2016 MERCEDES-BENZ GLC-Class light

XInsert the new bulb into bulb holder;.
XInsert bulb holder;into the groove with
the lug at the top.
XPush bulb holder ;down until it engages
audibly.
XPress on housing cover :and turn it clock-
wise.
Turn signal
XRemove the cover in the front wheel hous-
ing (
Ypage 131).
XTurn bulb holder :counter-clockwise
using the grip under the headlamp casing
and remove it downward with the bulb.
XTurn the bulb counter-clockwise and pull it
out of bulb holder :.
XInsert the new bulb into bulb holder :.
XInsert bulb holder:, turn clockwise and
lock.
XReplace the cover in the front wheel hous-
ing (
Ypage 131).
Replacing rear bulbs (vehicles with
halogen headlamps)
Opening and closing the side trim pan-
els
Example: right-hand side paneling
You must open the side paneling in the cargo
compartment before you can replace the
bulbs in the tail lamps.
XTo open: release right or left side panel-
ing :at the top and fold it down in the
direction of the arrow.
XTo close: insert side paneling :.
Tail lamps
Changing the backup lamp
Due to their location, have the bulbs in the
backup lamp in the tailgate replaced at a
qualified specialist workshop.
XSwitch off the lights.
XOpen the tailgate.
Example: right-hand side handle
132Replacing bulbs
Lights and windshield wipers

XIn recess?on the inside of the closing
handle, pry off and remove the upper sec-
tion of handle =with a flat and smooth
object, e.g. a screwdriver.
XPull the lower section of handle :using a
sharp, sudden movement to remove it from
the paneling and then place it to one side.
XReach under the right-hand side of paneling
B and apply a gentle jolting force along the
entire length of the paneling in order to
unclip it.
XRelease and pull out locator lighting con-
nector Cat the latch.
XVehicles with EASY-PACK tailgate: pull out
the plug connector for the switch of the
EASY-PACK tailgate in the top right of the
paneling.
XVehicles with electric fold-out trailer tow
hitch: unlock and pull out the plug connec-
tor for the electric fold-out trailer tow hitch
in the top left of the paneling.
XPlace paneling Bto one side.
XOn the side where the bulb is to be
changed, unclip the remaining part of pan- eling
Dfrom the assembly using a sudden,
sharp movements, until bulb holder Eis
accessible.
XTurn the bulb counter-clockwise and pull it out of bulb holder E.
XInsert the new bulb into bulb holder Eand
turn it clockwise.
XPosition paneling Dand engage it in place
by tapping it with your hand.
XBefore beginning the installation, check
that all the metal clips are inserted in the
parts placed to one side: 2 clips ;in the
upper part of handle =and 4 clips Ain
paneling B.
XIf not, remove the missing metal clips from
the metal openings in the tailgate and
insert them in the appropriate places.
XTake paneling Band connect plug con-
nector Cto the surround lighting.
iThe surround lighting only illuminates
when the tailgate has been shut and reop-
ened.
XVehicles with EASY-PACK tailgate: push in
the plug connector for the switch of the
EASY-PACK tailgate in the top right of the
paneling.
XVehicles with electric fold-out trailer tow
hitch: push in the plug connector for the
electric fold-out trailer tow hitch in the top
left of the paneling.
XPosition paneling Band engage it in place
by tapping it with your hand, starting from
the outside.
Replacing bulbs133
Lights and windshield wipers
Z

XClip inthe lower section of handle :again.
XInsert and engage the upper section of han-
dle =into lower section :.
Windshield wipers
Switching the windshield wiper
on/off
!
Do not operate the windshield wipers
when the windshield isdry, as this could
damage the wiperblades. Moreover, dust
that has co llected on the windshield can
scratch the glass if wiping takes place when
the windshield is dry.
If it is necessary to switch on the windshield
wiper sin dry weather conditions, always
use washer fluid when operating the wind-
shield wiper s.
!Ifthe windshield wipers leave smears on
the windshield after the vehicle has been
washed inan automat iccar wash, wax or
other residues may bethe reason for this.
Clean the windshield using washer fluid
after washing the vehicle inan automat ic
car wash.
!In term ittent wiping with rain sensor: due
to optical influences and the windshield
becoming dirtyin dry weather conditions,
the windshield wipers may beactivated
inadvertently. This could then damage the
win dshield wiper blades or scratch the
win dshield.
For th isreason, you should always switch
off the windshield wipersin dry weather.
1$ Windshield wiper off
2ÄInterm ittent wipe, low (rain sensor
set to low sensitivit y)
3ÅInterm ittent wipe, high (rain sensor
set to high sensitivit y)
4°Continuous wipe, slow
5¯Continuous wipe, fast
BíSingle wipe
î Towipe with washer fluid
XSwitch on the ignition.
XTurn the combination switch to the corre-
sponding position.
Vehicles with a rain sensor: inthe Ä or
Å position, the appropriate wiping fre-
quency isautomatical lyset according to the
intensity of the rain. Inthe Å position, the
rain sensor ismore sensitive thaninthe Ä
position, causing the windshield wiper to wipe
more frequently.
If the wiper bladesare worn, the windshield
will no longer bewiped properly. This could
prevent you from observing the traff iccond i-
tions.
134Windshield wipers
Lights and windshield wipers

Switching the rear window wiper on/
off
Combination switch
:
èSwitch
2/5bWipes with washer fluid
3ISwitches on intermittent wiping
40 Switches off intermittent wiping
XTurn the SmartKey to position 1or 2in the
ignition lock (
Ypage 153).
XTurn switch :on the combination switch
to the corresponding position.
When the rear window wiper is switched on,
the icon appears in the instrument cluster.
Replacing the wiper blades
Important safety notes
GWARNING
If the windshield wipers begin to move while
you are changing the wiper blades, you could be trapped by the wiper arm. There is a risk of
injury.
Always switch off the windshield wipers and
ignition before changing the wiper blades.
!Never open the hood/tailgate if a wiper
arm has been folded away from the wind-
shield/rear window.
Never fold a windshield wiper arm without a
wiper blade back onto the windshield/rear
window.
Hold the windshield wiper arm firmly when
you change the wiper blade. If you release the wiper arm without a wiper blade and it
falls onto the windshield/rear window, the
windshield/rear window may be damaged
by the force of the impact.
Mercedes-Benz recommends that you have
the wiper blades changed at a qualified
specialist workshop.
!To avoid damaging the wiper blades,
make sure that you touch only the wiper
arm of the wiper.
Changing the windshield wiper blades
Adjusting the wiper blades so that they
are vertical
On vehicles without KEYLESS-GO:
XTurn the SmartKey to position 1or 2in the
ignition lock (
Ypage 153).
XSet the windshield wiper to position °.
XWhen the wiper arms have reached the ver-
tical position, turn the SmartKey to position
0 and remove it from the ignition lock.
XFold the wiper arm away from the wind-
shield.
On vehicles with KEYLESS-GO:
XSwitch off the engine.
XRemove your foot from the brake pedal.
XSet the windshield wiper to the °posi-
tion.
XPress the Start/Stop button repeatedly
until the windshield wiper starts.
XWhen the wiper arms have reached the ver- tical position, press the Start/Stop button.
XFold the wiper arm away from the wind-
shield.
Windshield wipers135
Lights and windshield wipers
Z

Removing the wiper blades
XHold on to the wiper arm with one hand.
With the other hand, turn wiper blade in
direction of arrow:away from the wiper
arm as far as it will go.
XSlide catch ;in the direction of arrow =
until it engages in the removal position with
a noticeable click.
XRemove the wiper blade in the direction of
arrow ?away from the wiper arm.
Installing the wiper blades
XInsert the new wiper blade into the wiper
arm in the direction of arrow :.
XSlide catch;in the direction of arrow =
until it engages in the locking position with a noticeable click.
XMake sure that the wiper blade is seated
correctly.
XFold the wiper arm back onto the wind-
shield.
XRemove protective film :of the service
indicator on the tip of the wiper blade.
If the color of the service indicator changes
from black to yellow, the wiper blades should
be replaced.
iThe duration of the color change varies
depending on the terms of use.
136Windshield wipers
Lights and windshield wipers

Replacing the rear window wiper blades
Removing a wiper blade
XRemove the SmartKey from the ignition
lock.
XFold wiper arm?away from the rear win-
dow.
XPress both release clips ;.
XFold wiper blade:in the direction of
arrow =away from wiper arm ?.
XRemove wiper blade:in the direction of
arrow A.
Installing a wiper blade
XPosition new wiper blade :with recess B
on lug A.
XFold wiper blade :in the direction of
arrow =onto the wiper arm, until retaining
clips ;engage in bracket ?.
XMake sure that wiper blade :is seated
correctly.
XFold the wiper arm back onto the rear win-
dow.
Windshield wipers137
Lights and windshield wipers
Z

Problems with the windshield wipers
ProblemPossible causes/consequences andMSolutions
The windshield wipers
are jammed.Leaves or snow, for example, may be obstructing the windshield
wiper movement. The wiper motor has been deactivated.
XFor safety reasons, you should remove the SmartKey from the
ignition lock.
or
XSwitch off the engine using the Start/Stop button and open the driver's door.
XRemove the cause of the obstruction.
XSwitch the windshield wipers back on.
The windshield wipers
fail completely.The windshield wiper drive is malfunctioning.
XSelect another wiper speed on the combination switch.
XHave the windshield wipers checked at a qualified specialist
workshop.
The windshield washer
fluid from the spray
nozzles no longer hits
the center of the wind-
shield.The spray nozzles are misaligned.
XHave the spray nozzles adjusted at a qualified specialist work-
shop.
138Windshield wipers
Lights and windshield wipers

Control panel for dual-zone automatic climate control
:Sets the temperature, left (Ypage 145)
;Sets the air distribution (Ypage 145)
=Sets the airflow (Ypage 145)
Switches off climate control (
Ypage 142)
?Sets climate control to automatic (Ypage 144)
ADefrosts the windshield (Ypage 146)
BCalls up the Audio 20 or COMAND climate control menu (see the separate operating
instructions)
CSwitches the rear window defroster on or off (Ypage 146)
DActivates or deactivates synchronization (Ypage 145)
ESwitches air-recirculation mode manually on or off (Ypage 147)
FSwitches cooling with air dehumidification on/off (Ypage 142)
GSets the temperature, right (Ypage 145)
Optimum use of dual-zone automatic
climate control
Dual-zone automatic climate control
The following contains notes and recommen-
dations on optimum use of dual-zone climate
control.
RActivate climate control using the Ã
rocker switch. The indicator lamp above
the à rocker switch lights up. The "Cool-
ing with air dehumidification" function is
not activated automatically in automatic mode. If necessary, activate this function
(
Ypage 142).
RSet the temperature to 72 ‡ (22 †).
ROnly use the "Windshield defrosting" func-
tion briefly until the windshield is clear
again.
ROnly use air-recirculation mode briefly, e.g.
if there are unpleasant outside odors or
when in a tunnel. The windows could oth-
erwise fog up, since no fresh air is drawn
into the vehicle in air-recirculation mode.
Overview of climate control systems141
Climate control