2016 NISSAN MURANO HYBRID tire pressure

TIRE PRESSURE MONITORING SYSTEM
ALERT
Refer to your vehicle Owner’s Manual for more informa-
tion on what to do if the tire pressure warning system
activates.
WARNING
If the tire pressure-monitoring system signals an alert,
follow these safety precautions to prevent a loss of
vehicle control that could result in serious personal
injury or death:
●Slow your speed. Do not exceed 50 mph (80 kph) .
●Avoid hard cornering, hard braking and severe han-
dling maneuvers.
●Avoid potholes and other road hazards.
Remember that when your tires have lost air pressure,
your vehicle’s handling capability is reduced, particu-
larly during severe maneuvers.
TO PROLONG TIRE LIFE DURING A
SYSTEM ALERT
The Goodyear or Dunlop Run-Flat tire can be driven at
low or zero air pressure (refer to your vehicle Owner’s
Manual for these limitations) . To help prolong the life of
a tire operating under low-inflation conditions, drive at a
speed as far below 50 mph (80 kph) as possible. Also,
drive the shortest distance possible before obtaining
tire service. Taking these precautions will increase the
chance that your tire will be repairable.
SERVICE AFTER A SYSTEM ALERT
To obtain service after operating under low-inflation
conditions, contact your Goodyear or Dunlop Run-Flat
service facility. Trained service personnel will inspect
your tires to determine if they are in need of repair or
replacement. To locate the nearest authorized Good-
year or Dunlop Run-Flat service facility, call 1-800-
GOODYEAR (1-800-466-3932) .
WARNING
Because of the unique characteristics of Run-Flat tires,
the wheels on which they are mounted and your vehi-
cle’s tire pressure monitoring system, all tire service
work other than routine inflation maintenance and exter-
nal inspections must be performed by service personnel
at a Goodyear or Dunlop Run-Flat service facility. Do not
attempt to mount or demount Run-Flat tires yourself;
serious injury or death could result. Only specially
trained persons should mount, demount and repair Run-
Flat tires, and more than 40 psi (270 kPa) may be
required to seat beads. A safety cage and clip-on ex-
tension air hose must be used if more than 40 psi
(270kPa) is needed to seat beads.
TIRE REPAIR
Like any other Goodyear or Dunlop speed-rated, high-
performance tire, the Goodyear or Dunlop Run-Flat tire
may be repaired to correct a puncture in the tread, but
PROPER MATERIALS AND PROCEDURES MUST BE
USED. Contact a Goodyear or Dunlop Run-Flat service
facility for information on proper repairs. For the location
of the nearest facility, call 1-800-GOODYEAR (1-800-
466-3932) . WARNING
Goodyear and Dunlop Run-Flat tires are designed for
use only on certain original equipment wheels s upplied
with a properly operating low tire pressure-monitoring
system. If applied to a vehicle without a properly oper-
ating low tire pressure-monitoring system, the tires may
fail when operated in an underinflated condition, result-
ing in loss of vehicle control and possible serious injury
or death. Application of these tires to a vehicle not
equipped with specified operational low tire pressure-
monitoring system constitutes improper and unsafe use
of this product.
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
31

5. COMPANY’S OBLIGATIONS
Any replacement qualifying under this Adjustment
Policy will be made by any Continental/General brand
authorized dealer or vehicle dealer authorized to handle
Continental or General brand tire adjustments. Com-
pany will replace the tire pursuant to the terms of this
Adjustment Policy.
6. OWNER’S OBLIGATIONS
To make a claim under this Policy concerning any tire
which is covered by this Policy, you must present your
claim with the tire to any Continental or General brand
tire dealer or vehicle dealer authorized to handle Conti-
nental or General brand tires. For the nearest Continen-
tal or General brand tire dealer, check the Yellow Pages,
or use the Continental or General brand Internet ad-
dress, or one of the “800” numbers shown under “For
Customer Assistance.” To be eligible for the terms of
this Policy, you need to present your new vehicle regis-
tration form or new vehicle sales invoice showing date
of purchase. Tires replaced on an adjustment basis
become the property of Company. You will be required
to sign the Company Limited Warranty Claim Form or
dealer replacement sales receipt.
You are responsible for payment of all applicable taxes
demounting, mounting and balancing charges set forth
under this Policy. You are also responsible for payment
of local tire-disposal fees and any parts or service
regardless of mileage or months of service. This in-
cludes payment for tire rotation, alignment, towing, road
service, valve stems and tire repairs.
Owner is responsible for maintaining proper tire air
pressure and for proper maintenance of the tire.
THE WARRANTOR
The warrantor of Continental and General brand tires is
Continental Tire North America, Inc., 1830 McMillan
Park Drive, Fort Mill, SC 29707.
For Customer Assistance:
1-800-847-3349 (Nationwide)
1-800-461-1776 (In Canada)
http://www.generaltire.com
http://www.continentaltire.com
SAFETY WARNING
Disregarding any of the safety precautions and in-
structions contained in the Owner’s Manual or the
Important Tire Safety Information in this booklet may
result in tire failure or explosion causing serious
personal injury or death.
34CONTINENTAL/GENERAL TIRE LIMITED WARRANTY

LIMITED WARRANTY
This limited warranty applies to Falken brand Original
Equipment Passenger Car, Temporary Spare, and Light
Truck steel belted radial tires bearing the complete
description and serial number required by the Depart-
ment of Transportation (DOT) . This warranty is effective
only to tires for which claims are made within 5 (five)
years of the date of production, based on the tire DOT
serial number.
WHAT IS COVERED AND FOR HOW
LONG
Falken tires that are originally equipped on this vehicle
are warranted against any defects in the materials and
workmanship for the usable life of the original tread. The
limited warranty terminates at the flush appearance of
the tread wear indicators at 1.6mm (2/32 of an inch)
remaining tread depth.
A.Free Replacement
If a tire becomes unserviceable due to such defect
within the first 1.6mm (2/32 of an inch) of tread wear,
the tire will be replaced free of charge with the same or
comparable Falken tire.
B. Prorated Replacement
After the first 1.6mm (2/32 of an inch) of wear, a
prorated adjustment credit will be given based on the
percentage of remaining usable tread depth, down to
the remaining 1.6mm (2/32 of an inch) tread wear bar
indicator. No credit is given if the tire is worn beyond the
flush appearance of the tread wear bar indicator (less
than 1.6mm (2/32 of an inch) tread depth remaining) . C.
Out-of-Round / Out-of-Balance Replacement
Tires that are deemed to be out-of-round or out-of-
balance will be accepted for adjustment during the first
0.8mm (1/32 of an inch) of the original tread depth and
will be replaced free of charge with the same or similar
Falken tires (no labor costs will be covered) . A set of
four (4) tires from the same vehicle will not be accepted
for out-of-round or out-of-balance claims.
WHAT IS NOT COVERED BY THE
WARRANTY
A. Tires that becomes unserviceable due to road haz- ard damages (cuts, snags, punctures, bruises, im-
pact breaks, etc.) improper repair technique or ma-
terials, improper inflation, overload, irregular wear,
wheel imbalance, defective mechanical vehicle
components (brakes, suspension, wheels, etc.) im-
proper suspension alignment, accident, fire, chemi-
cal damage, damage from chain use, racing, off-
road use, run flat, improper installation, vandalism, or
abuse.
B. Tires branded “NA” or a tire in which the DOT numbering has been removed.
C. Tires presented for a warranty claim by someone other than by the original purchaser, or tires that
were transferred to another vehicle from the vehicle
in which the tires were originally installed.
D. Tires having a failure or failures caused by a previous damages or repairs.
E. The cost of tire repair or retreading is not covered by this warranty and will be the sole responsibility of the
tire owner. Possible NON Covered Reasons/Conditions due
to:
●Chipping/Chunking Tearing
●Corrosion
●Fire
●Impact Break or Concussions
●Improper Inflation Pressure
●Improper Mounting/Dismount
●Mechanical Defects of the Vehicle
●Misalignment
●Misapplication
●Overloading
●Puncture
●Racing or any Competition
●Repair Failure
●Road Hazards
●Sidewall Cut or Damage
●Theft or Vandalism
●Tread Cuts
●Wheel Imbalance
●Willful Abuse
(Continued on next page)
FALKEN TIRE LIMITED WARRANTY
35

OWNER’S OBLIGATIONS
At least monthly, the vehicle owner(s) should check the
tires’ air pressure with a gauge and inflate to the recom-
mended cold air pressure level listed on the driver’s
door placard. Do not rely on car servicers to perform the
checks. The tires should be rotated at least every
8,000km (5,000 miles) or earlier if uneven wear is
occurring, and proof of maintenance records should be
kept. The owner(s) should have the tires rebalanced if
vibration is experienced, and the vehicle’s alignment
should be checked if uneven or rapid wear is occurring,
or when suggested by the vehicle’s manufacturer.
All warranty claims must be presented to an authorized
Falken dealer or participating car dealership. The own-
er(s) must present any supporting maintenance records
and documentation necessary to help determine if the
tire(s) in question are deemed covered by the limited
warranty or not.
LEGAL RIGHTS
All implied warranties, including warranties of mer-
chantability and fitness for a particular purpose shall be
limited in duration to the above period. To the extent
permitted by law, Falken Tire Corporation shall not be
responsible for incidental or consequential damages,
such as loss of use of the tire or the vehicle on which it
is used, inconvenience, or commercial loss, some states
do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of incidental or con-
sequential damages, so the above limitations or exclu-sions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights,
which vary from state to state. This is the only express
warranty applicable to Falken brand tires and super-
sedes the terms of any previous warranty. Falken neither
assumes nor authorizes anyone to make or assume for it
any other warranty.
TIRE CARE AND RECOMMENDATIONS
PROPER INFLATION and FUEL ECONOMY*
Ensure maximum performance and a long life from your
tires by checking the air pressures at least once a month
and set them to the vehicle manufacturer’s recom-
mended pressure(s) listed on the vehicle’s tire placard
or in your owner’s manual. Always check and adjust your
air pressure when your tires are cold, preferably first
thing in the morning before driving. Never release air
pressure from tires when they are hot. Wait until the tires
cool down and recheck, adding air or releasing as
required. Falken endorses the use of nitrogen in your
tires because it helps your tires maintain optimal pres-
sure for longer periods of time and reduces the amount
of moisture inside of the tire and wheel assembly.
TIRE INFLATION PRESSURE
Tires need to be properly inflated to effectively operate
and perform as intended. Tires carry the weight of the
vehicle, passengers, and cargo as well as bear the
forces of braking, accelerating, and turning. The vehicle
manufacturer sets the inflation pressures for the original
equipment tires that are on your vehicle.Driving with improperly inflated tires is dangerous. An
under inflated tire will generate excessive heat build-up
that will cause damage to the internal structure and
inner liner of the tire. Besides tire damage, improper tire
inflation pressures can also affect your vehicle’s ride
and handling, tire tread wear, and fuel economy. It is
recommended to always keep all of your tires, including
the spare, at the vehicle manufacturer’s recommended
inflation pressures and be sure to check the air pressure
monthly and before going on long road trips or carrying
extra weight in your vehicle.
Your vehicle’s tire placard and/or owner’s manual will
list the cold inflation pressure(s) for your vehicle’s origi-
nal equipment tires, including the spare. The placard
can be found on the driver’s side door or door jamb area.
If you have questions about understanding your vehi-
cle’s tire placard, please refer to your owner’s manual or
ask a qualified tire service professional.
●For detailed information on TIRE INFLATION PRES-
SURE please visit www.Falkentire.com
CHECKING YOUR TIRE’S AIR PRESSURE
Checking your air pressure at least once a month is vital
to help your tires perform properly and help you get the
best gas mileage possible. Tires can lose up to 7 kPa
(1 psi) per month under normal conditions and lose up
to 7 kPa (1 psi) per every 9°C (16°F) drop in tempera-
ture. Here are some simple steps on how to check the
air pressures in your tires: 1. Remove the valve stem cap.
(Continued on next page)
* Some plus size applications may require different air pressure(s) than what is listed on your vehicle’s placard or owner’s manual. In this case, please consult your tire dealer or Falken Tire for proper inflation pressure(s) .
36 FALKEN TIRE LIMITED WARRANTY

2. Place the end of the tire gauge firmly against thetire’s valve stem.
3. Read the current pressure displayed on the gauge that is currently in the tire.
4. Increase pressure at this time (if needed) and re- check with your tire gauge.
5. Replace the valve stem cap.
6. Repeat until all of your tires have been checked and adjusted accordingly.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
A tire pressure monitoring system (TPMS) is a safety
system found in most vehicles manufactured after
2005. There are pressure sensing transmitters mounted
inside of each tire that sends readings to the central
computer (ECU) in your vehicle. The TPMS system will
alert you when one or more of your tires are underin-
flated by 25% or more by turning on a warning light on
your vehicle’s dashboard or heads up display (HUD)
screen. This means that one or more of your tires may
have a low-pressure condition. Follow the instructions
in your owner’s manual.
