2016 MERCEDES-BENZ S-Class SEDAN page 52

Publication details
Internet
Further information about Mercedes-Benz
vehicles and about Daimler AG can be found
on the following websites:
http://www.mbusa.com (USA only)
http://www.mercedes-benz.ca (Canada
only)
Editorial office
You are welcome to forward any queries or
suggestions you may have regarding this
Operator's Manual to the technical documen-
tation team at the following address:
Daimler AG, HPC: CAC, Customer Service,
70546 Stuttgart, Germany
©Daimler AG: Not to be reprinted, translated
or otherwise reproduced, in whole or in part,
without written permission from Daimler AG.
Vehicle manufacturer
Daimler AG
Mercedesstraße 137
70327 Stuttgart
Germany
Symbols
In this Operator's Manual you will find the fol-
lowing symbols:
GWARNING
Warning notes make you aware of dangers
which could pose a threat to your health or
life, or to the health and life of others.
HEnvironmental note
Environmental notes provide you with infor-
mation on environmentally aware actions or
disposal.
!Notes on material damage alert you to
dangers that could lead to damage to your
vehicle.
iPractical tips or further information that
could be helpful to you.
X This symbol indicates an instruction
that must be followed.
X Several of these symbols in succes-
sion indicate an instruction with sev-
eral steps.
(Y
page) This symbol tells you where you can
find more information about a topic.
Dis‐
play
This font indicates a display in the
multifunction display/COMAND dis-
play.
Parts of the software in the vehicle are pro-
tected by copyright
©2005
The FreeType Project
http://www.freetype.org. All rights
reserved.
As at 24.09.2014

Rselect a destination on the map
Rsave entries
The controller can be:
Rturned
Rslid left or right1
Rslid forwards or back 4
Rslid diagonally2
Rpressed briefly or pressed and held
Touchpad
Alternatively, COMAND may be equipped
with a touchpad instead of a telephone key-
pad.
As an alternative to the controller, the touch-
pad enables menu items to be selected and
character entry including handwriting recog-
nition, for example.
XTo activate the touchpad: press the sur-
face of the touchpad.
Further information (
Ypage 32).
Basic COMAND functions
Switching COMAND on/off
XPress the ubutton on the center con-
sole to the right of the controller.
When you switch on COMAND, a warning
message will appear. COMAND calls up the
previously selected menu.
If you switch off COMAND, playback of the current media source will also be switched
off.
Adjusting the volume
Adjusting the volume for media sources
XTurn the thumbwheel to the right of the
controller.
or
XPress the WorX button on the mul-
tifunction steering wheel.
The volume of the media source currently
selected changes.
Adjusting the volume for traffic
announcements and navigation
announcements
During traffic or navigation announcements:
XTurn the thumbwheel to the right of the
controller.
or
XPress the WorX button on the mul-
tifunction steering wheel.
iYou can set the volume for navigation
announcements to be different from the
volume of the respective media source.
Adjusting the volume for phone calls
You can adjust the volume for hands-free
mode during a telephone call.
XTurn the thumbwheel to the right of the
controller.
or
XPress the WorX button on the mul-
tifunction steering wheel.
iSetting the volume for the Voice Control
System voice output, see the separate
operating instructions.
Basic COMAND functions27
Overview and operation

Switching the sound on or off
Media source sound
XPress the thumbwheel beside the control-
ler.
or
XPress the 8button on the multifunction
steering wheel.
iIf the audio output is switched off, the
status line will show the 8symbol. If
you switch the media source or change the
volume, the sound is automatically
switched on.
iEven if the sound is switched off, you will
still hear navigation system announce-
ments.
Switching navigation announcements
off and on again
XTo switch off navigation announce-
ments: press the thumbwheel beside the
controller during the announcement.
The Spoken
drivingrecommendations
have been deactivatedmessage
appears.
XTo switch navigation announcements
back on: switch COMAND off and then on
again (
Ypage 27).
or
XStart a new route calculation (Ypage 90).
or
XSelect +: while route guidance is active,
show the menu and press the controller
(
Ypage 111).
Function menu
XPress the Õbutton or the ß,$,
%, or Øbutton.
Media: the basic display for the last media
source set appears.
Navigation: the map or the last navigation
menu called up appears.
Radio: the basic menu of the last radio
mode set appears.
Communication: the basic menu of the
last communication function set appears
(telephone, address book, Internet).
Vehicle functions: the basic display
appears.
XFor radio, media and telephone: press
the $, Õor% button repeatedly.
The menu for the available radio modes,
media sources or communication functions
is displayed.
28Basic COMAND functions
Overview and operation

can be made from both sides. In this case,
the last setting made takes precedence.
RRequirement for Internet use (USA):
mbrace must be activated for Internet
access in COMAND on the driver's side
(
Ypage 176).
RRequirement for Internet use (Canada): a
mobile phone must be connected via Blue-
tooth
®or USB to COMAND on the driver's
side (
Ypage 176).
RThe Internet can be separately used by both
the driver and front passenger at the same
time.
RThe multifunction steering wheel can be
used to control the functions which relate
to the driver's side, but not for the front-
passenger side.
RThe driver can lock or unlock the other
screens (override feature) (
Ypage 76).
Switching SPLITVIEW on/off
From the driver's side
XTo activate: press theØbutton.
The Vehicle menu appears.
XSlide 6the controller.
The menu bar is shown.
XTo select ICON_SplitView On, turn and
press the controller.
The ù SPLITVIEW symbol appears in the
status bar. The menu item in the lower
menu bar changes to ù
Off.
The front passenger sees the display of the
function last activated. If the switch-on
time was longer than 30 minutes previ- ously, the display from the driver's side is
shown.
XTo deactivate:
selectùOffby turning
and pressing the controller.
The display changes to ICON_SplitView
On.
ù is hidden in the status bar.
XTo lock/unlock SPLITVIEW: proceed as
described under "Locking/unlocking the
rear-compartment displays" (
Ypage 76).
Instead of selecting a rear-compartment
display, select SplitView
.
From the front-passenger side
Operation takes place via the COMAND
remote control (
Ypage 273).
XTo activate:select the SPLITVIEW display
by turning thumbwheel :until the SPLIT-
VIEW icon appears in the window.
XPress the ubutton.
XTo deactivate: press buttonu.
The display changes to ICON_SplitView
On.
The SPLITVIEW symbol is hidden in the sta-
tus bar.
The menu called up on the driver's side is
shown.
30SPLITVIEW
Overview and operation

SPLITVIEW is activated with the last settings,
if:
RCOMAND is switched off by removing the
key from the ignition lock while SPLITVIEW
is activated
Rand switched on again within 30 minutes
If COMAND is switched on again after more
than 30 minutes, SPLITVIEW is not activa-
ted.
If SPLITVIEW is activated on the front-
passenger side, the settings from the driver's
side will be used.
In media mode
SPLITVIEW can be activated from any media
mode (e.g. Media Interface).
XTo activate: slide6the controller.
The menu bar is shown.
XTo select Options, turn and press the con-
troller.
A menu appears.
XSelect Start Application at Other
Seat.
A menu appears.
XSelect SplitView.
A window with the Starting
Sourcein
SplitView…message appears.
SPLITVIEW switches on. The ùsymbol
appears in the status bar.
XTo deactivate: from the driver's side, use
the Ø button (
Ypage 30).
XFrom the front-passenger side, use the
COMAND remote control.
XAdditional options: to selectAddi‐
tionalOptions…, turn and press the con-
troller.
A menu appears.
XTo switch SPLITVIEW on/off: proceed as
described under "Switching the rear-com-
partment displays on/off" (
Ypage 76).
Instead of selecting a rear-compartment
display, select SplitView
.
XTo lock/unlock SPLITVIEW: proceed as
described under "Locking/unlocking the
rear-compartment displays" (
Ypage 76).
Instead of selecting a rear-compartment
display, select SplitView
.
Transferring a destination to the
driver
Using SPLITVIEW you can select a destination
from the front-passenger side and transfer
this to the driver's side.
XSwitch on SPLITVIEW (Ypage 30).
XTo selectICON_SplitView On, turn and
press the controller.
The SPLITVIEW symbol appears in the dis-
play and the ùdisplay switches to ù
Off.
XSelect®in the main function bar with the
COMAND remote control.
A menu appears.
XUsing the COMAND remote control, select
Mercedes-Benz Apps
.
You see the selection of Mercedes-Benz
Apps.
XSelect Google Local Searchwith the
COMAND remote control (
Ypage 182).
A menu appears.
XSelect a search position, e.g. In the
Vicinity of the Destination.
A menu appears.
XSelect a type of search inquiry, such as
Enter search term
.
An input field appears.
SPLITVIEW31
Overview and operation

XEnter the destination using the COMAND
remote control and press thebbutton.
The Google™ results list appears.
XSelect the destination using the COMAND
remote control.
A menu appears.
XSelect Set as Destination.
XThe prompt Accept the navigation
data from Mercedes-Benz Apps?
appears on the driver's side.
XSelectYesorNo.
If you select Yes
, the navigation data is
used for route guidance.
Touchpad
Touchpad overview
!
Do not use any sharp objects on the
touchpad. This could damage the touch-
pad.
:Touch-sensitive surface
;Favorites button
=Calls up quick access for audio and tele-
phone
?Back button
Using the touchpad, you can:
Rselect menu items in the display
(
Ypage 32).
Renter characters (handwriting recognition)
(
Ypage 34).
Rcontrol the active audio source
(
Ypage 37).
Rcreate, manage and call up favorites
(
Ypage 43).
Renter destinations in navigation.
Rsave entries.
Further information on operating the touch-
pad (
Ypage 32).
Switching the touchpad on/off
XPress the Øbutton.
The vehicle menu is displayed.
XTo select System Settings: slide6,
turn and press the controller.
A menu appears.
XTo select Activate Touchpad, turn and
press the controller.
The touchpad is switched on Oor off ª.
Operating the touchpad
Selecting a menu item
XUse one finger to touch the touch-sensitive
surface.
XGlide your finger up, down, to the left or
right.
The selection in the display moves in
accordance with the direction of move-
ment.
You can navigate in lists or menus in this way.
32Touchpad
Overview and operation

Confirming a selection
Do not press your finger too hard on the
touchpad. This could cause malfunctions.
XUse one finger to press the touch-sensitive
surface until you reach the pressure point.
A menu, an option or an application is star-
ted.
Calling up quick access for audio and
telephone
XUse two fingers to touch the lower part of
the touch-sensitive surface.
XGlide your fingers up.
Quick access is displayed.
Further information on quick access for audio
and telephone (
Ypage 37).
Hiding the quick access for audio and
telephone
XUse two fingers to touch the touch-sensi-
tive surface.
XGlide your fingers down.
Quick access is hidden.
Operating the control for vehicle and
sound settings
XTouch the touch-sensitive surface with two fingers, spaced slightly apart.
XTurn both fingers clockwise.
The control setting is increased.
or
XTurn both fingers counter-clockwise.
The control setting is decreased.
Touchpad33
Overview and operation

Moving the map
XUse one finger to press the touch-sensitive
surface until you reach the pressure point.
The crosshair is shown.
XTouch the touch-sensitive surface again
with one finger.
XGlide your finger in any direction.
The map is moved is the direction of move-
ment.
Zooming in on the map
XTouch the touch-sensitive surface with twofingers, spaced slightly apart.
XGlide your fingers away from each other.
The map scale is magnified.
Zooming out of the map
XTouch the touch-sensitive surface with twofingers, spaced far apart.
XGlide your fingers towards each other.
The map scale is reduced.
Handwriting recognition
Handwriting recognition overview
You can use handwriting recognition for text,
numbers or characters in any input line.
:Active input line
;Enters a space (Ypage 35)
=Illustration of the touch-sensitive surface
?Deletes characters (Ypage 35)
If the character that you have entered can be interpreted in different ways, these options
are displayed. More information on the char-
acter suggestions (
Ypage 35).
34Touchpad
Overview and operation