2016 Peugeot Expert VU stop start

281
Expert_en_Chap07_info-pratiques_ed01-2016
Checks
12 V battery
the battery does not require any maintenance.
However, check regularly that the terminals
are correctly tightened (versions without quick
release terminals) and that the connections
are clean.Refer to the manufacturer's
service schedule for details of the
replacement intervals for these
components.
Air filter and passenger compartment filter
Replace the oil filter each time the
engine oil is changed.
Refer to the manufacturer's
service schedule for details of
the replacement interval for this
component.
Oil filterParticle filter (Diesel)
the start of saturation of the particle
filter is indicated by the temporary
illumination of this warning lamp
accompanied by a message in the
multifunction screen.
As soon as the traffic conditions permit,
regenerate the filter by driving at a
speed of at least 40 mph (60 km/h) until
the warning lamp goes off.
If the warning lamp stays on, this
indicates a low additive level.
For more information on Checking
levels , refer to the corresponding
section.
on a n

ew vehicle, the first particle
filter regeneration operations may be
accompanied by a "burning" smell,
which is per fectly normal.
Following prolonged operation of the
vehicle at very low speed or at idle,
you may, in exceptional circumstances,
notice the emission of water vapour at
the exhaust on acceleration.
t
h
is does
not affect the behaviour of the vehicle
or the environment.un
less otherwise indicated, check these components in accordance with the manufacturer's
service schedule and according to your engine.
ot

her wise, have them checked by a PE
u

g
Eo

t
dealer or a qualified workshop.
For more information and the precautions to
take before starting work on the 12 V batter y ,
refer to the corresponding section. Depending on the environment (e.g. dusty
atmosphere) and the use of the vehicle
(e.g.

city driving), replace them twice as often
if necessary .
A clogged passenger compartment filter may
have an adverse effect on the per formance
of the air conditioning system and generate
undesirable odours.
Versions equipped with Stop & Start are
fitted with a 12 V lead-acid battery of
specific technology and specification.
Its replacement should be carried
out only by a PE
u

g
Eo

t
dealer or a
qualified workshop.
7
Practical information

286
Expert_en_Chap07_info-pratiques_ed01-2016
F After emptying the bottle, wipe away any spillage around the tank filler using a damp
cloth. If any additive is split or splashed, wash
immediately with cold water or wipe with
a damp cloth.
If the additive has crystallised, clean it
off using a sponge and hot water.
F
R
efit the blue cap to the tank and turn it
a 6
th of a turn clockwise, to its stop.Important: when topping-up after
running out of additive
, signalled
by the message "
to
p up emissions
additive: Starting prevented", you
must wait for about 5 minutes before
switching the ignition on again, without
opening the driver's door, unlocking
the vehicle, introducing the remote
control key into the ignition switch,
or placing the electronic key of the
"Keyless Entr y and Star ting" system
inside the vehicle.
Switch on the ignition, then wait for
10


seconds before starting the engine.
F
o
b

tain a bottle of AdBlue
®. After first
checking the use-by date, read carefully
the instructions on use on the label before
pouring the contents of the bottle into your
vehicle's AdBlue
® tank.
Freezing of the AdBlue
®
AdBlue® freezes at temperatures below
around -11°C.
th

e SCR system includes a heater
for the AdBlue
® tank, allowing you to
continue driving in very cold conditions. F
R efit the black cover, starting at the top.
F

C
lose the door.
Practical information

321
Expert_en_Chap08_En-cas-de-panne_ed01-2016
12 V batterythe battery is located under the bonnet.
F op en the bonnet using the interior release
lever, then the exterior safety catch.
F

