2016 MAZDA MODEL CX-9 height adjustment

2–5
Essential Safety Equipment
Seats
Front Seat
Seat Operation

Power operation


Seat Slide
(Manual Seat)
To move a seat forward or backward, raise the lever and slide the seat to the desired position
and release the lever.
Make sure the lever returns to its original position and the seat is locked in place by
attempting to push it forward and backward.
(Power Seat)
To slide the seat, move the slide lifter switch on the outside of the seat to the front or back
and hold it. Release the switch at the desired position.

Height Adjustment (Driver's Seat)
(Manual Seat)
To adjust the seat height, move the lever up or down.
(Power Seat)
To adjust the seat height, move the switch up or down.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










2–8
Essential Safety Equipment
Seats
*Some models.
Driving Position Memory *
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
 
y Driver’s seat position (seat slide, height
adjustment, seat recline)
  Refer to Seat Operation on page 2-5 .


y Active driving display (display position,
brightness level, display information)
 Refer to Active Driving Display on page
4-29 .
 


CAUTION
Do not place fi ngers or hands around
the bottom of the seat while the seat
memory function is operating. The
seat moves automatically while the
seat memory function is operating and
fi ngers or hands could get pinched and
injured.


SET button

The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.

N O T E
 


y Individual seat positions can be
programmed to the two available
programming buttons on the side of the
driver's seat, plus one seat position for
each registered key.
 


y If the vehicle has been serviced and
the battery cables disconnected, the
programmed seat positions will have
been erased. Re-program the seat
positions.

Programming
1. Make sure the parking brake is on.
2. Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings
within 5 seconds of completing step 4
above:
y Programming using a button on
the side of the seat

 Press the button you want to program,
either button 1 or 2, until a beep
sound is heard one time.
y Programming using the key
Press the key
button until a beep
sound is heard one time.

N O T E
If a beep sound is heard three times, the
operation is canceled.

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










2–17
Essential Safety Equipment
Seats
Height Adjustment
Adjust the head restraint so that the center
is even with the top of the passenger's ears.



To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the stop-
catch release, then push the head restraint
down.
Front outboard seat



Second-row outboard seat



Second-row center seat



$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










3–61
Before Driving
Towing
Trailer Hitch
Use only a hitch ball recommended by the trailer manufacturer that conforms to the gross
trailer weight requirement.
When not towing a trailer, remove the trailer hitch (if detachable) to reduce the possibility of
damage as a result of the vehicle being rear-ended.
WARNING
Always make sure the trailer hitch is securely attached before departure:
An unsecured trailer hitch is dangerous as it causes greater trailer sway from crosswinds,
rough roads or other causes, resulting in loss of control and a serious accident.
Examine all trailer-hitch mounting bolts regularly and tighten any that are loose. If the
hitch is removed, seal any open mounting holes to prevent exhaust, dust, water, dirt
and other foreign elements from fi ltering in, possibly endangering personal safety and
damaging your vehicle.
Do not install a hitch that stiff ens the bumper as it will reduce the bumper's performance.

Make sure there are no exhaust gas leaks into the passenger compartment if any
mounting bolts are connected to the body:
Modifying your vehicle exhaust system is dangerous. Exhaust gas entering the vehicle
could cause loss of consciousness or even death.
When mounting the trailer hitch, make no modifi cations to the vehicle exhaust system.

CAUTION
 


¾ Make all hitch adjustments with actual loads. Do not load and unload vehicle while
adjusting hitch. This action will change the vehicle height.
 


¾ Do not use an axle-mounted hitch. This may damage the axle and related parts.
Tires
When towing a trailer, make sure all tires are inÀ ated to the recommended cold-tire pressure,
as indicated on the tire pressure chart on the driver's door frame. Trailer tire size, load rating,
and inÀ ation pressures should conform to tire manufacturer speci¿ cations.
WARNING
Never use the temporary spare tire when towing:
Using the temporary spare tire on your vehicle when towing a trailer is dangerous as it
could result in tire failure, loss of control, and injury to vehicle occupants.

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–30
When Driving
Instrument Cluster and Display
The active driving display indicates the following information:  y Blind Spot Monitoring (BSM) Operation Conditions and Warnings 
 Refer to Blind Spot Monitoring (BSM) on page 4-92 . 



y Distance Recognition Support System (DRSS) Operation Conditions and Warnings
 Refer to Distance Recognition Support System (DRSS) on page 4-98 . 



y Mazda Radar Cruise Control (MRCC) Operation Conditions and Warnings
 Refer to Mazda Radar Cruise Control (MRCC) on page 4-106 . 



y Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Operation
Conditions and Warnings
  Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) on
page 4-117 .




y Smart City Brake Support (SCBS) Warnings
 Refer to Smart City Brake Support (SCBS) on page 4-129 . 



y Smart Brake Support (SBS) Operation Conditions and Warnings
 Refer to Smart Brake Support (SBS) on page 4-134 . 



y Cruise Control Operation Conditions
 Refer to Cruise Control on page 4-147 . 



y Navigation Guidance (vehicles with navigation system) 



y Speed limit indicator (vehicles with navigation system) 



y Tachometer 

y Vehicle Speed
Each setting/adjustment for the active driving display can be performed on the center display.
1. Select the icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
 

y
 Method for adjusting screen brightness (automatically/manually)


y
 Screen brightness initial settings (automatic adjustment is selected)


y
 Screen brightness adjustment (manual adjustment is selected)


y
 Display position of active driving display (display height)y Active driving display angle adjustment (display angle correction)
y
 Turn by turn (TBT) display/non-display (navigation guidance)

y Street name display timing can be changed (navigation guidance) 

y Tachometer display/non-display 


y
 Active driving display ON/OFF (indication)


y
 Reset settings (reset)
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC