2016 MERCEDES-BENZ E-Class WAGON lock

Removing the emergency spare wheel
(Sedan)
(Example: equipment and country-specific varia-
tions possible)
XRemove vehicle tool kit tray:.
XTurn stowage well;counter-clockwise
and remove it.
XRemove "Minispare" emergency spare
wheel =.
Removing the emergency spare wheel
(Wagon)
Example: emergency spare wheel
XRemove vehicle tool kit tray :by
recess ;.
XRemove "Minispare" emergency spare
wheel=.
Removing the emergency spare wheel
(AMG vehicles)
XReach into cutout :in the tool holder and
lift it up.
XRemove collapsible spare wheel ;.
Always observe the instructions and safety
notes in the "Mounting a wheel" section
(
Ypage 309).
Stowing a used collapsible spare
wheel
!
Only place the collapsible spare wheel in
the vehicle when it is dry. Otherwise, mois-
ture may get into the vehicle.
Take the following steps to stow a used col-
lapsible spare wheel. It will not otherwise fit
into the spare wheel well. Mercedes-Benz
recommends that you have this work per-
formed at a qualified specialist workshop, e.g.
at an authorized Mercedes-Benz Center.
XUnscrew the valve cap from the valve.
XUse the back of the valve cap to unscrew
the valve insert from the valve and release
the air.
iFully deflating the tires can take a few
minutes.
XScrew the valve insert back into the valve.
XScrew the valve cap back on.
330Emergency spare wheel
Wheels and tires

XRemove theprotective sheet from th evehi-
cle tool ki tand pull it ove rth ecollapsible
spar ewheel.
XStow th ecollapsible spar ewhee lin th e
emergenc yspar ewhee lwell under th e
trunk/carg ocompartment.
Inflating th ecollapsible spar ewheel
!
Inflat eth ecollapsible spar ewhee lusin g
th etire inflation compressor before lower -
in g th evehicle. The whee lrim could other -
wise be damaged.
!Do no toperate th etire inflation compres-
sor for longer than eigh tminute sat atime
without abreak. It may otherwise overheat .
The tire inflation compressor can be oper -
ate dagain once it has cooled down .
XMountth ecollapsible spar ewhee las
described (
Ypage 309).
The collapsible spar ewhee lmus tbe moun -
te dbefore it is inflated.
XPull connecto r? and th ehos eout of th e
housing.
XRemove th ecap from th evalv eon th ecol-
lapsible spar ewheel.
XScrew union nut :of th ehos eonto th e
valve.
XMak esur eon/off switch Aof th etire
inflation compressor is set to 0.
XInsertconnecto r? into a12 Vsocke t
(
Ypage 251) in your vehicle.
XTurn th eSmartKey to position 1in th eigni-
tion loc k (
Ypage 137).
XPress on/off switch Aon th etire inflation
compressor to I.
The tire inflation compressor is switched
on .The tire is inflated. The tire pressur eis
shown on pressur egauge =.
XInflateth etire to th especified tire pres-
sure.
The specified tire pressur eis printed on th e
yellow label of th eemergenc yspar ewheel.
XWhe nth especified tire pressur ehas been
reached, press on/off switch Aon th e
electric air pump to 0.
The tire inflation compressor is switched
off .
XTurn th eSmartKey to position 0in th eigni-
tion lock.
XIf th etire pressur eis higher than th especi-
fie dpressure, press pressur erel ease va
lv e
butto n; until th ecorrec ttire pressur ehas
been reached.
XUnscrew air hos eunion nut :from th e
valve.
XScrew th ecap onto th evalv eof th ecol-
lapsible spar ewhee lagain .
XStow connecto r? and th ehos ein th e
lower section of th etire inflation compres-
sor .
XStow th etire inflation compressor in th e
vehicle.
Emergency spare wheel331
Wheels and tires
Z

The coolant is a mixture of water and anti-
freeze/corrosion inhibitor. It performs the
following tasks:
Rcorrosion protection
Rantifreeze protection
Rraising the boiling point
If the coolant has antifreeze protection down
to -35 ‡(-37 †), the boiling point of the cool-
ant during operation is approximately 266 ‡
(130 †).
Th ean tifreeze/corrosion inhibitor concentra-
tion in the engine cooling system should:
Rbe at least 50%. This will protect the engine
cooling system against freezing down to
approximately -35‡(-3 7†).
Rno t exceed 55% (antifreeze protection
down to -49‡[-4 5†]) .Otherwise, hea t
will no t be dissipated as effectively.
Mercedes-Benz recommends an antifreeze/
corrosion inhibitor concentrate in accord-
ance with MB Specifications for Service Prod-
ucts 310.1.
iWhen the vehicle is first delivered, it is fil-
led with a coolant mixture that ensures
adequate antifreeze and corrosion protec-
tion.
iThe coolant is checked with every main-
tenance interval at a qualified specialist
workshop.
Filling capacities
ModelCapacity
E 400
E 400 4MATICApprox. 10.9 US qt (10.3l)
E 250 BlueTEC
E 250 BlueTEC
4MATICApprox. 11.0 US qt
(10.4l)
E 63 AMG
E 63 AMG 4MATICApprox. 11.4 US qt
(10.8l)
ModelCapacity
E 550 4MATIC
E 63 AMG S-
MODEL 4MATICApprox. 11.5 US qt
(10.9l)
Allot her modelsApprox. 10.1 US qt
(9.6l)
Windshield washer system
Important safety notes
GWARNING
Windshield washer concentrate could ignite if it comes into contact with hot engine compo-
nents or the exhaust system. There is a risk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the filler neck.
!Do not add distilled or de-ionized water to
the washer fluid container. Otherwise, the
level sensor may be damaged.
!Only MB SummerFit and MB WinterFit
washer fluid should be mixed together. The
spray nozzles may otherwise become
blocked.
Comply with the important safety notes for
service products when handling washer fluid
(
Ypage 337).
At temperatures above freezing:
XFill the washer fluid reservoir with a mixture
of water and windshield washer fluid, e.g.
MB SummerFit.
Add 1 part MB SummerFit to 100 parts water.
At temperatures below freezing:
XFill the washer fluid reservoir with a mixture of water and washer fluid, e.g. MB Winter-
Fit.
For the correct mixing ratio refer to the
information on the antifreeze reservoir.
Service products and filling capacities343
Technical data
Z