ROTATION and WEAR
**
Falken recommends rotating your tires at least every
8,000km (5,000 miles) and periodically inspecting your
tires to make sure they are free of road hazards (such as
nails, screws, large wood splinters, etc.) that might
penetrate your tires causing them to lose air pressure
and to ensure they are wearing evenly. Common irregu-
lar wear patterns are: misalignment wear, where the tire
shows excessive outer or inner tread wear. Tire side- walls should also be inspected for cuts, snags, bruises,
and weather cracking. If any of these noted conditions
are present during inspection, we recommend returning
to your servicing tire dealer to be corrected to ensure
long tire life.
TIRE REPLACEMENT
Falken recommends replacing your tires when the tread
wears down to the wear bars at 1.6mm (2/32 of an
inch) , which are located across the tread in several
locations around the tire. If only two tires are being
replaced, the two new tires should always be installed
on the rear of the vehicle to aid in preventing your
vehicle from hydroplaning, even if your car is front wheel
drive. It’s always recommended to have your new tires
balanced during installation, and alignment checked if
the previous tires show and irregular wear. Tires that
have been in use for 5 (five) years or more should
continue to be inspected by a qualified tire specialist, at
least annually. It is recommended that any tires 10 (ten)
years old or older from the date of manufacture, includ-
ing spare tires, be replaced with new tires as a precau-
tion even if such tires appear serviceable and even if
they have not reached the legal worn out limit at 1.6mm
(2/32 of an inch) .
TIRE REPAIRS
In the event that you get a flat tire while driving, it is best
to find a nearby, safe place to stop and install your spare
tire or call a tow truck. The less distance that you drive
on your low or flat tire, the better chances your tire has of
being repairable. Once you are able to get to your local
servicing tire dealer, have them dismount the tire fromthe rim and thoroughly inspect the inside of the tire. It is
important to know the difference between a proper tire
repair and an improper one because it can be critical to
you and your vehicle’s safety. An improper repair could
pose a safety threat to you and your family and could
also affect your tire’s manufacturer warranty. Here are
some tips in determining if your damaged tire can be
properly repaired or not:
●Always have the tire removed from the wheel and
inspected before any repair is performed.
●Tires with less than 1.6mm (2/32 of an inch) of tread
should NOT be repaired.
●Never repair a tire with a puncture larger than 6mm
(1/4 of an inch) .
●Repairs should be limited to the tread area only.
●Repairs cannot overlap one another.
●A plug and patch or plug/patch combo should be
used to effectively repair a tire puncture.
●If anything seems questionable at any time during the
repair process, ask your service advisor for more
details and/or call the tire manufacturer to make sure
the tire’s warranty isn’t being voided.
(Continued on next page)
** Never include a temporary spare tire in your rotation pattern
FALKEN TIRE LIMITED WARRANTY 37

TIRE SPINNING
WARNINGSAFETY WARNING
Spinning a tire to get a stuck vehicle out of
mud, ice, snow, sand, or wet grass can be
potentially dangerous. A spinning tire at a
speedometer reading above 55 km/h
(35 mph) can be capable of disintegrating
a tire with explosive force. In some circum-
stances, a tire may be spinning at twice
the speed displayed on the speedometer.
This can cause serious injury or death to
you, a passenger, or bystander. Never spin
a tire above 55 km/h (35 mph) .
UNDERSTANDING YOUR TIRES
TIRE SPEED SYMBOLS
Tires that are speed-rated are identified by the following
letter symbols: Q, S, T, U, H, V, W, Y, (Y) , or (ZR) . The
Speed Rating’s Symbol can be found as a part of the tire
size designation (ex: 215/65HR16) or after the load
index immediately following the tire size designation (ex:
215/65R16 97H) . The Speed Rating’s Symbol indi-
cates the maximum speed that a tire can handle when
properly inflated and loaded.
●For detailed information on UNDERSTANDING
YOUR TIRES please visit www.Falkentire.com DATE OF TIRE MANUFACTURE
The date that a tire was manufactured can be deter-
mined by examining the last 4 digits of the 12 digit DOT
serial code, which is found on at least one sidewall of a
tire. For tires that were produced after the year 2000,
the last 4 digits of the serial code will identify the week
and the year that the tire was manufactured. If the last 4
digits in the DOT serial code were to read “3013” it
would mean that the tire was manufactured the 30th
week of 2013. If you are uncertain, check with a quali-
fied tire service professional to be sure.
