2016 MITSUBISHI iMiEV battery

Instrument cluster
Features and controls 5-41
5
N00573000010
This value (A) shows the outside temperature of the vehicle.
If the outside temperature drops below approximately 37 °F (3 °C), the alarm sounds and the outside air temperature warning indi-cator (B) flash for a
pproximately 10 seconds
to show there is a danger the road might be icy.
N00573100011
When the electric motor switch is in the“ACC” or “ON” position,
pressing the selec-
tor button (A) for more than 2 seconds will switch the outside temperature unit between°F and °C.
N00572800024
The energy level gauge indicates the remain-ing power in the main
drive lithium-ion bat-
When the main drive lithium-ion battery is charged, the approximate cruising range isupdated.
Outside temperature display
NOTE
 The outside temperature can be displayed from -40

Instrument cluster 5-42 Features and controls
5
tery during charging or when the electric motor switch is in the “ON” position.
N00572900025
When the electric motor switch is in the “ON” position and the
remaining bar of the
energy level gauge shows 2 bars or less, thewarning indicator (A) and the charging bars (B) flash as follows: When the energy level gauge shows 2 bars: The warning indicator flashes.When the energy level gauge shows 1 bar: The warning indicator and the charging bars flash alternately. Recharge the main drive lithium-ion battery as soon as possible.
F- Battery is fully charged. E- Charge the battery.
NOTE
 The charging indicator
is also illuminated
during charging. Refer to “Charging indi
cator” on page 5-44.
Low energy warning indicator
NOTE
If the energy level gauge shows 0 bars during use of the air conditioning, the cooling orheating may stop opera
tion and the mode is
changed to fan only.  If the energy level gauge shows 0 bars, the power down warning light
is illuminated to
control the output.  If the energy level gauge shows 2 bars while the main drive lithium-ion battery is being charged, the warning i
ndicator flashes. If the
energy level gauge shows 1 bar while the main drive lithium-ion battery is being charged, the warning indicator and the charg-ing bars flash alternately.
BK0220401US.book 42 ページ ２０１５年６月３日　水曜日　午前７時４２分

Indicator and warning light package
Features and controls 5-43
5
N00519801888
Indicator and warning light package 1- Low energy warning indicator
 P.5-42
2- Selector lever
position indicator
 P.5-21
3- Acoustic Vehicle Alerting System
( AVA S ) i n d i c a t o r
 P.5-23
4- High-beam indicator
 P.5-44
5- Turn-signal indicators/Hazard warning
lights
 P.5-44
6- Position indicator
 P.5-44
7- Front fog light indicator
 P.5-44
8- Service reminder
 P. 5 - 3 8
9- Outside air temperature warning indi-
cator
 P. 5 - 4 1
10- Regenerative brake system indicator
 P.5-44
11- Ready indicator
 P.5-44
12- Tire pressure moni
toring system warn-
ing light
 P.5-31
13- 12V starter battery charging system
warning light
 P.5-45
14- Electric power steering system warning
light
 P.5-28
15- Electric motor unit warning light
 P.5-45
16- Brake warning light
 P. 5 - 4 4
17- Anti-lock braking system warning light
 P.5-26
18- Power down warning light
 P.5-46
19- Active stability control (ASC) indicator
 P.5-30
20- Active stability control (ASC) OFF
indicator
 P. 5 - 3 0
21- Charging indicator
 P.5-44
22- Theft-alarm indicator
 P.5-12
23- Door-ajar warning light
 P.5-45
24- Driver’s seat belt reminder/warning
light
 P. 4 - 1 0
25- Supplemental Restra
int System (SRS)
warning light
 P.4-13
BK0220401US.book 43 ページ ２０１５年６月３日　水曜日　午前７時４２分

Warning lights
Features and controls 5-45
5
N00573500028
This light will illuminate when there is a problem with the charging system for the 12Vstarter battery. Normally, when the electric motor switch is turned to the “ON” position, this light will
illuminate. Then, when the electric motor unit is started and the ready indicator illuminates,the light will go out.
N00520900316
This light comes on when any door or liftgate is open or not completely closed. When the vehicle is moving at more than 5mph (8 km/h) and any door or liftgate is open or ajar, a tone will sound 16 times and the warning light will fl
ash 16 times to inform
the driver that a door or liftgate is not prop- erly shut.
N00573600029
This warning light will illuminate when there is a problem with a high voltage component. Refer to “Service prec
autions” on page 9-2.
• The brake warning light does not come on when the electric motor switch isturned to the “ON” position.• The brake warning light does not illumi-nate while the parking brake is appliedand the electric motor switch is in the “ON” position. • The brake warning
light stays on when
the parking brake is not applied.NOTE
 When the brake warning light illuminates, the warning buzzer may also sound.  When the brake pedal has been repeatedly depressed over a short period of time, the brake warning light may come on and thebrake warning buzzer may sound. The ser- vice brake system is working normally, if the warning light goes out and the buzzer stopssounding in a few seconds.
12V starter battery charging system warning light
WA R N I N G
CAUTION If the warning light stays on after the ready indicator illuminates, there may be a prob-lem with the charging system for the 12V starter battery.• Immediately park your
vehicle in a safe
place and contact a cert
ified i-MiEV dealer.
• Do not charge the
12V starter battery.
Door-ajar warning light and buzzer
CAUTION Before driving, make sure that the door-ajar warning light is off.
NOTE
 The flashing of the warning light and the buzzer can be disabled.For further details, plea
se contact a certified
i-MiEV dealer.  When the driver’s door is open, the door-ajar warning buzzer does not sound because the electric motor reminder sounds instead.
Electric motor unit warning light
CAUTION If this light illuminates while driving, imme- diately park your vehicle in a safe place andcontact a certified i-MiEV dealer.
BK0220401US.book 45 ページ ２０１５年６月３日　水曜日　午前７時４２分

Combination headlights and dimmer switch 5-46 Features and controls
5
N00573700020
If the warning light illuminates when the out- side air temperature is very low, move thevehicle to a warmer location.
If the warning light illuminates after the vehi- cle has been driven continuously uphill orwhen the outside air temperature is very high, stop the vehicle in a safe place so the electric motor unit and/or the main drive lithium-ionbattery can cool down. When they have cooled down, the warning light will go off. If the warning light does not turn off, contact acertified i-MiEV dealer.
N00522501805
Rotate the switch to operate the lights.
Power down warning light
If this warning light illumi-nates, the power provided by the electric motor will be reduced and the vehicle willbe only able to move at low speeds. This warning light will illu-minate;  When the energy level in the main drive lithium-ion battery is near empty.  When temperature of the electric motor unit or the main drive lithium-ion battery is too high or toolow.  When voltage of the main drive lithium-ion batterybecomes low.
If the energy level gauge shows 0 bar, the main drivelithium-ion battery is near empty and must be charged as soon as possible. Refer to“Charging” on page 3-13.
NOTE
 When the power down warning light illumi- nates, avoid rapid st
arts and aggressive
acceleration.  Illumination of the
power down warning
light does not indica
te a malfunction.
 If the power down warn
ing light illuminates
while the air conditioning is used, the cool- ing or heating may stop operating and only the fan will operate.
Combination headlights and dimmer switch Headlights
NOTE
 Do not leave the headli
ghts and other lights
on for a long period of time while the readyindicator is not illu
minated. A run down 12V
starter battery
could result.
 When it rains, or wh
en the vehicle has been
washed, the inside of the lens sometimes becomes foggy. This is the same as whenwindow glass mists up on a humid day, and does not indicate a pr
oblem. When the light
is switched on, the heat will dry out the fog.However, if water collects inside the light, have it checked by a certified i-MiEV dealer.
BK0220401US.book 46 ページ ２０１５年６月３日　水曜日　午前７時４２分

Turn signal lever
Features and controls 5-49
5
N00522600506
When changing lanes, or to making a gradual turn, hold the lever in the “lane change” posi- tion (1). It will return to the neutral positionwhen you let go. Use the full position (2) when making a normal turn. The lever will return to the neutral position when the turn iscomplete. There may be times when the lever does not return to th
e neutral position. This
usually happens when
the steering wheel is
turned only slightly. You
can easily return the
lever by hand. Also, when you move the lever to (1) slightlythen release it, the turn signal lights and indi- cator in the instrument cluster will flash three times.
N00522700305
If you press the flasher switch, the front andrear turn signals will flash intermittently, and so will the hazard warning lights. This is an emergency warning system and should not beused when the vehicle is in motion, except for emergencies. If you need to leave your
vehicle, the flashers
will keep working after the key is removed from the electric motor switch.
 If you turn the lights off with the headlights set to high-beam illumi
nation, the headlights
are automatically returned to their low-beamsetting when the combination headlights and dimmer switch is next turned to the “ ”
Turn signal lever
NOTE
NOTE
 A light in the instrument panel flashes to show when the front and rear turn signallights are working properly. If this light flashes fast
er than usual, check
for a burned out light
bulb or malfunctioning
connection. If the panel light does not come on when the lever is moved, check
for a blown fuse or a
burned out bulb in the panel. Have the vehicle insp
ected by a certified i-
MiEV dealer.  It is possible to modify functions as follows: • Deactivate the turn signal light 3-flash function for lane changes. • Adjust the time required to operate the lever for the 3-flash function. See a certified i-MiEV dealer for details.
Hazard warning flasher switch
NOTE
 If you keep the flashers on for a long period of time while the ready
indicator is not illu-
minated, the 12V starte
r battery could go flat
and the electric motor unit could be impossi- ble to start.
BK0220401US.book 49 ページ ２０１５年６月３日　水曜日　午前７時４２分