S
ecure the bonnet stay.
Access to the battery
Procedure for starting the engine using another
battery or charging a discharged battery.
General points
Lead-acid starter batteries
Protect your eyes and face before
handling the battery.
All operations on the battery must be
carried out in a well ventilated area and
away from naked flames and sources
of sparks, so as to avoid the risk of
explosion or fire.
Wash your hands afterwards.
Versions equipped with Stop & Start are
fitted with a 12 V lead-acid battery of
specific technology and specification.
Its replacement should be carried
out only by a PE
u

g
Eo

t
dealer or a
qualified workshop. If your vehicle has an automatic
gearbox, do not try to start the engine
by pushing the vehicle.
Batteries contain harmful substances
such as sulphuric acid and lead.
th

ey must be disposed of in
accordance with regulations and must
not, in any circumstances, be discarded
with household waste.
ta

ke used remote control batteries and
vehicle batteries to a special collection
point.
For more information on the Bonnet
and Engine , refer to the corresponding
section(s).
F

I
f fitted to your vehicle, remove the plastic
cover to access the (+) terminal.
th

e battery (-) terminal is not accessible.
A remote earth point is provided at the front of
the vehicle.
8
In the event of a breakdown

322
Expert_en_Chap08_En-cas-de-panne_ed01-2016
Starting using another
battery
Never try to start the engine by
connecting a battery charger.
Never use a 24 V or higher battery
b o o s t e r.
First check that the slave battery has a
nominal voltage of 12 V and a capacity
at least equal to that of the discharged
battery.
th
e two vehicles must not be in contact
with each other.
Switch off the electrical consumers on
both vehicles (audio system, wipers,
lighting, ...).
Ensure that the jump lead cables do
not pass close to moving parts of the
engine (cooling fan, belts, ...).
Do not disconnect the (+) terminal when
the engine is running. F

R
aise the plastic cover on the (+) terminal,
if your vehicle has one.
F

C
onnect the red cable to the positive
terminal (+) of the flat battery A (at
the metal elbow) then to the positive
terminal
(+) of the slave battery B or the
b o o s t e r.
F

C
onnect one end of the green or black
cable to the negative terminal (-) of the
slave battery B or the booster (or earth
point on the other vehicle).
F

C
onnect the other end of the green or black
cable to the earth point C on the broken
down vehicle.
F

S
tart the engine of the vehicle with the
good battery and leave it running for a few
minutes.
F
o
p
erate the starter on the broken down
vehicle and let the engine run.
If the engine does not start straight away,
switch off the ignition and wait a few moments
before trying again.
When your vehicle's battery is discharged, the
engine can be started using a slave battery
(external or on another vehicle) and jump lead
cables or a battery booster.
Some functions, including Stop & Start,
are not available if the battery is not
sufficiently charged.
F

W
ait until the engine returns to idle then
disconnect the jump lead cables in the
reverse order.
F
R
efit the plastic cover to the (+) terminal, if
your vehicle has one.
F
A
llow the engine to run for at least
30 minutes, by driving or with the vehicle
stationary, so that the battery reaches an
adequate state of charge.
In the event of a breakdown

323
Expert_en_Chap08_En-cas-de-panne_ed01-2016
For optimum service life of the battery, it is
essential to maintain an adequate state of
charge.
In some circumstances it may be necessary to
charge the battery:
-
i
f you use your vehicle essentially for short
journeys,
-

i
f the vehicle is to be taken off the road for
several weeks.
Contact a PE
u

g
Eo
t dealer or a qualified
workshop.
Charging the battery using
a battery charger
F Switch off the ignition.
F S witch off all electrical consumers (audio
system, lighting, wipers, ...).
If you envisage charging your vehicle's
battery yourself, use only a charger
compatible with lead-acid batteries of a
nominal voltage of 12 V. Follow the instructions for use provided
by the manufacturer of the charger.
Never reverse polarities.
Never try to charge a frozen battery.
If the battery has been frozen, have it
checked by a PE
u
g
Eo
t dealer or a
qualified workshop, who will check that
the internal components have not been
damaged and the casing is not cracked,
which could cause a leak of toxic and
corrosive acid.
If this label is present, it is essential
to use only a 12 V charger, to avoid
causing irreversible damage to the
electrical components related to the
Stop & Start system. It is not necessary to disconnect the
battery.
F
S
witch off the charger B before connecting
the cables to the battery, so as to avoid any
dangerous sparks.
F

E
nsure that the charger cables are in good
condition.
F

R
aise the plastic cover, if your vehicle has
one, on the (+) terminal. F

C
onnect the charger B cables as follows:
-
t
he positive (+) red cable to the
(+) terminal of the battery A
,
-
t
he negative (-) black cable to the earth
point C on the vehicle.
F
A
t the end of the charging operation, switch
off the charger B before disconnecting the
cables from the battery A .
8
In the event of a breakdown

324
Expert_en_Chap08_En-cas-de-panne_ed01-2016
Do not force the lever as locking will
not be possible if the clamp is not
positioned correctly; start the procedure
again.
Disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of service for a long
period.
Wait 2 minutes after switching off the ignition
before disconnecting the battery.
F
c
lose the windows and the doors before
disconnecting the battery,
F

s
witch off all electrical consumers (audio
system, wipers, lighting, ...),
F

s
witch off the ignition and wait for
four


minutes.
Having exposed the battery, it is only
necessary to disconnect the (+) terminal.
Quick release terminal
Disconnecting the (+) terminal
F Raise the lever A fully to release the clamp B.
Following reconnection of the battery
Reconnecting the (+) terminal
F Position the open clamp B of the cable on
the positive post (+) of the battery.
F

P
ress down on the clamp to position it
correctly on the battery post.
F

L
ock the clamp by lowering the lever A .After reconnecting the battery, switch on the
ignition and wait 1 minute before starting to
allow initialisation of the electronic systems.
However, if minor problems persist following
this operation, contact a PE
u

g
Eo
t dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise or reset certain
systems, such as:
-
t
he remote control or electronic key
(depending on version),
-
t
he electric windows,
-
t
he date and time,
-
t
he radio preset stations.th
e Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the ambient
temperature and the state of charge of
the battery (up to about 8 hours).
In the event of a breakdown

502
the table below gives answers to the most frequently asked questions on your audio system.QUESTION ANSWER SOLUTION
With the engine off, the
audio system switches off
after a few minutes of use. When the engine is switched off, the audio system operating time
depends on the state of charge of the battery.
th

e switch-off is normal: the audio equipment switches to economy
mode and switches off to prevent discharging of the vehicle's
battery. Start the vehicle's engine to increase the battery
charge.
th

e message "the audio
system is overheated"
appears on the display. In order to protect the installation if the surrounding temperature
is too high, the audio system switches to an automatic thermal
protection mode leading to a reduction in volume or CD play
stopping. Switch the audio system off for a few minutes to
allow the system to cool.
Frequently asked questions
QUESTION
ANSWER SOLUTION
th

ere is a difference in
sound quality between the
different audio sources
(radio, CD...). For optimum sound quality, the audio settings (Volume, Bass,
tr

eble, Ambience and Loudness) can be adapted to the different
sound sources, which may result in audible differences when
changing source (radio, CD...). Check that the audio settings (Volume, Bass,
tr

eble, Ambience and Loudness) are adapted to
the sources listened to. It is advisable to set the
audio functions (Bass,
t
r
eble, Front-Rear Balance
and Left-Right Balance) to the middle position,
select the musical ambience "None" and set the
loudness correction to the "Active" position in CD
mode or to the "Inactive" position in radio mode.
Radio
Audio and telematics

511
Expert_en_Chap11_index-alpha_ed01-2016
table of weights ........................... 333 , 335, 336tab
le position ................................................ 101
ta

bles of fuses .............................. 316, 317, 320
ta

ble top, working
...............................
..........109
t

a n k , f u e l

....................................................... 265
te

chnical data

.............................. 333, 335, 336
T
telephone ............400, 402, 404, 406 - 411, 456,
458, 460, 462- 467, 497, 498, 500
te

lephone, Bluetooth with voice
recognition


.................................................. 501
te

mperature, coolant

................................19, 31
th

ird brake lamp

................................... 311, 314
thr

ee flashes (direction indicators)

..............148
tim

e (setting)
..............................
....46, 421, 477
tM

C (
tr
affic info)
.......................................... 3

67
to

ol box

................................. 287, 289, 290, 296
to

o l s

..................................................... 290, 296
to

pping-up the AdBlue
® additive ................. 28 5to
tal distance recorder
................................... 38
to

uch screen ................ 39, 43, 44, 89, 150 -152,
154, 158, 220, 226, 236, 245, 247, 249, 250, 254, 256, 264, 341, 429
to

w b a r


.......................................... 198, 269, 272
to

wed loads


................................. 333, 335, 336
to

wing another vehicle
......................... 325

, 326
to

wing eye

.................................................... 325
tra

ction control (ASR)


............................ 25, 161
tr

affic information (
tA

)


................................. 489
tr

affic information (
tM

C)
.............................. 3

67
t

r a i l e r


.................................................... 198, 269
tr

iangle, warning ........................................... 287
tr

ip computer


............................................ 40 - 42
tr

ip distance recorder


..................................... 38
ty

pe of bulbs

................................................. 3

03
ty

r e s


................................................................ 12
ty

re under-inflation
detection


...................... 22, 262, 264, 295, 302
Speedometer


.............................................
14 -16
Stability control (ESC)............................. 25, 161
Starting the engine


.......................................
19 9
Starting the vehicle


......
202, 204, 206, 209, 214
Station, radio
........................ 3

94, 395, 450, 451
Stay, bonnet


..................................................
276
Steering mounted controls, audio


..................................
344, 432, 485, 486
Steering wheel, adjustment


............................
99
Stop


.................................................................
18
Stopping the vehicle
............
202, 204, 209, 214
Stop & Start
........................ 22, 29, 42, 132, 135,
218, 220, 265, 276, 281, 321, 324
Stop (warning lamp)
........................................ 18
St

orage


.................................. 105, 109, 117, 120
Storage compartments
......................... 12

0, 121
Storage wells


......................................... 117, 1 2 0
Stowing rings


................................................ 12 2
Sun visor


....................................................... 11 9
Switching off the engine
............................... 19

9
Synchronising the remote control


............. 54, 70
Screenwash


..................................................
15 8
Screenwash, rear


..........................................
157
SCR (Selective Catalytic Reduction)


............
283
SCR system

..................................................
283
Seat and bench seat, rear, fixed
........... 11

3 , 11 6
Seat and bench seat, rear, on rails

..............
11 6
Seat belts
...................... 1

66, 168, 169, 180, 181
Seat belts, rear


..............................................
167
Seat, front bench, 2-seat


......................
104, 167
Seat, rear bench


...........................................
11 6
Seats, electric
...............................................
102
Seats, front ...............................
....... 99, 101, 102
Seats, front bench
......................................... 105
Seats, heated


........................................ 103, 105
Seats, rear


............................................. 11 0 , 113
Selector, gear


................................................ 214
Serial number, vehicle
.................................. 3

37
Service


............................................................ 28
Service indicator


....................................... 31, 3 3
Service (warning lamp)
................................... 28
S

ervicing
...............................

.......................... 12
Settings
...............

.. 412, 414, 416, 468, 470, 472
Settings, system


.................................... 420, 476
Sidelamps


............. 146, 304-306, 310, 313, 315
Side repeater
..............................

.................. 305
Sliding side door, electric


............................ 49, 57, 64, 65, 78 - 84
Sliding side door, hands-free

.............. 87

, 89, 90
Sliding side door, manual


......................... 75 -77
Sliding side window


...................................... 124
Snow chains
......................................... 26

2, 268
Snow chains, link
.......................................... 26

8
Socket, 12 V accessory

................................ 12

1
Socket, auxiliary


........................... 398, 454, 494
Socket, JACK


....................... 122, 398, 454, 494
Sockets, audio


.............................................. 12 2
Speed limiter


................................. 224, 227, 229
Speed limit recognition


................. 225, 226, 229, 232, 236
.
Alphabetical index