DOT Symbol and DOT Serial Code
The “DOT” symbol claims that the tire conforms to all
applicable US Department of Transportation motor ve-
hicle safety standards for tires. The identification/serial
number follows the “DOT” symbol. Here is an example
of a DOT serial code:
DOT R8 ER DMNR 30 13
(A) (B) (C) (D) (E) (F)
A. DOT Symbol
B. Manufacturer Plant Code
C. Tire Size Code
D. Tire Manufacturer’s Code
E. Week of Production (01–52)
F. Year of Production (the last two digits of the year)
TIRE SIDEWALL LABELING
●For detailed information on TIRE SIDEWALL LABEL-
ING please visit www.Falkentire.com MAX LOAD AND INFLATION
The maximum load and inflation pressure is marked on
the tire sidewall in English and metric units.
PLY COMPOSITION AND MATERIALS
The number of plies and their generic composition of
cord materials in the sidewall and tread areas can be
found on at least one sidewall of a tire.
RADIAL MARKING
A radial ply tire will have the word “radial” marked on at
least one sidewall. An “R” found in the tire size marking
also refers to the tire being a radial ply tire.
UNIFORM TIRE QUALITY GRADING SYSTEM
(UTQG)
The Uniform Tire Quality Grading Standards (UTQG)
were created to help you make an informed decision
when purchasing passenger car tires by providing rela-
tive information about a tire’s tread wear, traction, and
temperature characteristics. Here is a breakdown of the
different categories that the UTQG grades:
●TREAD WEAR
The tread wear grade is a comparative rating based on
the wear rate of the tire when tested under controlled
conditions on a specified government test course. For
example, a tire graded 150would wear one and a half
(1 1/2) times as well on the government course as a tire
graded 100. The relative performance of tires depends
upon the actual conditions of their use, however, and
may depart significantly from the norm due to variations
in driving habits, service practices, and differences in
road characteristics and climate.
(Continued on next page)
FALKEN TIRE LIMITED WARRANTY 39

H. Tire with weather cracking which was purchasedmore than four years prior to presentation for adjust-
ment.
●GENERAL EXCLUSIONS
I. No Hankook Tire employee, retailer or dealer has the authority to make any warranty, representation, prom-
ise or agreement on behalf of Hankook Tire except as
stated in this policy.
J. Tires used in racing related activities or competitive events are not covered by this warranty.
K. Limitation of remedy: to the extent permitted by law, HANKOOK disclaims liability for all consequential
and incidental damages. Some provinces and states
do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation
or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also
have the rights which vary from province to province
in Canada, and from state to state in the U.S.A.
3. HANKOOK’S OBLIGATIONS
Replacement qualifying under this warranty will be
made by a participating Hankook Dealer or a participat-
ing Car Dealer.
4. OWNER’S OBLIGATIONS
A. You must present the tire to a participating Hankook Dealer or a participating Car Dealer.
B. For free replacement, a proof of purchase date such as car dealer invoice should be presented.
C. No claim will be recognized unless submitted on a Hankook claim form completely filled out and signed
by the owner or a participating Hankook Dealer or
Car Dealer.
WARNING FOR YOUR SAFETY
●TIRE DEMOUNTING AND MOUNTING
Improper tire mounting and inflation procedures may
cause tire beads to break with explosive force during
installation of the tire on the rim, causing personal
injury and property damage. Follow the Rubber
Manufacturers Association installation and safety
procedure for mounting and inflating tires. Tire and
rim must match in size. Rim parts must match by
manufacturer’s design. Clean rim. Lubricate rim and
beads. Do not exceed the maximum recommended
pressure to seat beads on rim. Use remote control
inflation equipment and inflation cage.
NOTE:
Never inflate over 40 psi to seat beads. Mount
radial ply tires only on rims designated by wheel
manufacturer as suitable for radial tire. Only spe-
cially trained persons shall mount tires.
