjustment Button 3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153

NOTE:
• The rear center head restraint (Crew Cab and Quad
Cab) has only one adjustment position that is used to
aid in the routing of a tether. Refer to “Occupant
Restraints” in “Things to Know Before Starting Your
Vehicle” for further information.
• Do not reposition the head restraint 180 degrees to the
incorrect position in an attempt to gain additional
clearance to the back of the head.
WARNING!ALL the head restraints MUST be reinstalled in the
vehicle to properly protect the occupants. Follow the
re-installation instructions above prior to operating
the vehicle or occupying a seat.Release/Adjustment Buttons1 — Release Button
2 — Adjustment Button 3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155

DRIVER MEMORY SEAT — IF EQUIPPED
This feature allows the driver to store up to two different
memory profiles for easy recall through a memory
switch. Each memory profile contains desired position
settings for the driver seat, side mirrors, adjustable
pedals (if equipped) and a set of desired radio station
presets. Your Remote Keyless Entry (RKE) transmitter
can also be programmed to recall the same positions
when the UNLOCK button is pushed.
NOTE: Your vehicle is equipped with two RKE transmit-
ters, one RKE transmitter can be linked to memory
position 1 and the other transmitter can be linked to
memory position 2.
The memory seat buttons are located on the outboard
side of the drivers seat cushion. Programming The Memory Feature
To create a new memory profile, perform the following:
1. Cycle the vehicles ignition to the ON/RUN position
(do not start the engine). Memory Seat Buttons156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Adjust all memory profile settings to desired prefer-
ences (seat, side mirrors, adjustable pedals and radio
station presets).
3. Push and release the S (Set) button on the memory
switch.
4. Within five seconds, push and release either of the
memory buttons (1) or (2). The Electronic Vehicle
Information Center (EVIC) or Driver Information Dis-
play (DID) will display which memory position has
been set.
NOTE:
• Memory profiles can be set without the vehicle in
PARK, but the vehicle must be in PARK to recall a
memory profile.
• To set a memory profile to your RKE transmitter, refer
to “Linking And Unlinking The Remote Keyless Entry
Transmitter To Memory” in this section. Linking And Unlinking The Remote Keyless Entry
Transmitter To Memory
Your RKE transmitters can be programmed to recall one
of two pre-programmed memory profiles by pushing the
UNLOCK button on the RKE transmitter.
NOTE: Before programming your RKE transmitters to
memory the feature has to be selected.
• If your vehicle is equipped with a touchscreen, you
must select the “Memory To FOB” feature through the
Uconnect system. Refer to “Uconnect Settings ” in
“Understanding Your Instrument Panel” for further
information.
• If your vehicle is not equipped with a touchscreen, you
must select the “Key Fob Linked To Memory” feature
through the Electronic Vehicle Information Center
(EVIC) or Driver Information Display (DID). Refer to
“Electronic Vehicle Information Center (EVIC)” or 3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157

Driver One Memory Position Recall
• To recall the memory settings for driver one using the
memory switch, push MEMORY button number 1 on
the memory switch.
• To recall the memory settings for driver one using the
RKE transmitter, push the UNLOCK button on the
RKE transmitter linked to memory position 1.
Driver Two Memory Position Recall
• To recall the memory setting for driver two using the
memory switch, push MEMORY button number 2 on
the memory switch.
• To recall the memory settings for driver two using the
RKE transmitter, push the UNLOCK button on the
RKE transmitter linked to memory position 2.
A recall can be cancelled by pushing any of the MEMORY
buttons during a recall (S, 1, or 2). When a recall is cancelled, the driver’s seat, and the power pedals (if
equipped) stop moving. A delay of one second will occur
before another recall can be selected.
Easy Entry/Exit Seat
This feature provides automatic driver seat positioning to
enhance driver mobility when entering and exiting the
vehicle.
The distance the driver seat moves depends on where
you have the driver seat positioned when you remove the
Key Fob from the ignition (or change the ignition to OFF,
for vehicles equipped with Keyless Enter-N-Go).
• When you remove the Key Fob from the ignition (or
change the ignition to OFF, for vehicles equipped with
Keyless Enter-N-Go), the driver seat will move about
2.4 inches (60 mm) rearward if the driver seat position
is greater than or equal to 2.7 inches (67.7 mm) forward 3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159

The Electronic Speed Control buttons are located on the
right side of the steering wheel. NOTE: In order to ensure proper operation, the Elec-
tronic Speed Control System has been designed to shut
down if multiple Speed Control functions are operated at
the same time. If this occurs, the Electronic Speed Control
System can be reactivated by pushing the Electronic
Speed Control ON/OFF button and resetting the desired
vehicle set speed.
To Activate
Push the ON/OFF button. The Cruise Indicator Light in
the instrument cluster will illuminate. To turn the system
off, push the ON/OFF button a second time. The Cruise
Indicator Light will turn off. The system should be
turned off when not in use.Electronic Speed Control Switches1 — ON/OFF 3 — SET -
2 — RES + 4 — CANCEL 3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

▫ DID Messages ....................... .294
▫ DID Selectable Menu Items ............. .296
 CYBERSECURITY ...................... .310
 UCONNECT SETTINGS ................. .312
▫ Buttons On The Faceplate ............... .313
▫ Buttons On The Touchscreen ............. .314
▫ Customer Programmable Features — Uconnect 5.0
Personal Settings ..................... .314
▫ Customer Programmable Features — Uconnect
8.4A/8.4AN Personal Settings ........... .329
 UCONNECT RADIOS — IF EQUIPPED ..... .346
 iPod/USB/MP3 CONTROL — IF EQUIPPED . . .346
 STEERING WHEEL AUDIO CONTROLS — IF
EQUIPPED .......................... .347 ▫ Radio Operation ..................... .348
▫ CD Player — If Equipped ............... .348
 CD/DVD DISC MAINTENANCE .......... .348
 RADIO OPERATION AND MOBILE DEVICES . .349
▫ Regulatory And Safety Information ........ .349
 CLIMATE CONTROLS .................. .351
▫ Manual Climate Controls Without Touchscreen —
If Equipped ........................ .351
▫ Manual Climate Controls With Touchscreen — If
Equipped .......................... .356
▫ Automatic Climate Controls With Touchscreen —
If Equipped ........................ .361
▫ Climate Control Functions .............. .367
▫ Automatic Temperature Control (ATC) ..... .369230 UNDERSTANDING YOUR INSTRUMENT PANEL

The system allows the driver to select information by
pushing the following EVIC Control buttons located on
the left side of the steering wheel: • UP Arrow Button
Push and release the UP arrow button to scroll
upward through the main menu items.
• DOWN Arrow Button
Push and release the DOWN arrow button to
scroll downward through the main menu
items.
EVIC Control Buttons 4UNDERSTANDING YOUR INSTRUMENT PANEL 269