2016 NISSAN TITAN engine

ENGINE
ModelCummins 5.0L
Type Diesel, 8-cycle, DOHC
Cylinder arrangement 8-cylinder, V-block, Slanted at 90°
Bore x Stroke in (mm) 3.701 x 3.543 (94 x 90)
Displacement cu in (cm
3) 305.10 (5,000)
Idle speed
No adjustment is necessary.
A/T (in “N” position)
Ignition speed at the N (Neutral) position
(RPM)
Camshaft operation
Timing chain
SPECIFICATIONS
Capacities and Specifications8-7

Due to legal requirements in some states and
Canadian Provinces, your vehicle may be re-
quired to be in what is called the “ready condi-
tion” for an Inspection/Maintenance (I/M) test of
the emission control system.
If a powertrain system component is repaired or
the battery is disconnected, the vehicle may be
reset to a “not ready” condition.
The vehicle is set to the “ready condition” when it
is driven through certain driving patterns. Usually,
the ready condition can be obtained by ordinary
usage of the vehicle.
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (diesel
engine only)
8-8Capacities and Specifications

9 Index
A
AirCleaner ...................6-19
Air cleaner housing filter ............6-19
B
Belt (See drive belt) ..............6-18
C
Capacities and recommended
fuel/lubricants..................6-26
Coolant Capacities and recommended
fuel/lubricants ................6-26
Changing engine coolant ..........6-4
Checking engine coolant level .......6-4
D
Diesel Particulate Filter
(DPF) .........2-3,2-5,2-5,2-6,2-7,6-17
Drive belt ....................6-18
E
Engine Capacities and recommended
fuel/lubricants ................6-26 Changingenginecoolant..........6-4
Changingengineoil.............6-6
Changing engine oil filter
..........6-8
Checking engine coolant level .......6-4
Checking engine oil level ..........6-5
Engine compartment check locations ....6-2
Engine cooling system ............6-3
Engine oil ...................6-5
Engine oil and oil filter recommendation .6-29
Engine oil viscosity .............6-30
Engine specifications ............6-31
Starting the engine ..............3-2
F
Fluid Capacities and recommended
fuel/lubricants ................6-26
Engine coolant ................6-3
Engine oil ...................6-5
Fuel Capacities and recommended
fuel/lubricants ................6-26
Fuel recommendation ...........6-27
Fuel-filler door ..................4-2
J
Jump starting ...................5-2 O
Oil Capacities and recommended
fuel/lubricants ................6-26
Changingengineoil.............6-6
Changing engine oil filter ..........6-8
Checking engine oil level ..........6-5
Engine oil ...................6-5
Engine oil and oil filter
recommendation ..............6-29
Engine oil viscosity .............6-30
R
Readiness for inspection maintenance (I/M)
test ........................6-32
Recommended Fluids .............6-26
Remote Start ...................3-3
S
Specifications ..................6-31
Starting Jump starting .................5-2
Starting the engine ..............3-2
Starting the engine ................3-2

FUEL RECOMMENDATION:
For additional information, refer to “Fuel recom-
mendation” in the “Titan Diesel Owner’s Manual”.
ENGINE OIL RECOMMENDATION:
For additional information, refer to “Engine oil
recommendation” in the “Titan Diesel Owner’s
Manual”.
COLD TIRE PRESSURE:
For additional information, refer to “Tire and load-
ing information label” in the “Technical and con-
sumer information” section of this manual.
The label is typically located on the driver side
center pillar or on the driver’s door. For additional
information, refer to “Wheels and tires” in the
“Maintenance and do-it-yourself” section of this
manual.
RECOMMENDED NEW VEHICLE
BREAK-IN PROCEDURE:
For additional information, refer to the “Engine
break-in recommendations” section in the “Intro-
duction” of the “Titan Diesel Owner’s Manual”
supplement.
GAS STATION INFORMATION