2016 Peugeot 508 Hybrid key battery

74
508_en_Chap02_ouvertures_ed01-2016
Reinitialising the electric
windows
Always remove the key from the ignition
when leaving the vehicle, even for a
short time.
In the event of contact during operation
of the windows, you must reverse the
movement of the window. t
o d
o this,
press the switch concerned.
When operating the passenger electric
window switches, the driver must
ensure that no one is preventing correct
closing of the windows.
th

e driver must ensure that the
passengers use the electric windows
c o r r e c t l y.
Be aware of children when operating
the windows.
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
th

e safety anti-pinch function is not active
during these operations:
-
l

ower the window completely, then raise
it, it will rise in steps of a few centimetres
each time the switch is pressed. Repeat
the operation until the window closes
completely,
-

c

ontinue to press the switch for at least
one

second after reaching this position,
window closed.
Access

165
508_en_Chap06_conduite_ed01-2016
For Diesel vehicles, in very cold
weather the engine will not start
until the pre-heater warning
lamp has gone off.
If this warning lap comes on
after pressing the "S TA R T/
STOP " button, you should
maintain pressure on the brake
or clutch pedal until the warning
lamp goes off and not press the
" START/STOP " button, until the
engine starts. If the vehicle is not immobilised, the
engine will not stop.
Switching off
F Immobilise the vehicle.
F
W
ith the electronic key inside
the vehicle, press the " S TA R T/
STOP " button.
th

e engine stops and the steering column is
locked.
Ignition on (accessory) position
With the electronic key inside the vehicle,
press the "StA Rt/ StO P" button, with no
action on the pedals, to switch the ignition
on or off and so allow the use of the ancillary
equipment.
If one of the starting conditions is not
met, a reminder message appears in
the instrument panel screen. In some
circumstances, it is necessary to turn
the steering wheel slightly while pressing
the "S
tA

R
t/

S
tO

P" button to assist
unlocking of the steering; a message
warns you when this is needed.
F

W

ith the electronic key inside the vehicle,
press the brake pedal on vehicles with
automatic gearbox, or depress the clutch
pedal fully on vehicles with a manual
gearbox, then maintain pressure until the
engine starts.
Starting
F Press the " START/STOP"
button.
Starting-switching off the engine
using the electronic key
F the steering column is unlocked and the engine starts more or less immediately. If you use the accessory position for
too long, the system will automatically
go into energy economy mode to avoid
discharging the battery.
6
Driving

181
508_en_Chap06_conduite_ed01-2016
Going into engine START mode
the "ECO" indicator lamp goes off
and the engine starts automatically:
-

w

ith a manual gearbox , when you fully
depress the clutch pedal,
-

w

ith an automatic gearbox:
●

g

ear selector in position D or M , when
you release the brake pedal,
●

o

r gear selector in position N and brake
pedal released, when you put the gear
selector in position D or M ,
●

o

r when you engage reverse gear. StA
Rt mode is invoked automatically when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he speed of the vehicle exceeds 18 mph
(25 km/h) with a manual gearbox (2 mph
(3 km/h) with the
t
H
P 165 version), or
2
mph (3 km/h) with an automatic gearbox,
-

t
he electric parking brake is being applied,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.
Special cases: START invoked
automatically
In this case the "ECO" indicator lamp
flashes for a few seconds, then goes
of f.
This operation is perfectly normal.
Special cases: STOP mode not
available
StOP mode is not invoked when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he vehicle is stopped on a steep slope
(up
or down),
-

t
he electric parking brake is applied or
being applied,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-
d

emisting is selected,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
In this case, the "ECO" indicator
lamp flashes for a few seconds then
goes off.
This operation is perfectly normal.
6
Driving

256
508_en_Chap08_en-cas-de-pannes_ed01-2016
Do not force the lever as locking will
not be possible if the clamp is not
positioned correctly; start the procedure
again.
Disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of service for a long
period.
Wait 2 minutes after switching off the ignition
before disconnecting the battery.
F
c
lose the windows and the doors before
disconnecting the battery,
F

s
witch off all electrical consumers (audio
system, wipers, lighting, ...),
F

s
witch off the ignition and wait for
four


minutes.
Having exposed the battery, it is only
necessary to disconnect the (+) terminal.Following reconnection of
the battery
After reconnecting the battery, switch on the
ignition and wait 1 minute before starting to
allow initialisation of the electronic systems.
However, if minor problems persist following
this operation, contact a P
e

uge
Ot
dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise or reset certain
systems, such as:
-

t
he remote control or electronic key
(depending on version),
-

t
he electric blind(s),
-

t
he electric windows
-

t
he date and time,
-

t
he radio preset stations.
Quick release terminal
Disconnecting the (+) terminal
F Ra ise the lever A fully to release the
clamp


B.
Reconnecting the (+) terminal
F

P
osition the open clamp B of the cable on
the positive post (+) of the battery.
F

P
ress down on the clamp to position it
correctly on the battery post.
F

L
ock the clamp by lowering the lever A .
th

e Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the ambient
temperature and the state of charge of
the battery (up to about 8 hours).
In the event of a breakdown

