2016 NISSAN JUKE lights


> (GLW    0RGHO )' @
If the moonroof does not operateGUID-375D2428-A2C2-47EB-BFE4-FA7A4BDC9925If the moonroof does not operate properly,
perform the following procedure to initialize the
moonroof operation system.
1. If the moonroof is open, close it fully byrepeatedly pushing the switch toward
*2.
2. Push and hold the switch toward
*2to
tilt the moonroof up.
3. Release the moonroof switch after the
moonroof moves slightly up and down.
4. Push and hold the switch toward
*1to
fully tilt the moonroof down.
5. Check if the moonroof switch operates
normally.
If the moonroof does not operate properly after
performing the procedure above, have your
vehicle checked by a NISSAN dealer.
GUID-AC8C958B-C3DE-4C13-A406-ED56FDB6824E
CAUTION
Do not use for extended periods of time
with the engine stopped. This could
result in a discharged battery.
SIC4572
MAP LIGHTS (if so equipped)GUID-1B5DECC4-5E3F-4B04-8666-6F7000099558Operate the map light switch to turn the map
light on or off.
*1: ON position
*2: OFF position
Instruments and controls2-53
INTERIOR LIGHTS
&RQGLWLRQ


> (GLW    0RGHO )' @
2-54Instruments and controls
SIC4573
MAP LIGHT CONTROL SWITCH (if so
equipped)
GUID-D030AC73-6A5E-41D1-B4E5-4C8B6A705368The map lights control switch has three posi-
tions: ON
*1, OFF*2and center.
ON positionGUID-96EAA639-DA91-44C2-B280-951FC4FE7379When the switch is in the ON position*1, the
map lights will illuminate.
OFF positionGUID-315173DD-FC92-4382-95FF-5966BDBA76F5When the switch is in the OFF position*2, the
map lights will not illuminate, regardless of the
condition.
Center positionGUID-2C777A6B-3617-446F-8361-A456EE072540When the switch is in the center position, the
map lights will illuminate under the following
conditions:
. ignition switch is placed in the OFF position
Ð remain on for about 15 seconds.
. doors are unlocked by pushing the UN-
LOCK
button (on the Intelligent Key) or
the request switch with the ignition switch in
the LOCK position
Ð remain on for about 15 seconds.
. any door is opened and then closed with the
ignition switch in the LOCK position
Ð remain on for about 15 seconds.
. any door is opened with the ignition switch
in the ACC or ON position
Ð remain on while the door is opened.
When the door is closed, the lights go
off.
The lights will turn off after a period of
time when the lights remain illuminated to
prevent the battery from becoming dis-
charged.
CARGO LIGHTGUID-4E7D7193-19FC-43A7-8050-94552D64EF00The cargo room lights illuminate when the lift
gate is opened. When the lift gate is closed, the
lights will turn off.
&RQGLWLRQ


> (GLW    0RGHO )' @
3 Pre-driving checks and adjustments
Keys...
........................................................................\
...................... 3-2
Intelligent Keys ...
..................................................................... 3-2
Doors ...
........................................................................\
.................... 3-4
Locking with key ...
.................................................................. 3-4
Locking with inside lock knob ...
.......................................... 3-4
Locking with power door lock switch ...
............................ 3-5
Automatic door locks ...
......................................................... 3-5
Child safety rear door lock ...
............................................... 3-6
Intelligent Key system ...
.............................................................. 3-6
Intelligent Key operating range ...
........................................ 3-8
Door locks/unlocks precaution ...
........................................ 3-8
Intelligent Key operation ...
.................................................... 3-9
Battery saver system ...
....................................................... 3-10
Warning lights and audible reminders ...
........................ 3-10
Troubleshooting guide ...
..................................................... 3-11
How to use remote keyless entry function ...
................ 3-12 Hood
...
........................................................................\
................. 3-15
Lift gate ...
........................................................................\
............ 3-16
Front side and rear unique parts (NISMO models) ...
..... 3-17
Fuel-filler door ...
........................................................................\
3-18
Opening the fuel-filler door ...
......................................... 3-18
Fuel-filler cap ...
.................................................................. 3-18
Tilt steering column ...
.............................................................. 3-20
Tilt operation ...
................................................................... 3-20
Sun visors ...
........................................................................\
........ 3-21
Mirrors ...
........................................................................\
............. 3-21
Inside mirror ...
..................................................................... 3-21
Outside mirrors ...
............................................................... 3-22
Vanity mirror ...
..................................................................... 3-23
&RQGLWLRQ


