2016 MAZDA MODEL CX-9 lock

3–51
Before Driving
Driving Tips
Hazardous Driving
WARNING
Be extremely careful if it is necessary to
downshift on slippery surfaces:
Downshifting into lower gear
while driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid. This
could lead to loss of vehicle control
and an accident.

Avoid sharp turns, excessive speed and
abrupt maneuvers when driving this
vehicle:
Sharp turns, excessive speed and
abrupt maneuvering of this vehicle
are dangerous as it could result in the
increased risk of loss of vehicle control,
vehicle roll-over, personal injury or
death.
This vehicle has a higher center of
gravity. Vehicles with a higher center of
gravity such as utility vehicles handle
diff erently than vehicles with a lower
center of gravity.
Utility vehicles are not designed for
cornering at high speeds any more
than low profi le sports cars are
designed to perform satisfactorily
under off -road conditions.
In addition, utility vehicles have a
signifi cantly higher rollover rate than
other types of vehicles.
In a rollover crash, an unbelted person
is signifi cantly more likely to die than a
person wearing a seat belt.

When driving on ice or in water, snow,
mud, sand, or similar hazards:
 


y Be cautious and allow extra distance for
braking.
 


y Avoid sudden braking and sudden
maneuvering.
 


y Do not pump the brakes. Continue to
press down on the brake pedal.
  Refer to Antilock Brake System (ABS)
on page 4-73 .
 


y If you get stuck, select a lower gear and
accelerate slowly. Do not spin the front
wheels.
 


y For more traction in starting on slippery
surfaces such as ice or packed snow,
use sand, rock salt, chains, carpeting, or
other nonslip material under the front
wheels.

N O T E
Use snow chains only on the front wheels.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










3–54
Before Driving
Driving Tips
Tire Chains
Check local regulations before using tire
chains.
CAUTION
 


¾ Chains may aff ect handling.



¾ Do not go faster than 50 km/h (30
mph) or the chain manufacturer's
recommended limit, whichever is lower.
 


¾ Drive carefully and avoid bumps, holes,
and sharp turns.
 


¾ Avoid locked-wheel braking.



¾ Do not use chains on a temporary spare
tire; it may result in damage to the
vehicle and to the tire.
 


¾ Do not use chains on roads that are free
of snow or ice. The tires and chains could
be damaged.
 


¾ Chains may scratch or chip aluminum
wheels.

N O T E
 
y If your vehicle is equipped with the tire
pressure monitoring system, the system
may not function correctly when using
tire chains.
 

y Use of tire chains on a vehicle equipped
with P255/50R20 speci¿ cation tires
could cause interference with the
vehicle body and scratching. If tire
chains are to be used, replace both front
and rear tires with P255/60R18 tires.
Please consult an Authorized Mazda
Dealer.

Install the chains on the front tires only.
Do not use chains on the rear tires.
Please consult an Authorized Mazda
Dealer.
Installing the chains
1. Secure the chains on the front tires as
tightly as possible.
Always follow the chain manufacturer's
instructions.
2. Retighten the chains after driving
1/2—1 km (1/4—1/2 mile).

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










3–65
Before Driving
Towing
Parking
Always make sure the tires of the trailer and the tow vehicle are blocked while parked.
Apply the parking brake ¿ rmly and put the transaxle in P.
Avoid parking on an incline, but if you must, follow these instructions:
1. Depress and hold down the brake pedal.
2. Have a helper put wheel blocks against the downhill side of all vehicle and trailer tires.
3. Then release the brake pedal slowly until the blocks bear the load.
 

y
 If the grade is downhill, turn the steering wheel so that the front of the front tires face
the curb.
 

y
 If it is uphill, face the rear of the front tires against the curb.
4. Firmly apply the parking brake.
5. Shift the transaxle into P, and stop the engine.

To restart after parking on an incline:
1. With the transaxle in P, start the engine. (Be sure to depress and hold the brake pedal.)
2. Shift into gear.
3. Release the parking brake (also the foot brake) and pull away from the wheel blocks.
Stop; apply the parking brake and shift into P.
4. Have a helper retrieve the wheel blocks.

Fuel consumption
Trailer towing causes higher fuel consumption.
Maintenance
If you tow a trailer frequently, have your vehicle serviced as shown in Scheduled
Maintenance (page 6-4 ).
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–1

*Some models.
4When Driving
Information concerning safe driving and stopping.

