2016 Peugeot Boxer wheel

158
boxer_en_Chap08_Aide-Rapide_ed01-2015
- extend the jack using the wheelbrace d
and trhe bar B until the wheel is a few
centimetres off the ground.
-
u nscrew the bolts fully and remove the
wheel to be repaired.
-
Position the jack
c at one of the four

locations provided on the underbody
near the wheels.
If your vehicle has a folding foot board, the
jack must be positioned at 45°.
removing the wheel to be repaired
- Remove the trim (depending on version)
using the screwdriver E as a lever.
-

Release the bolts using the

wheelbrace
d
and the bar

B.
Puncture

159
boxer_en_Chap08_Aide-Rapide_ed01-2015
Fitting the spare wheelStowing the wheel
- Put the spare wheel in place on the hub
and fit the bolts by hand.
-

Pre-tighen the bolts using the

wheelbrace
d and the bar

B.
-

Lower the vehicle completely by folding

the jack
c
, then remove the jack.
-

t
ighten the bolts again using the

wheelbrace
d and the bar

B (tighten
them fully without forcing them). You must place the wheel to be repaired or
the spare wheel under the vehicle to secure
the carrier system.
-
Place the wheel at the rear of the vehicle.
●


For eversions with
steel wheels, hook
the carrier H on the outside.
●

Screw in the grip
G to secure the carrier
and wheel. ●
For versions with alloy wheels, position
the strap j
on the outside.
●


Fit the three strap fixing screws
I to the
alloy wheel.
Puncture
QuICK HeLP
8

160
boxer_en_Chap08_Aide-Rapide_ed01-2015
Refer to the "technical data -
Identification markings" section for the
location of the tyre pressure label.
-
Fit the long socket
A
, the wheelbrace
d

and bar B to the securing screw.
-
t
urn the assembly clockwise to fully


draw in the cable and raise the wheel
under the vehicle.
-

Check that the wheel is positioned


horizontally flat against the floor of the
vehicle and that the the cut-out for the
carrier system is visible.
-

Stow the tools and the trim (depending


on version).
refitting the repaired wheel
Refitting the repaired wheel is the same as
fitting the spare wheel; don't forget to refit
the wheel trim.
t

he spare wheel is not designed to be used
over long distances. Have the tightening
of the bolts and pressure of the spare
wheel checked by a P
euge O t
dealer or a

qualified workshop without delay.
Also, have the original wheel repaired and
refitted by a P
euge O t
dealer or a qualified

workshop as soon as possible.
Puncture

163
boxer_en_Chap08_Aide-Rapide_ed01-2015
toWI n G
t
owing the vehicle
the removable towing eye is located in the
tool box under the front passenger seat.
u

nclip the cover using a flat tool.
Screw the removable towing eye in fully.
Attach the approved towing arm to to the
removable towing eye.
Place the gear lever in neutral.
towing another
vehicle
the fixed towing eye is located on the right
below the bumper .
Attach the approved towing arm to the fixed
eye.
Failure to observe this requirement
may result in damage to certain braking
components and the lack of some braking
assistance systems when the engine is
re-started.
General recommendations
Observe the legislation in force in your
country.
e

nsure that the weight of the towing vehicle
is higher than that of the towed vehicle.
t

he driver must remain at the wheel of the
towed vehicle and must have a valid driving
licence.
When towing a vehicle with all four wheels
on the ground, always use an approved
towing arm; rope and straps are prohibited.
t

he towing vehicle must move off gently.
When towing a vehicle with the engine off,
there is no longer any power assistance for
braking or steering.
In the following cases, you must always call
on a professional recovery service:
-

vehicle broken down on a motorway or

fast road,
-

four-wheel drive vehicle,
-


when it is not possible to put the

gearbox into neutral, unlock the
steering, or release the parking brake,
-

towing with only two wheels on the

ground,
-

where there is no approved towing arm

available...
Being towed or towing
QuICK HeLP
8

164
boxer_en_Chap08_Aide-Rapide_ed01-2015
toWBA r WI t H Q u I c KLY
d E t
A
c HABLE to WBALL
Presentation
this towball can be fitted and removed
quickly and easily without the use of tools. For information on the maximum

trailer weight and the recommended
nose weight, refer to the " t
echnical data -

Weights" section.
For information on safely towing a trailer,
refer to the "Accessories -
towing a trailer"


section.
1.
Carrier.
2.