●AIR PRESSURE
Check the pressure in your tires, including your
spare, at least monthly, and always before and during
extended driving. Check tires cold (at least 3 hours
after the vehicle has been stopped and before it is
driven more than 1.6 kilometers or 1 mile) . Do not
reduce pressure when tires are hot, use an accurate
air pressure gauge to check pressure and maintain it
at the level recommended on the vehicle tire placard
or in the Owner’s Manual. Underinflation produces
extreme flexing of sidewalls and builds up heat to the
point that premature tire failure may occur. Overin-
flation can cause the tires to be more susceptible to
impact damage. Cold tire pressures, however,
should never be higher than the limit molded on the
sidewall.
●LOAD LIMITS
Never exceed the load-carrying limits molded onto
the sidewall of your tires or the maximum vehicle load
limit as shown on the vehicle tire placard, whichever
is less. Overloading builds up excessive heat in the
tire and leads to early and/or sudden failure.
●HAZARDS
Avoid running over objects (e.g., chuckholes, rocks,
curbs, metal, glass, etc.) which may possibly cause
internal tire damage. Continued use of a tire that has
suffered internal damage (which may not be exter-
nally visible) can lead to dangerous tire failure. De-
termination of suspected internal damage requires
demounting the tire from its rim and examination by
trained tire personnel.
(Continued on next page)
42 HANKOOK TIRE LIMITED WARRANTY

●WORN TIRES
Never drive on worn tires. Tires should be replaced
by trained personnel when 2/32nds inch (1.6mm) of
tread depth remain, as indicated by treadwear indi-
cators molded into the tread grooves. Use of worn-
out tires (less than 2/32nds of an inch remaining
tread depth) increases the probability of tire failure.
In most states, it is illegal to drive with less than
2/32nds of an inch of remaining tread depth.
●SPEED LIMITS
Operating your vehicle in excess of lawful speed
limits or the maximum speeds justified by driving
conditions can be dangerous. Excessive speed cre-
ates heat buildup in a tire, leading to possible tire
failure.
●SPEED-RATED TIRES
Speed-rated tires are identified by letters S, T, H, V,
W, or Z as either part of the size designation (e.g.,
HR) , or part of the service description adjacent to the
size designation (e.g., 94H) and indicates the maxi-
mum speed capability of the tire when properly
loaded and inflated. However, even when properly
loaded and inflated, driving for prolonged periods at
high speeds can cause tire damage and possible tire
failure which could lead to an accident. Original
equipment speed-rated tires must be replaced with
tires of the same or higher speed rating if the speed
capability of the vehicle is to be maintained. Consult
your Hankook dealer for the tires best suited to your
vehicle driving habit. Repairing of speed-rated tires
must be done in accordance with RMA repair pro-
cedures and is limited to one 1/4 diameter repair in
the tread area.
●TIRE ROTATION
Rotate your tires for longer tire life. Front and rear
tires perform different jobs and can wear differently.
Consult your vehicle Owner’s Manual for mileage
recommendations and rotation patterns.
●ADDITIONAL SAFETY INFORMATION FOR TEM-
PORARY TIRE
A. Air pressure. Check inflation pressure as soon as practical after
installation and inflate to 60 psi. The tire pressure
should be checked monthly and maintained at
60 psi while the tire is stored or in service.
B. Vehicle restriction. The temporary spare tire was specifically designed
for your car and should not be used on any other
vehicle.
C. Other restrictions. The temporary spare tire should not be used with
other wheels, nor should standard tires, snow tires,
wheel covers, or trim rings be used with the tempo-
rary spare wheel. If such use is attempted, damage
to these items or other vehicle components may
occur.
TIRE SERVICE ASSISTANCE OR
INFORMATION
When you have tire problems, Hankook provides ser-
vice and assistance.
Any time you see damage to your tires, contact your
local Hankook Tire Dealer.
If no local dealer is available around you, dial Hankook
Toll Free Service Number so that you can get informa-
tion on where and how service is rendered to you. FOR SERVICE ASSISTANCE OR INFORMATION
U.S.A.
CORPORATE HEADQUARTERS
1450 Valley Road, Wayne, New Jersey 07470
973-633-9000 Toll Free 877-740-7000
WEST REGIONAL OFFICE
11555 Arrow Route, Suite 105, Rancho Cucamonga,
CA 91730
909-481-9800 Toll Free 800-426-8252
CANADA
CORPORATE HEADQUARTERS
30 Resolution Dr., Brampton, Ontario L6W 0A3
905-463-9802 Toll Free 800-843-7709
HANKOOK TIRE LIMITED WARRANTY
43