2016 NISSAN JUKE radio


> (GLW    0RGHO )' @
4-36Heater, air conditioner, audio and phone systems
function in your vehicle radio system.
Reception conditions will constantly change
because of vehicle movement. Buildings, terrain,
signal distance and interference from other
vehicles can work against ideal reception.
Described below are some of the factors that
can affect your radio reception.
Some cellular phones or other devices may
cause interference or a buzzing noise to come
from the audio system speakers. Storing the
device in a different location may reduce or
eliminate the noise.
SAA0306
FM radio reception:GUID-F83C168B-173D-4313-B631-F712588C0463Range: FM range is normally limited to 25 to 30
miles (40 to 48 km) , with monaural (single
station) FM having slightly more range than
stereo FM. External influences may sometimes
interfere with FM station reception even if the
FM station is within 25 miles (40 km). The
strength of the FM signal is directly related to the
distance between the transmitter and receiver.
FM signals follow a line-of-sight path, exhibiting
many of the same characteristics as light. For
example they will reflect off objects.
Fade and drift: As your vehicle moves away from
a station transmitter, the signals will tend to fade
and/or drift.Static and flutter: During signal interference from
buildings, large hills or due to antenna position,
usually in conjunction with increased distance
from the station transmitter, static or flutter can
be heard. This can be reduced by lowering the
treble setting to reduce the treble response.
Multipath reception: Because of the reflective
characteristics of FM signals, direct and re-
flected signals reach the receiver at the same
time. The signals may cancel each other,
resulting in momentary flutter or loss of sound.
AM radio reception:
GUID-F83C168B-173D-4313-B631-F712588C0463AM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can be bounced off the
ionosphere and bent back to earth. Because of
these characteristics. AM signals are also
subject to interference as they travel from
transmitter to receiver.
Fading: Occurs while the vehicle is passing
through freeway underpasses or in areas with
many tall buildings. It can also occur for several
seconds during ionospheric turbulence even in
areas where no obstacles exist.
Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic lights.
&RQGLWLRQ


> (GLW    0RGHO )' @
Satellite radio reception (if so equipped):GUID-F83C168B-173D-4313-B631-F712588C0463When the satellite radio is used for the first time
or the battery has been replaced, the satellite
radio may not work properly. This is not a
malfunction. Wait more than 10 minutes with the
satellite radio ON and the vehicle away from any
metal or large buildings for the satellite radio to
receive all of the necessary data.
The satellite radio mode requires an active
SiriusXM Satellite Radio subscription. The sa-
tellite radio is not available in Alaska, Hawaii and
Guam.
Satellite radio performance may be affected if
cargo carried on the roof blocks the satellite
radio signal.
If possible, do not put cargo near the satellite
antenna.
A buildup of ice on the satellite radio antenna
can affect satellite radio performance. Remove
the ice to restore satellite radio reception.
SAA0480
Compact Disc (CD) playerGUID-7A97F8B3-4B15-4845-953F-76679ED50BB3.Do not force a compact disc into the CD
insert slot. This could damage the CD
and/or CD player.
. During cold weather or rainy days, the
player may malfunction due to the
humidity. If this occurs, remove the CD and dehumidify or ventilate the player
completely.
. The player may skip while driving on
rough roads.
. The CD player sometimes cannot func-
tion when the passenger compartment
temperature is extremely high. De-
crease the temperature before use.
. Only use high quality 4.7 in (12 cm)
round discs that have the ªCOMPACT
disc DIGITAL AUDIOº logo on the disc
or packaging.
. Do not expose the CD to direct sun-
light.
. CDs that are of poor quality, dirty,
scratched, covered with fingerprints,
or that have pin holes may not work
properly.
. The following CDs may not work prop-
erly:
ÐCopy control compact discs (CCCD)
Ð Recordable compact discs (CD-R)
Ð Rewritable compact discs (CD-RW)
. Do not use the following CDs as they
may cause the CD player to malfunc-
tion.
Ð3.1 in (8 cm) discs
Heater, air conditioner, audio and phone systems4-37
&RQGLWLRQ