> (GLW    0RGHO )' @
SPA2803
Driver's armrest
LOCKING WITH POWER DOOR LOCK
SWITCH
GUID-5256BBAD-C319-43C6-9C66-55957ADC778FOperating the power door lock switch will lock
or unlock all the doors. The switch is located on
the driver's door armrest.
To lock the doors, push the power door lock
switch to the lock position
*1with the driver's
door open, then close the door.
When locking the door this way, be sure
not to leave the key inside the vehicle.
To unlock the doors, push the power door lock
switch to the unlock position
*2.
Lockout protectionGUID-44F7A60E-83C3-4161-B6E9-F0CE6E62B151Lockout protection function helps to prevent the
keys from being accidentally locked inside the
vehicle.
. When the power door lock switch is moved
to the lock position with the ignition switch
placed in the ACC or ON position and any
door open, all doors will lock and then
unlock automatically.
. When the power door lock switch is moved
to the lock position with the Intelligent Key
left in the vehicle and any door open, all
doors will unlock automatically and a chime
will sound after the door is closed.
AUTOMATIC DOOR LOCKSGUID-FA60553F-2660-4078-8261-73A9AD2C0495.All doors lock automatically when the vehicle
speed reaches 15 MPH (24 km/h) .
. All doors unlock automatically when the
ignition switch is placed in the OFF position.
The automatic unlock function can be
deactivated or activated.
To deactivate or activate the automatic door
unlock system, perform the following procedure.
1. Close all doors.
2. Place the ignition switch in the ON position.
3. Within 20 seconds, push and hold the
power door lock switch to the
(UN-
LOCK) position for more than 5 seconds. 4. When activated, the hazard warning lights
will flash twice. When deactivated, the
hazard warning lights will flash once.
5. The ignition switch must be placed in the OFF and ON position again between each
setting change.
When the automatic door unlock system is
deactivated, the doors do not unlock when the
ignition is placed in the OFF position. To unlock
the door manually, use the inside lock knob or
the power door lock switch.
Pre-driving checks and adjustments3-5
&RQGLWLRQ


