2016 NISSAN NOTE differential

TRANSAXLE ASSEMBLYTM-37
< UNIT DISASSEMBLY AND ASSEMBLY > [5MT: RS5F91R]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
6. Install control shaft (1) to transaxle case, and tighten bolts ( ) to the specified torque.
CAUTION:
Replace control shaft and selector as a set.
7. Install selector to control shaft, and then install retaining pin ( ) to selector, using suitable tool.
CAUTION:
• Be careful with the orientation of selector.
• Replace control shaft and selector as a set.
• Do not reuse retaining pin.
8. Install gear catch, spring, and bushing to transaxle case, and then tighten bolt ( ) to the specified torque.
CAUTION:
Replace gear catch, spring, and bushing as a set.
9. Install oil gutter to transaxle case.
10. Install air breather inner tube (2) to transaxle case. CAUTION:
Do not damage air breather inner tube.
NOTE:
It is easier to install when air breather inner tube end is wrapped
and narrowed by tape. Remove tape after installation.
11. Insert 2-way connector (1) straight, and then install it to air breather inner tube.
CAUTION:
Check air breather inner tube fo r twists after installing.
12. Install differential side oil seals (1) to clutch housing and tran- saxle case, using Tool.
PCIB1540E
SCIA1726J
JPDIC0533ZZ
PCIB1541E
(B) : Transaxle case side
(C) : Clutch housing side
Dimension (L1) : 5.7 – 6.3 mm (0.224 – 0.248 in)
Dimension (L
2): 2.4 – 3.0 mm (0.094 – 0.118 in)
Tool number : KV32500QAA ( — )
JPDIC0401ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-38
< UNIT DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
CAUTION:
• Do not reuse differential side oil seal.
• Do not tilt differential side oil seal.
• Do not damage clutch housing and transaxle case.
13. Install differential side bearing outer races until they reach clutch housing and transaxle case, using Tool (A).
CAUTION:
Replace differential side bearing outer race and differential
side bearing as a set.
14. Install bushings (1) until they reach clutch housing, using suit- able tool (A).
CAUTION:
Do not reuse bushings.
15. Install oil channel to clutch housing. CAUTION:
Do not reuse oil channel.
16. Install mainshaft front bearing so that it becomes even with clutch housing surface, using Tool (A).
17. Install input shaft front bearing so that it becomes even with clutch housing surface, using Tool (A).
18. Install pinion gear, pinion shaft, and plug to clutch housing. Tool number : KV32300QAE ( — )
PCIB1549E
JPDIC0637ZZ
Tool number : ST33400001 ( — )
PCIB1544E
Tool number : KV40100900 ( — )
PCIB1545E
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-52
< UNIT DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
FINAL DRIVE
FINAL DRIVE
Exploded ViewINFOID:0000000012430976
DisassemblyINFOID:0000000012430977
• Remove differential side bearings, using Tool (A) and suitable tool.
AssemblyINFOID:0000000012430978
• Install differential side bearings, using Tool (A).
CAUTION:
Replace differential side bearing outer race and differential
side bearing as a set.
InspectionINFOID:0000000012430979
INSPECTION AFTER DISASSEMBLY
Gear and Final Drive
1. Differential side bearing outer race 2. Differential side bearing 3. Final drive
: Replace the parts as a set.
JPDIC0481ZZ
Tool number : ST33052000 ( — )
PCIB1568E
Tool number : KV40104920 ( — )
PCIB1570E
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-60
< PREPARATION >[CVT: RE0F11A]
PREPARATION
Drift
a: 53 mm (2.09 in) dia.
b: 50 mm (1.97 in) dia. Installing differential side oil seal
Drift
a: 60 mm (2.36 in) dia.
b: 55 mm (2.17 in) dia. Installing converter housing oil
seal
Tool number
Tool name
Description
NT115
NT115
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-70
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
STRUCTURE AND OPERATION
STRUCTURE AND OPERATION
TRANSAXLE
TRANSAXLE : Cross-Sectional ViewINFOID:0000000012431010
TRANSAXLE : Trans
axle MechanismINFOID:0000000012431011
BELT & PULLEY
1. Converter housing 2. Oil pump3. Counter drive gear
4. Control valve 5. Oil pan6. Primary pulley
7. Steel belt 8. Secondary pulley9. Planetary gear (auxiliary gearbox)
10. Side cover 11. Transaxle case12. Differential case
13. Final gear 14. Reduction gear15. Counter driven gear
16. Drive sprocket 17. Oil pump chain 18. Torque converter
19. Driven sprocket
JSDIA1777ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CVT CONTROL SYSTEMTM-225
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom diagnosis chart 1-2
Symptom Replace the transaxle assembly.
Oil pres-
sure con- trol Power transmission
Valve body, control valve
Oil pump
Torque converter
Pulley, steel belt
Low brake
High clutch
Reverse brake
Bearings
Counter gear
Planetary gear
Reduction gear
Final gear, differential gear
Parking mechanism
TM-259
Driving is
not possi- ble. The engine speed increases in
“D”, “L”, or “R” position, but the
vehicle cannot start.
11 11
(In “D” or “L”) 1
(In “R”) 1111
Engine stall occurs in “D”, “L”,
or “R” position and the vehicle
does not start. 1
111111
Acceleration at start is not suf-
ficient in “D”, “L”, or “R” posi-
tion. 111
(In “D” or “L”) 1
(In “R”)
The engine speed increases
suddenly in “D”, “L”, or “R” po-
sition during driving. 11 11
(In “D” or “L”) 1
(In “D” or “L”) 1
(In “R”)
Engine brake is suddenly ap-
plied in “D” or “R” position dur-
ing driving. 1
1
(In “D” or
“L”) 1
(In “D” or
“L”) 1
(In “R”)
Shifting is
not possi- ble. The engine races when the
auxiliary gearbox is shifted
from 1GR ⇔
2GR. 11 2 1 1
Engine braking is not effective
in “L” position. 1212 1 1
Shifting does not occur with
OD OFF.
Engine stall occurs immedi-
ately before stop at decelera-
tion in “D” or “L” position. 11
During driving in “D” position,
slippage occurs in lockup or
lockup is not possible. 11
Revision: August 2015
2016 Versa Note

cardiagn.com

CVT CONTROL SYSTEMTM-227
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom diagnosis chart 2-2
Symptom Replace the transaxle assembly.
Oil pres-
sure con- trol Power transmission
Valve body, control valve
Oil pump
Torque converter
Pulley, steel belt
Low brake
High clutch
Reverse brake
Bearings
Counter gear
Planetary gear
Reduction gear
Final gear, differential gear
Parking mechanism
TM-259
Shock vi-
bration
Noise Shock at start is large in “D”,
“L”, or “R” position.
111
(In “D” or “L”) 1
(In “R”) 2222
Shock is large when the auxil-
iary gearbox is shifted from
1GR → 2GR. 11
1
Shock in lockup is large dur-
ing driving in “D” or “L” posi-
tion. 11
Shock is large when the lever
is shifted from “N” → “D” and
“N” → “R” positions. 11
(“N” →
“D”) 1
(“N” →
“D”)
Shock is large when the lever
is shifted from “D” → “L” posi-
tion. 11
1
Vibration occurs in “D”, “L”, or
“R” position during driving. 11111
(In “D” or “L”) 1
(In “D” or “L”) 1
(In “R”) 11111
Noise occurs during driving. 1 1 1 11111
Noise occurs in idling. 1 1 1 1 1 1
Other Starter operates in “D”, “L”, or
“R” position.
Starter does not operate in “P”
or “N” position.
Engine stall occurs
in “D”, “L”,
or “R” position during stop. 11
Engine stall occurs in “P” or
“N” position during stop.
Parking lock does not operate
in “P” position. 1
Parking lock cannot be can-
celled when the selector lever
is shifted from “P” position to
other position. 1
Revision: August 2015
2016 Versa Note

cardiagn.com

DIFFERENTIAL SIDE OIL SEALTM-249
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
DIFFERENTIAL SIDE OIL SEAL
Exploded ViewINFOID:0000000012431204
Removal and InstallationINFOID:0000000012431205
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the front drive shaft from the transaxle assembly. Refer to FAX-19, "Removal and Installation"
2. Remove the differential side oil seal using suitable tool.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mating surfaces
of the transaxle case and converter housing.
INSTALLATION
CAUTION:
When inserting the drive shaf t, be sure to use Tool.
1. Measure height (A) of seal lip. Calculate protrusion (C) of seal
lip according to measured height (A) of seal lip and reference
value (B) of side oil seal insertion.
CAUTION:
• Do not reuse differential side oil seal.
• Put a mark on the measurement area and measure height of seal lip at four points diagonally
using suitable tool.
NOTICE:
1. Transaxle assembly 2. Differential side oil seal (left side) 3. Differential side oil seal (right side)
Front Genuine NISSAN CVT Fluid NS-3
JSDIA1888ZZ
Tool number : KV38107900 ( — )
(1) : Differential side oil seal
(2) : Converter housing or transaxle case
Lip protrusion (C): C=A–B
Differential side oil seal insertion
reference value (B) : 1.8 mm (0.071 in)
JSDIA4816ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com