Bluetooth® 2.0 interface (if so equipped) 5-54 Features and controls
5
Bluetooth
® music player, from the vehicle’s
speakers.The system is equipped with a voice recogni- tion function, which allows you to make hands-free calls by s
imple switch operations
and voice command operations using a defined voice tree. The Bluetooth
® 2.0 interface can be used
when the electric motor switch is in the “ON” Before you can use the Bluetooth
® 2.0 inter-
face, you must pa
ir the Bluetooth
® device
and Bluetooth
® 2.0 interface. Refer to “Con-
necting the Bluetooth
® 2.0 interface and
Bluetooth
® device” on page 5-59.
Bluetooth
® is a registered trademark of
BLUETOOTH SIG, INC.
Steering control sw
itch and microphone
 P.5-55 Voice recognition function
 P.5-56
Useful voice commands
 P.5-56
Speaker enrollment function
 P. 5 - 5 8
Connecting the Bluetooth
® 2.0 interface and
the Bluetooth
® device
 P.5-59
Operating a music player connected via Blue- tooth
®  P.5-63
How to make or receive hands-free calls  P.5-63 Phonebook function
 P.5-66
WA R N I N GAlthough the Bluetooth
® 2.0 interface
allows you to make ha
nds-free calls, if you
choose to use the cellular phone whiledriving, you must not allow yourself to be distracted from the sa
fe operation of your
vehicle. Anything, including cellularphone usage, that distracts you from the safe operation of your vehicle increases your risk of
an accident.
Refer to and comply
with all state and
local laws in your area regarding cellularphone usage while driving.NOTE
 If the electric motor sw
itch is left in the
“ACC” position, the
accessory power will
automatically turn off after a certain period of time and you will no longer be able to use the Bluetooth
® 2.0 interface. The accessory
power comes on again if the electric motor switch is turned from the “ACC” position.Refer to “ACC power
auto-cutout function”
on page 5-19.  The Bluetooth
® 2.0 interface
cannot be used
if the Bluetooth
® device has a dead battery
or the device power is turned off.  Hands-free calls will
not be possible if your
phone does not have
service available.
 If you place the Bluetooth
® device in the
luggage compartment, you may not be able to use the Bluetooth
® 2.0 interface.
 Some Bluetooth
® devices are not compatible
with the Bluetooth
® 2.0 interface.
 You can confirm the Link System software version by pressing the HANG-UP button 3times (press and hold 2 times and then press briefly) within 10 seconds.WA R N I N G
 For detail of the Bluetooth
® 2.0 interface,
refer to the following web site: [For vehicles sold in U.S.A.] You can access the Mits
ubishi Motors North
America website. [For vehicles so
ld in Canada]
You can access the Mitsubishi Motors web-site. Please read and agree to the “Warning about Links to the Web Sites of Other Companies”,the websites mentione
d above may connect
you to websites other than the Mitsubishi Motors website.http://www.mitsubishi
-motors.com/en/prod-
ucts/index.html  Software updates by cellular phone/digital audio device manufacturers may change/alter devi
ce connectivity.
NOTE
BK0220401US.book 54 ページ ２０１５年６月３日　水曜日　午前７時４２分

Sun visors 5-76 Features and controls
5
N00524600340
Fold the sun visor downward (1) to reduce front glare while driving. To reduce side glare, turn the visor to the side (2). A vanity mirror is fitted to the back of the sun visor.
Cards can be slipped into the front (A) of the lid of the vanity mirror.
N00525000602
The accessory can be operated when the elec-tric motor switch is in the “ON” or “ACC” To use a “plug-in” type accessory, open thecover, then insert the plug in the socket.
Sun visors Vanity mirror
Card holder
12 V power outlet
CAUTION Be sure to use a “plug-in” type accessory operating at 12 V and 120 W or less. Be aware that using
electronic equipment
with the ready indicator off may run the 12 Vstarter battery down. When the 12 V power outlet is not in use, be sure to close the 12 V power outlet cover. This will prevent the 12 V power outlet from becoming dirty and possi
bly short-circuiting.
BK0220401US.book 76 ページ ２０１５年６月３日　水曜日　午前７時４２分