Start/Stop Engine ................................ 4-4
Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-10

Instrument Cluster and Display ...... 4-12
Meters and Gauges ....................... 4-12
Multi-information Display and INFO
Switch
* ......................................... 4-21
Active Driving Display * ............... 4-29
Warning/Indicator Lights ............. 4-32

Automatic Transaxle ......................... 4-39
Automatic Transaxle Controls ..... 4-39
Shift-Lock System ....................... 4-40
Transaxle Ranges ......................... 4-41
Manual Shift Mode ...................... 4-43
Driving Tips ................................. 4-48

Switches and Controls ...................... 4-49
Lighting Control ........................... 4-49
Fog Lights
* ................................... 4-55
Turn and Lane-Change Signals .... 4-55
Windshield Wipers and Washer ... 4-56
Rear Window Wiper and
Washer .......................................... 4-60
Rear Window Defogger ............... 4-61
Horn ............................................. 4-62
Hazard Warning Flasher ............... 4-62
HomeLink Wireless Control
System
* ......................................... 4-63
Brake .................................................. 4-67
Brake System ............................... 4-67
Hill Launch Assist (HLA) ............ 4-71

ABS/TCS/DSC/Trailer Stability Assist
(TSA) .................................................. 4-73
Antilock Brake System (ABS) ..... 4-73
Traction Control System (TCS) ... 4-74
Dynamic Stability Control
(DSC) ........................................... 4-76
Trailer Stability Assist (TSA)....... 4-77

Fuel Economy Monitor ..................... 4-78
Fuel Economy Monitor ................ 4-78

Drive Selection ................................... 4-80
Drive Selection ............................. 4-80

i-ACTIV AWD ................................... 4-82
i-ACTIV AWD Operation
* ........... 4-82

Power Steering................................... 4-84
Power Steering ............................. 4-84

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the key is
within operational range.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.

Indicator light

N O T E
 


y The engine starts by pressing the push
button start while depressing the brake
pedal. To switch the ignition position,
press the push button start without
depressing the pedal.
 


y Do not leave the ignition switched ON
while the engine is not running. Doing
so could result in the battery going
dead. If the selector lever is in the P
position, and the ignition is in ACC, the
ignition switches off automatically after
about 25 minutes.

O f f
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat, always
switch the ignition off , set the parking
brake, and make sure the selector lever
is in P:
Leaving the driver's seat without
switching the ignition off , setting the
parking brake, and shifting the selector
lever to P is dangerous. Unexpected
vehicle movement could occur which
could result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off ,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.

ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
N O T E
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–9
When Driving
Start/Stop Engine
If the engine cannot be started due to a
dead key battery, the engine can be started
using the following procedure:

1. Continue to depress the brake pedal
¿ rmly until the engine has completely
started.
2. Verify that the push button start
indication light (green) À ashes.
3. Touch the push button start using the
backside of the key (as shown) while
the push button start indicator light
(green) À ashes.


Transmitter

N O T E
When touching the push button start using
the backside of the key as shown in the
illustration, touch the push button start
with the lock switch side of the key facing
up.

4. Verify that the push button start
indicator light (green) turns on.
5. Press the push button start to start the
engine.
N O T E
 


y The engine cannot be started unless the
brake pedal is fully depressed.
 


y If there is a malfunction with the push
button start function, the push button
start indicator light (amber) À ashes.
In this case, the engine may start,
however, have the vehicle checked at an
Authorized Mazda Dealer as soon as
possible.
 


y If the push button start indicator light
(green) does not illuminate, perform the
operation from the beginning again. If
it does not illuminate, have the vehicle
checked at an Authorized Mazda Dealer.
 


y To switch the ignition position without
starting the engine, perform the
following operations after the push
button start indicator light (green) turns
on.

1. Release the brake pedal.
2. Press the push button start to switch
the ignition position. The ignition
switches in the order of ACC, ON,
and off each time the push button
start is pressed. To switch the
ignition position again, perform the
operation from the beginning.


$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–39
When Driving
Automatic Transaxle
Automatic Transaxle Controls

Lock-release button
Indicates the selector lever can be shifted freely into any position.
Indicates that you must hold in the lock-release button to shift.
Indicates that you must depress the brake pedal and hold in the lock-release
button to shift (The ignition must be switched ON).
Various Lockouts:

N O T E
The Sport AT has an option that is not included in the traditional automatic transaxle that
gives the driver the option of selecting each gear instead of leaving it to the transaxle to
shift gears. Even if you intend to use the automatic transaxle functions as a traditional
automatic, you should also be aware that you can inadvertently shift into manual shift mode
and an inappropriate gear may be retained as the vehicle speed increases. If you notice the
engine speed going higher or hear the engine racing, con¿ rm you have not accidentally
slipped into manual shift mode (page 4-43 ).

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










4–40
When Driving
Automatic Transaxle
Shift-Lock System
The shift-lock system prevents shifting out
of P unless the brake pedal is depressed.

To shift from P:

1. Depress and hold the brake pedal.
2. Start the engine.
3. Press and hold the lock-release button.
4. Move the selector lever.

N O T E
 


y When the ignition is switched to ACC or
the ignition is switched off, the selector
lever cannot be shifted from P.
 


y The ignition cannot be switched to OFF
if the selector lever is not in P.

Shift-Lock Override
If the selector lever will not move from P
using the proper shift procedure, continue
to hold down the brake pedal.

1. Remove the shift-lock override cover
using a cloth-wrapped À at head
screwdriver.
2. Insert a screwdriver and push it down.


Cover

3. Press and hold the lock-release button.
4. Move the selector lever.

Take the vehicle to an Authorized Mazda
Dealer to have the system checked.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC