2016 NISSAN NOTE key

BCS-114
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
1: With variable intermittent wipers
2: Without variable intermittent wipers60
(BG) Ground Door sw (AS) signal Input Front door
switch RHOFF (front door RH
closed)
7.0 - 8.0 V
ON (front door RH open) 0 V
62
(P) Ground Door switch (Back)
signal InputBack door
switch OFF (back door closed)
7.0 - 8.0 V
ON (back door open) 0 V
63
(W) Ground Flasher output
(RIGHT) signal
OutputIgnition switch
ON Turn signal switch OFF
0 V
Turn signal switch RH 6.5 V
(Turn signal lamp turn on: 9 - 16
V)
64
(V) Ground
Flasher output
(LEFT) signal Output
Ignition switch
ON Turn signal switch OFF
0 V
Turn signal switch LH 6.5 V
(Turn signal lamp turn on: 9 - 16 V)
68
(R) Ground Rear wiper motor
output 1
OutputPush-button ig-
nition switch ON Rear wiper stop position
Battery voltage
Any position other than
rear wiper stop position 0V
70
(L) Ground
Cargo lamp output
signal Output Back door Closed (cargo lamp OFF)
Battery voltage
Open (cargo lamp ON) 0 – 1 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4960J
PKIB4960J
PKIC6370E
PKIC6370E
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-115
< ECU DIAGNOSIS INFORMATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
Fail-safeINFOID:0000000012432390
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
FAIL-SAFE CONTROL OF COMBINATION SWIT
CH READING FUNCTION CAUSED BY LOW
POWER SUPPLY VOLTAGE
If voltage of battery power supply lower, BCM maintains combination switch reading to the status when input
voltage is less than approximately 9 V.
NOTE:
When voltage of battery power supply is approximately 9 V or more, combination switch reading function
returns to normal operation.
DTC Inspection Priority ChartINFOID:0000000012432391
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC IndexINFOID:0000000012432392
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- tion switch OFF → ON again.
• 1 - 39: Displayed if any previous ma lfunction is present when current conditi on is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condi tion if the malfunction is detected again.
Display contents of CONSULT Fail-safe Cancellation
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2196: DONGLE NG Inhibit engine cranking Erase DTC
Priority DTC
1 • U1000: CAN COMM
• U1010: CONTROL UNIT (CAN)
2 • B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2196: DONGLE NG
3 • C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESS DATA ERR] FL
• C1717: [PRESS DATA ERR] FR
• C1718: [PRESS DATA ERR] RR
• C1719: [PRESS DATA ERR] RL
• C1729: VHCL SPEED SIG ERR
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS-116
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
CONSULT display
Fail-safeTire pressure monitor
warning lamp ON Reference
U1000: CAN COMM ——BCS-127
U1010: CONTROL UNIT (CAN) ——BCS-128
B2190: NATS ANTENNA AMP ×—SEC-144
B2191: DIFFERENCE OF KEY ×—SEC-147
B2192: ID DISCORD BCM-ECM ×—SEC-148
B2193: CHAIN OF BCM-ECM ×—SEC-150
B2195: ANTI SCANNING ×—SEC-151
B2196: DONGLE NG ×—SEC-152
C1704: LOW PRESSURE FL —×
WT-25
C1705: LOW PRESSURE FR —×
C1706: LOW PRESSURE RR —×
C1707: LOW PRESSURE RL —×
C1708: [NO DATA] FL —×
WT-27
C1709: [NO DATA] FR —×
C1710: [NO DATA] RR —×
C1711: [NO DATA] RL —×
C1716: [PRESS DATA ERR] FL —×
WT-30
C1717: [PRESS DATA ERR] FR —×
C1718: [PRESS DATA ERR] RR —×
C1719: [PRESS DATA ERR] RL —×
C1729: VHCL SPEED SIG ERR —×WT-32
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-117
< WIRING DIAGRAM > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
WIRING DIAGRAM
BCM
Wiring DiagramINFOID:0000000012432393
ABMWA3494GB
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS-118
< WIRING DIAGRAM >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
AAMWA1406GB
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
BCM
BCS-119
< WIRING DIAGRAM > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
ABMIA7844GB
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS-120
< WIRING DIAGRAM >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
ABMIA7845GB
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
ADDITIONAL SERVICE WHEN REPLACING BCMBCS-121
< BASIC INSPECTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING BCM
DescriptionINFOID:0000000012432394
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle s
pecification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function do es not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm conf iguration of each vehicle model.
• If you set incorrect “WRITE CONF IGURATION”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NATS) (if equipped).
Work ProcedureINFOID:0000000012432395
1.SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or prin t current vehicle specification. Refer to BCS-123, "
Descrip-
tion".
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
>> GO TO 2.
2.REPLACE BCM
Replace BCM. Refer to BCS-137, "
Removal and Installation".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “W RITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to BCS-123, "
Work Procedure".
>> GO TO 4 (with remote keyless entry system).
>> GO TO 6 (without remote keyless entry system).
4.REGISTER IGNITION KEYS
For initialization and registration of ignition keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
>> GO TO 5.
5.REGISTER KEYFOB ID
For registration of keyfob ID, refer to DLK-257, "
ID Code Entry Procedure".
>> Work End.
Revision: August 2015 2016 Versa Note

cardiagn.com