Connector socket.
3.


Safety eye.
4.


Detachable towball.
5.


Locking / unlocking wheel.
6.


Key lock.
7.


Key reference label. A.


Locked
position; the locking wheel is in
contact with towball (no gap).
B.
u
nlocked position; the locking wheel
and towball are no longer in contact
(gap of about 5 mm). Before each use
Check that the towball is correctly
locked and verify the following points:
- the green mark on the locking wheel
is in line with the green mark on the
towball,
-

the locking wheel is in contact with the

towball,
-

the key lock is on and the key removed;

the locking wheel can no longer be
operated,
-

the towball must no longer move at all in

its carrier; try to shake it by hand.
d

uring use
Never unlock the device when a trailer or
load carrier is fitted to the towball.
Never exceed the maximum authorised
weight for the vehicle (the
g ross Vehicle
Weight -
g VW), the trailer, or the sum of the
two (the
g ross
train W
eight - gt W).
Observe the legislation in force in the
country in which you are driving. After use
For journeys made without a trailer or load
carrier, the towball must be removed and
the blanking plug inserted in the carrier.
t

his
measure applies particularly if the towball
could hinder visibility of the number plate or
lighting.
transport solutions

165
boxer_en_Chap08_Aide-Rapide_ed01-2015
Fitting the towball
Below the rear bumper, remove the
protective plug from the towball carrier.Insert the end of the towball 4
into the
carrier 1 and push upwards; it locks in place
automatically. Check that the mechanism has correctly
locked in to place (position A
).
Close the lock 6 using the key.
t

he locking wheel 5 turns a quarter of a turn
anti-clockwise; take care to keep your hands
clear. Always remove the.
t

he key cannot be
removed when the lock is open.
Clip the cap onto the lock.
transport solutions
QuICK HeLP
8

167
boxer_en_Chap08_Aide-Rapide_ed01-2015
grasp the towball 4 firmly with one hand;
with the other hand, pull and turn the locking
wheel 5 clockwise as far as it will go; do not
release the locking wheel.
Maintenance
Correct operation is only possible if the
towball and its carrier remain clean.
Before cleaning the vehicle with a high
pressure jet wash, the towball must be
removed and the blanking plug inserted in
the carrier.
Apply the label provided to a clearly
visible area, close to the carrier or in
the boot.
For any work on the towbar, got to a
P
euge O t
dealer or a qualified workshop.
Refit the protective blanking plug to the


carrier.
Carefully stow the towball in its bag away
from knocks and dirt.
e

xtract the towball from the bottom of its
carrier 1.
Release the locking wheel; this automatically
stops in the unlocked position (position B ).
transport solutions
QuICK HeLP
8

173
boxer_en_Chap09_Caracteristiques-techniques_ed01-2015
dIMEnSIonS
the dimensions are given in millimetres.
t

his model is available in 4 lengths (L1...) and 3 heights (H1...); r\
efer to the corresponding tables:
VA
n
L1L2L3L4
H1 H2 H1 H2 H2 H3 H2 H3
L Overall length 4

9635
4135
9986
363
H Overall height 2
254 2 524 2 254 2 524 2 524 2 764 2 524 2 764
A Wheelbase 3
0003
4504
035
B Front overhang 948
cRear overhang1

0151
380
dOverall width (incl./excl. mirrors)2 508 / 2

050
E Width of front track 1
810
F Width of rear track 1
790
G Height of load floor 535 to 565
I Length of interior floor 2
6703
1203
7054
070
jMaximum interior load height1

662 1 932 1 662 1 932 1 932 2 172 1 932 2 172
K Maximum interior width 1
870
M Interior width between wheel arches 1
422
Volume (m
3) 89.5 10 11.5 13 15 15 17
9
teCHNICAL DAtA
Dimensions