257
508_en_Chap08_en-cas-de-pannes_ed01-2016
Removing - refitting the battery*
* Valid only for Saloon, SW and non-hybrid
RHX.
th

is procedure allows you to safely remove the
battery when needed to change a failed bulb.
You can also call on a P
e

uge
Ot


dealer or a qualified workshop to carry
out this procedure.
Before removal
- Place the vehicle in a ventilated location, with free access and preferably on a level
sur face.
-

A
pply the parking brake.
-

P
ut the gear lever into neutral (position N
for an automatic gearbox).
-

I
f the vehicle has an alarm, leave the
bonnet open to avoid triggering the alarm.
-

L
eave at least one window open if in a
secure location, other wise lock all the
doors and the boot. -
I f the vehicle has a motorised tailgate,
it will not be possible to open it after
disconnecting the battery.
-

S
witch off the ignition and remove the key.
-

I
f the vehicle has Keyless e
n
try and
Starting, take the remote control at least
3
metres away from the vehicle.
-

W
ait about 4 minutes (or 12 minutes
with an automatic gearbox) before
disconnecting the battery.
8
In the event of a breakdown

14
Hybrid4 system
508HY-comp_en_Chap00b_hybrid_ed01-2016
Never leave children alone inside the vehicle when the HYbrid4 system is active.
The RE ADY can come on after a RE ADY can come on after a RE ADYfew seconds if the HYbrid4 system is activated after going into energy economy mode.
Starting - switching off the HYbrid4 system
Starting the HYbrid4 system
Activation of the HYbrid4 system
In wintry conditions with the engine cold, the Diesel pre-heating warning lamp can stay on for a few seconds; wait until it goes off before releasing the brake pedal.
In the event of non-activation of the HYbrid4 system:  If N is flashing in the instrument panel, move the gear selector to position A then to position N .  If the " Foot on the brake " is displayed, press the brake pedal f i r m l y.
 Place the gear selector at position N .  Insert the electronic key in the reader. or  With Keyless Entry and Starting, simply having the electronic key inside the vehicle is sufficient. or  Insert the remote control key into the ignition switch and turn it towards the dashboard to position 2 (ignition on).
 Press the brake pedal firmly. Make a single short press (about one second) on the " START/STOP " button. or  Turn the remote control key fully towards the dashboard to position 3 (Starting).  Maintain pressure on the brake pedal until the RE ADY lamp comes on, signalling RE ADY lamp comes on, signalling RE ADY
activation of the HYbrid4 system, confirmed by an audible signal.
On activation of the HYbrid4 system, the instrument panel lights up, the power indicator needle is placed at position " 0 ". The steering column automatically unlocks (perceptible noise and movement of the steering column). Depending on certain parameters, such as the state of charge of the high voltage battery or the ambient temperature, the HYbrid4 system itself determines whether it is necessary to
start the HDi Diesel engine. The mode selector is at the AUTO position.

16
Hybrid4 system
508HY-comp_en_Chap00b_hybrid_ed01-2016
Switching the ignition on
Turn the remote control key towards the dashboard to position 2 (ignition on) or, with the electronic key of the Keyless Entry and Starting system inside the vehicle, press the " S TA R T/STOP " button, with no action on the brake pedal to switch on the ignition for temporary use of the vehicle's ancillary equipment.
 Press the " START/STOP " button, the instrument panel comes on but the HYbrid4 system does not start.  Press this button again to switch off the ignition and allow the vehicle to be locked.
With the ignition on, the system automatically changes to economy mode when required to maintain an adequate state of charge of the battery.
For reasons of safety and theft protection, do not leave your electronic key in the
vehicle, even when you are close to it. It is recommended that you keep it on your person.
Switching off the HYbrid4 system
 Immobilise the vehicle.  Place the gear selector in position N .  Make a short press (about one second) on the " START/STOP " button. or  Turn the remote control key fully towards you to position 1 (Stop).
Check that the RE ADY lamp is off RE ADY lamp is off RE ADYbefore leaving the vehicle. Never leave the electronic key inside the vehicle in your absence.
The HYbrid4 stops: - the RE ADY lamp goes off, RE ADY lamp goes off, RE ADY - the steering column locks, - the electric parking brake is applied automatically, unless its automatic mode is deactivated.
 Check that the parking brake warning lamps are on.  Remove the electronic key from the reader. or  Remove the remote control key from the ignition switch.
Before doing anything under the bonnet, the HYbrid4 must be switched off ( RE ADY lamp off) and the electric RE ADY lamp off) and the electric RE ADY
parking brake must be applied.

39
8
In the event of a breakdown
508HY-comp _en_Chap08_en-cas-de-pannes_ed01-2016
Removing / Refi tting the 12 V battery
This procedure allows you to safely remove the 12 V battery, when needed to change a left hand headlamp bulb.
You can contact a PEUGEOT dealer or a qualified workshop to have this done.
Before removing
 Place the vehicle in a ventilated area, with free access and preferably on level ground.  Apply the parking brake.  Place the gear selector in position N .  If the vehicle has an alarm, leave the bonnet open to avoid triggering the alarm.  Leave at least one window open if parking in a secure area, other wise lock all doors and the boot.  If your vehicle has a motorised tailgate, it will not be possible to open it after disconnecting the battery.  Switch of the ignition and remove the key.  If your vehicle has Keyless Entry and Starting, place the remote control at least 3 metres away.  Wait around 6 minutes before disconnecting the battery.
R e m o v i n g
 Disconnect the positive ( + ) terminal of the + ) terminal of the +battery.