> (GLW    0RGHO )' @
3-10Pre-driving checks and adjustments
Locking doorsGUID-07CB5A9E-DF83-455D-A22C-2FF8A457C4EC1. Place the ignition switch in the OFF positionand carry the Intelligent Key with you.*1
2. Close all the doors.*2
3. Push the door handle request switch (dri- ver's or front passenger's)
*Aor the lift
gate request switch
*Bwhile carrying the
Intelligent Key with you.*3
4. All the doors and the lift gate will lock.
5. The hazard indicator flashes twice and the outside chime sounds twice.
*1: Doors will lock with the request switch while the
ignition switch is in the ACC or ON position.
*2: Doors will not lock with the request switch while any door is open.
*3: Doors will not lock with the request switch when the Intelligent Key is left inside the vehicle.
However, when an Intelligent Key is inside the
vehicle, doors can be locked with another
registered Intelligent Key.
Unlocking doorsGUID-FEED93E7-A7E2-406A-BCA7-5A65AC821C9B1. Push the door handle request switch*Aor
the lift gate request switch
*Bwhile
carrying the Intelligent Key with you.
2. The hazard indicator flashes once and out- side chime sounds once. The corresponding
door or the lift gate will unlock. 3. Push the request switch again within 1
minute.
4. The hazard indicator flashes once and out- side chime sounds once again. All the doors
and the lift gate will unlock.
All doors will be locked automatically unless one
of the following operations is performed within 1
minute after pushing the request switch while
the doors are locked.
. Opening any door.
. Pushing the ignition switch.
During this 1-minute time period, if the UNLOCK
button on the Intelligent Key is pushed, all
doors will be locked automatically after another
1 minute.
Opening lift gateGUID-90DFB32E-039E-44A8-95E5-CAC6DC5E9FFF1. Carry the Intelligent Key.
2. Push the lift gate opener switch
*C.
3. The lift gate will unlock.
BATTERY SAVER SYSTEMGUID-817AD6BA-79E5-43BC-A0CC-216A5D867A2AWhen all the following conditions are met for a
period of time, the battery saver system will cut
off the power supply to prevent battery dis-
charge.
. The ignition switch is in the ACC position,
and .
All doors are closed, and
. The shift lever is in the P (Park) position
(Continuously Variable Transmission mod-
els) .
WARNING LIGHTS AND AUDIBLE
REMINDERS
GUID-9651A744-FFA0-4CDB-B228-1C2F7BB0B640To help prevent the vehicle from moving
unexpectedly by erroneous operation of the
Intelligent Key listed on the following chart or
to help prevent the vehicle from being stolen,
chime or beep sounds inside and outside the
vehicle and a warning light illuminates or blinks.
When a chime or beep sounds or the warning
light illuminates or blinks, be sure to check the
vehicle and Intelligent Key.
See ªTroubleshooting guideº (P.3-11) and
ªWarning lights, indicator lights and audible
remindersº (P.2-15).
Intelligent Key system warning light:
P position selecting warning light:
&RQGLWLRQ


> (GLW    0RGHO )' @
SPA2252
*1LOCKbutton
*2UNLOCKbutton
*3PANICbutton
When you lock or unlock the doors, the hazard
indicator will flash and the horn will sound as a
confirmation. For details, see ªSetting hazard
indicator and horn modeº (P.3-13) .
Locking doorsGUID-D5262080-ABD1-4D76-9C95-01FC9F73DFE81. Place the ignition switch in the OFF positionand carry the Intelligent Key with you.*
2. Carry the Intelligent Key with you.
3. Close all the doors.
4. Push the LOCK
button*1on the
Intelligent Key. 5. All the doors and the lift gate will lock.
6. The hazard indicator flashes twice and the
horn chirps once.
*: Doors will lock with the Intelligent Key while the
ignition switch is in the ACC or ON position.
Operate the door handles to confirm that the
doors have been securely locked.
Unlocking doorsGUID-A93EF8B5-C1CC-498F-91E8-A405D427718F1. Push the UNLOCKbutton*2on the
Intelligent Key once.
2. The hazard indicator flashes once. The
driver's door will unlock.
3. Push the UNLOCK
button again within
1 minute.
4. The hazard indicator flashes once. All the doors and the lift gate will unlock.
All doors will be locked automatically unless one
of the following operations is performed within 1
minute after pushing the UNLOCK
button
while the doors are locked.
. Opening any door (including the lift gate) .
. Pushing the ignition switch.
During this 1-minute time period, if the UNLOCK
button is pushed, all doors will be locked
automatically after another 1 minute.
Using panic alarmGUID-513ECE9A-40D5-44E1-AED9-89539DD3CB29If you are near your vehicle and feel threatened,
you may activate the alarm to call attention as
follows:
1. Push the PANIC
button*3on the
Intelligent Key for more than 1 second.
2. The theft warning alarm and headlights will stay on for 25 seconds.
3. The panic alarm stops when:
.It has run for 25 seconds, or.Any of the buttons on the Intelligent Key is pushed. (Note: the PANIC button must
be pushed for more than 1 second.)
Setting hazard indicator and horn modeGUID-3FB89421-3312-403E-A809-6994604156A8This vehicle is set in hazard indicator and horn
mode when you first receive the vehicle.
In hazard indicator and horn mode, when the
LOCK
button*1is pushed, the hazard
indicator flashes twice and the horn chirps once.
When the UNLOCK
button*2is pushed,
the hazard indicator flashes once.
If horns are not necessary, the system can be
switched to the hazard indicator mode.
In hazard indicator mode, when the LOCK
button is pushed, the hazard indicator flashes
twice. When the UNLOCK
button is
pushed, neither the hazard indicator nor the
Pre-driving checks and adjustments3-13
&RQGLWLRQ