> (GLW    0RGHO )' @
JVH0866X
1. DISP (display) button
2. MEDIA button
3. CD eject button
4. FM´AM button
5. CD button
6. Color display
7. Apps button8. SEEK TRACK (rewind) button
9. Radio SCAN tuning button
10. SEEK TRACK (forward) button
11. BACK button
12. Power button/VOL (volume) control knob
13. RPT (repeat) play button
14. RDM (random) play button15. Radio station preset select buttons
16. TUNE´FOLDER knob
17. ENTER/SETTING button
FM-AM RADIO WITH COMPACT DISC
(CD) PLAYER (if so equipped)
GUID-6DCAFDD0-A600-4480-AA22-B476B499161B
Audio main operationGUID-43F0A38C-D866-41B3-B8ED-B236DBF90316
Head unit:GUID-F83C168B-173D-4313-B631-F712588C0463The auto loudness circuit enhances the low and
high frequency ranges automatically.
Power button/VOL (volume) control
knob:
GUID-F83C168B-173D-4313-B631-F712588C0463Push the Power button/VOL (volume) control
knob to turn on and off the audio system.
Turn the Power button/VOL (volume) control
knob to adjust the volume.
Audio settings:
GUID-F83C168B-173D-4313-B631-F712588C0463The settings screen will appear when the
ENTER/SETTING button is pushed.
The following items are available in the settings
screen.
. Bluetooth
It is possible to set the Bluetooth


> (GLW    0RGHO )' @
4-46Heater, air conditioner, audio and phone systems
Balance adjusts the sound between the left
and right speakers. Fade adjusts the sound
between the front and rear speakers.
Select the ªBassº, ªTrebleº, ªBalanceº or
ªFadeº using the TUNE´FOLDER knob, and
then push the ENTER/SETTING button.
Turn the TUNE´FOLDER knob to adjust the
Bass, Treble, balance and Fade of the
screen to the preferred level. Push the
ENTER/SETTING button to apply the
setting.
. Speed Sensitive Vol.
To change the Speed Sensitive Volume
(Speed Sensitive Vol.) level from off (0) to
5, turn the TUNE´FOLDER knob.
. AUX Vol.
Controls the volume level of incoming sound
when an auxiliary device is connected to the
system. Choose a setting between +1 and
+3 or choose 0 to disable the feature
entirely.
. Brightness and Contrast
Adjust the brightness and contrast of the
screen.
Select ªBrightnessº or ªContrastº using the
TUNE´FOLDER knob and then push the
ENTER/SETTING button. Turn the
TUNE´FOLDER knob to adjust the bright-
ness and contrast of the screen to the preferred level. Push the ENTER/SETTING
button to apply the setting.
. Clock Adjust
Adjust the clock according to the following
procedure.
1) Select ªClock Adjustº using the
TUNE´FOLDER knob and then push
the ENTER/SETTING button.
2) Adjust the hour with the TUNE´FOLDER knob and then push the ENTER/
SETTING button.
3) Adjust the minute with the TUNE´FOLDER knob and then push
the ENTER/SETTING button.
24 hour clock is not available.
. On-Screen Clock
When this item is turned on, a clock is
always displayed in the upper right corner of
the screen.
Select the ªOn-Screen Clockº using the
TUNE´FOLDER knob and then push the
ENTER/SETTING button. You can toggle
between ON and OFF using the
TUNE´FOLDER knob.
. RDS Display (if so equipped)
RDS (radio data system) information can be
shown on the display. Select ªRDS Displayº
using the TUNE´FOLDER knob and then
push the ENTER/SETTING button. You can toggle between ON and OFF using the
TUNE´FOLDER knob. Push the ENTER/
SETTING button to apply the setting.
. Language Select
The language settings can be changed.
Select ªLanguage Selectº using the
TUNE´FOLDER knob and then push the
ENTER/SETTING button. Use the
TUNE´FOLDER knob to select the preferred
language. Push the ENTER/SETTING but-
ton to apply the setting.
DISP button:GUID-F83C168B-173D-4313-B631-F712588C0463Display of the screen can be canceled by
pushing the
button. You can still listen to
music that is being played back even while the
screen display is turned off. If you want to
display the screen again, push the
button
once more. Pushing some of the audio source
buttons will also turn the screen back on and
display the screens of the corresponding
sources.
MEDIA button:GUID-F83C168B-173D-4313-B631-F712588C0463Pushing thebutton will switch the audio
source as follows:
USB/iPod ?Bluetooth Audio ?AUX ?USB/
iPod
&RQGLWLRQ


