2016 Peugeot Boxer bulb

151
boxer_en_Chap08_Aide-Rapide_ed01-2015
Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not touch
the bulb directly with your fingers, use a
lint-free cloth.
When each operation has been completed,
check the operation of the lamps.
5 - Front foglamps
type E

, H11 - 55 W
-
t
urn the steering so that the wheel


on the side in question is turned fully
inwards.
-

Remove the screw located in the wheel


arch.
-

Remove the protective cover

.
LE
d
daytime running lamps
t

hese light-emitting diode (L
e
D) lamps
serve as both daytime running lamps and
sidelamps.
If your vehicle is fitted with L
e
D daytime
running lamps, contact a P
euge
O
t
dealer

.
4 - Sidelamps / daytime running lamps
type A

, W21/5W - 21W and 5W
-

Remove the cover by pulling on the


rubber tongue.
-
t
urn the bulb holder a quarter of a turn


anti-clockwise.
-

Change the bulb.
-


Remove the fixing clip and disconnect

the electrical connector.
-
t
urn and disengage the bulb holder
.
-

Change the bulb taking care to align the

metal part with the grooves on the lamp.
Failed bulb or lamp
QuICK HeLP
8

152
boxer_en_Chap08_Aide-Rapide_ed01-2015
courtesy lamps
type c , 12 V 10 W - 10 W
-
Press at the points indicated by the

arrows, then remove the courtesy lamp.
-

Open the protective flap.
-


Change the bulb moving aside the two

contacts.
-
e nsure that the new bulbs are secured
correctly between the two contacts.
-

Close the protective flap.
-


Fix the courtesy lamp in its housing and

ensure that it is secured correctly.
Side marker lamps
type A, W5W - 5W
-
If your vehicle is fitted with these lamps

(L4 body), remove the two fixing screws.
-

Pull the bulb holder to release it from the

lugs.
-

Pull the bulb out and change it.
direction indicator side
repeaters
type A , W 16 W F - 16 W
-
Move the mirror glass to access the

screws.
-

Remove the two fixing screws.
-


Pull the bulb holder to release it from the

lugs.
-

Pull the bulb out and change it. Front /

r ear
Failed bulb or lamp

153
boxer_en_Chap08_Aide-Rapide_ed01-2015
rear lamps
Carry out these operations in reverse order
to fit the new bulb.
1.
Brake lamps
type B,

P21W - 21W
2.

Brake/sidelamps
type B,

P 21/5W - 21W and 5W
3.
d
irection indicators
type B,

PY 21W - 21W
4.
r
eversing lamps
type A,

W16W - 16W
5.

Foglamp
type A,

W16W - 16W -

Identify the failed bulb then open the

rear doors.
-
Remove the corresponding access cover

by removing the seven fixing screws
(van) or
Remove the corresponding access cover


by pulling on its grip to unclip it (combi).
-

Disconnect the electrical connector by

pressing on its central tongue.
-

Remove the two fixing nuts of the lens.
-


Pull the lens from the outside.-


Remove the six bulb holder fixing

screws.
-
Spread the three retaining tongues and

remove the bulb holder from its housing.
-
Change the bulb.
For more information on the bulbs,

refer to the table " t
ypes of bulb or

lamp".
Failed bulb or lamp
QuICK HeLP
8

154
boxer_en_Chap08_Aide-Rapide_ed01-2015
third brake lamp
type A, W5W - 5W (x 4)
-
Remove the two lamp fixing screws.
-


Remove the lamp by pulling it towards

you.
number plate lamps
type c , C5W - 5W
-
Press the point, indicated by the arrow
,
then remove the plastic lens.
-

Remove the failed bulb by moving aside

the two contacts.
-

With the new bulb in place, ensure that

it is secured correctly between the two
contacts.
-

Replace the plastic lens and press on it

to lock it in place. -

Remove the bulb holder by squeezing

the two tabs.
- Remove the failed bulb by pulling it out.
-

Change the bulb.
Failed bulb or lamp

251
boxer_en_Chap11_Particularites_ed01-2015
PrESEntAtI on
Chassis cab and floor cab versions have a cab, a fixed floor and two spe\
cific rear lamp
clusters.
t

hese versions are also available with:
-

a crew cab,
-


a tipper body
.
changing a bulb
For more information on bulbs, refer to
the table "t
ypes of bulb and lamp" in

the "Quick help" section.
r
ear lamps
Carry out the operations in reverse order to
refit each bulb.
1.
d
irection indicators
type B,

PY21W - 21W
2.

Brake lamps
type B,

P21W - 21W
3.

Sidelamps
type A,

W5W - 5W
4.
r
eversing lamps
type A,

W16W - 16W
5.

Foglamps
type A,

W16W - 16W-

Identify the failed bulb.
-


Remove the four lamp unit fixing screws.
-


Pull the lamp unit out towards you.
-


Replace the bulb.
For more information on these versions, refer to the corresponding secti\
on.
SPeCIAL FeAtuReS
Chassis cab / Floor cab

12
Driving safely
boxer-post-it_en_Chap05_Securite_ed01-2015
TRAFFIC SIGN RECOGNITION
This system is a driving aid that make
use of a camera located at the top of the
windscreen.
The camera detects the following types of
traffic signs and displays the corresponding
information in the instrument panel:
- speed limits,
- no overtaking.
The units for the speed limits (mph or
km/h) depend on the country you are
driving in.
It should be taken into account so that you
observe the speed limit.
For the system to operate correctly when
you change country, the units for speed in
the instrument panel must be those for the
country you are driving in.
The automatic reading of traffic signs is
a driving assistance system and does
not always display speed limits correctly.
The speed limit signs present on the road
always take priority over the display by the
system.
The system cannot in any circumstances
replace the need for vigilance on the part of
the driver.
The driver must observe the driving
regulations and must adapt the speed of the
vehicle to suit the weather and traffic.
It is possible for the system to not display
the speed limit if it does not detect a speed
limit sign within a preset period.
The system is designed to detect signs that
conform to the Vienna Convention on traffic
signs.
To maintain correct operation of the
system:
- Regularly clean the area in front of the
camera.
- Do not carry out any repairs to the area
of the windscreen close to the camera
lens.
When replacing headlamp bulbs, you
are strongly recommended to fit genuine
replacement parts.
The use of other bulbs could reduce the
performance of the system.