> (GLW    0RGHO )' @
3-22Pre-driving checks and adjustments
SPA2143
The night position*1will reduce glare from the
headlights of vehicles behind you at night.
Use the day position
*2when driving in daylight
hours.
WARNING
Use the night position only when ne-
cessary, because it reduces rear view
clarity.
OUTSIDE MIRRORSGUID-510D14F7-96A8-42DE-A36F-11C39E241D3B
WARNING
Objects viewed in the outside mirror on
the passenger side are closer than they
appear. Be careful when moving to the
right. Using only this mirror could cause
an accident. Use the inside mirror or
glance over your shoulder to properly
judge distances to other objects.
SPA2214
Adjusting outside mirrorsGUID-8B70B968-C9B3-4093-8096-7A9C567F354DThe outside mirror control switch is located at
the lower part of the instrument panel.
The outside mirror will operate only when the
ignition switch is in the ACC or ON position.
Move the switch right
*1or left*2to select
the right or left side mirror, then adjust
*3using
the control switch.
&RQGLWLRQ


> (GLW    0RGHO )' @
.To remove moisture or fog on the frontwindow quickly, set the temperature to
the high temperature and the fan speed
to their maximum level.
.After the windshield is cleared, push the
front defroster
button again. (The
indicator light will turn off.)
.When the front defrosterbutton is
pushed, the air conditioner will automa-
tically turn on to defog the windshield.
The outside air circulation mode will be
selected to improve the defogging per-
formance.
.When theposition is selected, the
air recirculation mode cannot be turned
on to prevent the windows from being
fogged up.
Manual operationGUID-3EFCC2B5-D341-447E-B937-C69EC1981FF8The manual mode can be used to control the
heater and air conditioner to your desired
settings.
To turn off the heater and air conditioner, push
the OFF button.
If the Drive Mode is indicated on the screen,
push the CLIMATE button to change to the
Climate Control Mode, then push the OFF
button. Fan speed control:
GUID-F83C168B-173D-4313-B631-F712588C0463Turn the fan speed controldial to adjust the
fan speed.
Air flow control:
GUID-F83C168B-173D-4313-B631-F712588C0463Push the air flow control buttons to change the
air flow mode:
Ð Air flows from the center and side ventilators.
Ð Air flows from the center and sideventilators and foot outlets.
Ð Air flows mainly from the foot outlets.
Ð Air flows from the defroster outlets andfoot outlets.
Temperature control:GUID-F83C168B-173D-4313-B631-F712588C0463Turn the temperature control dial to set the
preferred temperature.
The temperature range is between 608F (188C)
and 908F (328C) .
Air recirculation:
GUID-F83C168B-173D-4313-B631-F712588C0463Push the air intake button to change the air
circulation mode. When the indicator light
illuminates, the flowing air is recirculated inside
the vehicle.
.When the
orposition is selected,
the air recirculation mode cannot be turned
on to prevent the windows from being
fogged up. Outside air circulation:
GUID-F83C168B-173D-4313-B631-F712588C0463Push the air intake button to change the air
circulation mode. When the indicator light
illuminates, the flowing air is drawn from outside
the vehicle.
Automatic air intake control:
GUID-F83C168B-173D-4313-B631-F712588C0463Push and hold the outside air circulation ªº
/air recirculation ª
º button for more than 1.5
seconds to set the automatic control between
the outside air circulation and air recirculation
modes.
When the ª
º or ªº position is selected,
the air recirculation mode does not activate.
When setting the automatic control mode, the
indicator lights ª
º and ªº will blink twice
indicating that the system is in the automatic
control mode.
Heater, air conditioner, audio and phone systems4-33
&RQGLWLRQ