> (GLW    0RGHO )' @
Apps button:GUID-F83C168B-173D-4313-B631-F712588C0463Thebutton launches the Smartphone
Integration mode. See ªNissanConnectSMApp
smartphone integrationº (P.4-75) .
FM-AM Radio operationGUID-F6D3CBA1-CE19-4A9D-8F43-C15C732220C2
radio (FM´AM) band select:GUID-F83C168B-173D-4313-B631-F712588C0463Push thebutton to change the band as
follows:
AM ?FM1 ?FM2? AM
TUNE (Tuning):
GUID-F83C168B-173D-4313-B631-F712588C0463Turn the TUNE´FOLDER knob for manual tuning.
SEEK tuning:GUID-F83C168B-173D-4313-B631-F712588C0463Push theorbutton to tune from low to
high or high to low frequencies and to stop at
the next broadcasting station.
SCAN tuning:GUID-F83C168B-173D-4313-B631-F712588C0463Push thebutton to tune from low to high
frequencies and stop at each broadcasting
station for several seconds. Pushing the button
again during this several seconds period will
stop SCAN tuning and the radio will remain
tuned to that station. If the
button is not pushed within this
period, SCAN tuning moves to the next station.
toRadio memory buttons:GUID-F83C168B-173D-4313-B631-F712588C0463Up to 12 stations can be set for the FM band (6
each for FM1 and FM2) and 6 stations can be
set for the AM band.
1. Choose the radio band using the
button.
2. Tune to the desired station.
3. Push and hold the desired station preset button
tountil beep sounds.
4. The station indicator will then come on. The station is now set to the button memory.
5. Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if the fuse
opens, the station memory will be erased. In that
case, reset the desired stations.
CD player operationGUID-248E139A-04E4-4AD2-8E33-2281B71D316APlace the ignition switch in the ON or ACC
position. Insert the Compact Disc (CD) into the
slot with the label side facing up. The CD will be
guided automatically into the slot and start
playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If another audio source is already operating, it
will automatically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the Power button will start
the CD.
CD PLAY:GUID-F83C168B-173D-4313-B631-F712588C0463When the CD button is pushed while a CD is
loaded, the CD will start playing.
SEEK TRACK:GUID-F83C168B-173D-4313-B631-F712588C0463When theorbutton is pushed and hold
while the CD is being played, the CD will play
while fast forwarding or rewinding. When the
button is released, the CD will return to normal
play speed.
When the
orbutton is pushed while
the CD is being played, the next track or the
beginning of the current track on the CD will be
Heater, air conditioner, audio and phone systems4-47
&RQGLWLRQ


> (GLW    0RGHO )' @
JVH1055X
1. XM band select button
2. CD eject button
3. FM´AM button
4. MEDIA button
5. Color display
6. Apps button
7. Radio CAT (category)/REW (rewind) button forSEEK/TRACK 8. Radio SCAN tuning button
9. Radio CAT (category)/FF (fast forward) button
for SEEK/TRACK
10. BACK button
11. DISP (display) button
12. Power button/VOL (volume) control knob
13. RPT (repeat) play button 14. RDM (random) play button
15. Radio station preset select buttons
16. ENTER/SETTING button/TUNE´SCROLL con-
trol knob
FM-AM-SAT RADIO WITH COMPACT
DISC (CD) PLAYER (Type A) (if so
equipped)
GUID-4352CB40-F655-4D9F-9183-1F90386111A6For all operation precautions, see ªAudio opera-
tion precautionsº (P.4-35) .
.No satellite radio reception is available when
the SAT band option is selected unless the
optional satellite receiver and antenna are
installed, and there is an active SiriusXM
Satellite Radio subscription.
. The satellite radio mode requires an active
SiriusXM Satellite Radio subscription. The
satellite radio is not available in Alaska,
Hawaii and Guam.
. It may take some time to receive the
activation signal after subscribing the Sir-
iusXM Satellite Radio. After receiving the
activation signal, an available channel list will
be automatically updated in the radio. Push
the ignition switch from LOCK to ACC to
update the channel list.
Heater, air conditioner, audio and phone systems4-53
&RQGLWLRQ


> (GLW    0RGHO )' @
.Language Select
The language settings can be changed.
Select ªLanguage Selectº using the TU-
NE´SCROLL control knob and then push the
ENTER/SETTING button. Use the TU-
NE´SCROLL control knob to select the
preferred language. Push the ENTER/
SETTING button to apply the setting.
DISP button:GUID-F83C168B-173D-4313-B631-F712588C0463Display of the screen can be canceled by
pushing the
button. You can still listen to
music that is being played back even while the
screen display is turned off. If you want to
display the screen again, push the
button
once more. Pushing some of the audio source
buttons will also turn the screen back on and
display the screens of the corresponding
sources.
MEDIA button:GUID-F83C168B-173D-4313-B631-F712588C0463Pushing thebutton will switch the audio
source as follows:
CD ?USB/iPod ?Bluetooth Audio ?AUX ?
CD
Apps button:GUID-F83C168B-173D-4313-B631-F712588C0463Thebutton launches the Smartphone
Integration mode. See ªNissanConnectSMApp smartphone integrationº (P.4-75) .
FM-AM-SAT Radio operationGUID-30B56C20-92D8-4B10-A97C-E70DB83836B6
radio (FM´AM) band select:GUID-F83C168B-173D-4313-B631-F712588C0463Pushing the FM´AM button will change the band
as follows:
AM
?FM1 ?FM2 ?AM
radio (SAT) band select:GUID-F83C168B-173D-4313-B631-F712588C0463Pushing the XM band select button will change
the band as follows:
XM1 ?XM2 ?XM3 ?XM1
When the XM band select button is pushed
while the ignition switch is in the ACC or ON
position, the radio will come on at the channel
last played.
The last channel played will also come on when
the Power button is pushed to ON.
The satellite radio is not available in Alaska,
Hawaii and Guam.
If another audio source is playing when the radio
band select button is turned to ON, the audio
source will automatically be turned off and the
last radio channel played will come on.
When the stereo broadcast signal is weak, the
radio will automatically change from stereo to
monaural reception. TUNE (Tuning):
GUID-F83C168B-173D-4313-B631-F712588C0463.
For AM and FM radio
Turn the radio TUNE´SCROLL control knob
for manual tuning.
. For SiriusXM Satellite Radio
Turn the radio TUNE´SCROLL control knob
to seek channels from all of the categories
when any category is not selected.
SEEK tuning/CAT (category):GUID-F83C168B-173D-4313-B631-F712588C0463.For AM and FM radio
Push the SEEK button
orto tune
from low to high or high to low frequencies
and to stop at the next broadcasting station.
. For SiriusXM Satellite Radio
Push the SEEK button
orto tune to
the first channel of the next or previous
category.
SCAN tuning:GUID-F83C168B-173D-4313-B631-F712588C0463Push the SCAN tuning button to tune from low
to high frequencies and stop at each broad-
casting station for several seconds. Pushing the
button again during this several seconds period
will stop SCAN tuning and the radio will remain
tuned to that station.
If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next
Heater, air conditioner, audio and phone systems4-55
&RQGLWLRQ


> (GLW    0RGHO )' @
4-56Heater, air conditioner, audio and phone systems
station.
toStation memory operations:GUID-F83C168B-173D-4313-B631-F712588C046312 stations can be set for the FM band (6 each
for FM1 and FM2) and 6 stations can be set for
the AM band.
1.Choose the radio band using the
button.
2. Tune to the desired station.
3. Push and hold the desired station preset button
tountil beep sounds.
4. The station indicator will then come on. Memorizing is now complete.
5. Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if the fuse
opens, the station memory will be erased. In that
case, reset the desired stations.
CD player operationGUID-AD8D542A-ED45-492B-83CE-102DF83F1B07Place the ignition switch in the ON or ACC
position, and insert the compact disc (CD) into
the slot with the label side facing up. The CD will
be guided automatically into the slot and start
playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If another audio source is already operating, it
will automatically turn off and the CD will play.
If the system was turned off while the CD was
playing, pushing the Power button will start the
CD.
PLAY:GUID-F83C168B-173D-4313-B631-F712588C0463With a CD loaded, press thebutton until
the CD mode is displayed on the screen.
Next/Previous Track and Fast
Forward/Rewind :
GUID-F83C168B-173D-4313-B631-F712588C0463When theorbutton is pushed and hold
while the CD is being played, the CD will play
while fast forwarding or rewinding. When the
button is released, the CD will return to normal
play speed.
When the
orbutton is pushed while
the CD is being played, the next track or the beginning of the current track on the CD will be
played. Push the
button again to select the
previous track.
RPT (repeat) button:GUID-F83C168B-173D-4313-B631-F712588C0463When thebutton is pushed while the CD is
played, the play pattern can be changed as
follows:
(CD)
(Normal) Û1 Track Repeat
(CD with compressed audio files)
(Normal) ?1 Folder Repeat ?1 Track Repeat
? (Normal)
RDM (random) button:GUID-F83C168B-173D-4313-B631-F712588C0463When thebutton is pushed while a CD is
being played, the play pattern can be changed
as follows:
(CD)
(Normal) Û1 Disc Random
(CD with compressed audio files)
(Normal) ?1 Disc Random ?1 Folder
Random ?(Normal)
CD eject button:GUID-F83C168B-173D-4313-B631-F712588C0463When thebutton is pushed with the CD
loaded, the CD will be ejected.
&RQGLWLRQ