2016 MAZDA MODEL CX-3 turn signal
[x] Cancel search: turn signalPage 492 of 580
*Some models.7–32
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Illuminate)
Lane Departure
Warning System
(LDWS) Warning
Light
*
y The warning light remains turned on if there is a problem with the system. Have your
vehicle inspected at an Authorized Mazda Dealer.
y The LDWS does not operate when the warning light illuminates.
CAUTION
¾
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an Authorized Mazda Dealer.
¾ When the light remains turned on while driving the vehicle.
When the system is canceled automatically, the light turns on. Normally, the system
restores automatically and the light turns off , however, if the light remains turned on,
there may be a problem with the system.
¾ The light does not illuminate when the ignition is switched ON.
¾
Always use tires for all wheels that are of the specifi ed size, and the same manufacture,
brand, and tread pattern. In addition, do not use tires with signifi cantly diff erent wear
patterns on the same vehicle. If such improper tires are used, the LDWS may not operate
normally.
¾ When an emergency spare tire is used, the system may not operate normally.
(Amber)
High Beam Control
System (HBC)
Warning Light
*
The light remains turned on if there is a problem with the system. Have your vehicle
inspected at an Authorized Mazda Dealer.
NOTE
If the windshield area in front of the Forward Sensing Camera (FSC) is fogged or
obstructed, the light turns on temporarily. If the light remains turned on, there may be a
problem with the system.
LED Headlight
Warning Light *
This light illuminates if there is a malfunction in the LED headlight. Have your vehicle
inspected by an Authorized Mazda Dealer.
(Amber)
Mazda Radar
Cruise Control
(MRCC) Warning
Light
*
The warning light turns on if there is a malfunction in the system while the Mazda Radar
Cruise Control (MRCC) system is on.
Have your vehicle inspected at an Authorized Mazda Dealer.
Blind Spot
Monitoring (BSM)
OFF Indicator
Light
*
A problem in the system may be indicated under the following conditions.
Have your vehicle inspected at an Authorized Mazda Dealer.
y The light does not turn on when the ignition is switched ON. y The light remains turned on even if the Blind Spot Monitoring (BSM) switch is operated. y It turns on while driving the vehicle.
NOTE
If the vehicle is driven on a road with less traffi c and few vehicles that the radar sensors
can detect, the system may pause (The Blind Spot Monitoring (BSM) OFF indicator light in
the instrument cluster illuminates). However, it does not indicate a malfunction.
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C
Page 493 of 580
7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Taking Action
Take the appropriate action and verify that the warning light turns off.
Signal Warning Action to be taken
Low Fuel Warning
Light The light turns on when the remaining fuel is
about 9.0 L (2.3 US gal, 1.9 Imp gal). NOTE
The light illumination timing may vary because
fuel inside the fuel tank moves around according
to the driving conditions and the vehicle posture. Add fuel.
Check Fuel Cap
Warning Light If the check fuel cap warning light illuminates
while driving, the fuel-fi ller cap may not be
installed properly. Stop the engine and reinstall the fuel-
fi ller cap.
Refer to Fuel-Filler Cap on page 3-26
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C
Page 494 of 580
*Some models.7–34
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
Seat Belt Warning
Light
Except Mexico
The seat belt warning light turns on if the driver
or front passenger's seat is occupied and the seat
belt is not fastened with the ignition switched
ON.
If the driver or front passenger's seat belt is
unfastened (only when the front passenger's seat
is occupied) and the vehicle is driven at a speed
faster than about 20 km/h (12 mph), the warning
light fl ashes. After a short time, the warning
light stops fl ashing, but remains illuminated.
NOTE
yThe warning light fl ashes for about 6 seconds
if the driver's seat belt is not fastened when the
ignition is switched ON.
yTo allow the front passenger occupant
classifi cation sensor to function properly, do
not place and sit on an additional seat cushion
on the front passenger's seat. The sensor may
not function properly because the additional
seat cushion could cause sensor interference.
yIf a small child is seated on the front
passenger's seat, the warning light may not
operate.
Mexico
The seat belt warning light turns on if the driver
or front passenger's seat is occupied and the seat
belt is not fastened with the ignition switched
ON.
If the driver or front passenger's seat belt is
unfastened (only when the front passenger's seat
is occupied) and the vehicle is driven at a speed
faster than about 20 km/h (12 mph), the warning
light fl ashes. After a short time, the warning
light stops fl ashing, but remains illuminated. If
a seat belt remains unfastened, the warning light
fl ashes again for a given period of time.
NOTE
yPlacing heavy items on the front passenger's
seat may cause the front passenger's seat belt
warning function to operate depending on the
weight of the item.
yTo allow the front passenger seat weight
sensor to function properly, do not place and
sit on an additional seat cushion on the front
passenger's seat. The sensor may not function
properly because the additional seat cushion
could cause sensor interference.
yIf a small child is seated on the front
passenger's seat, the warning light may not
operate. Fasten the seat belts.
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C
Page 495 of 580
*Some models.7–35
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
Door-Ajar Warning Light The light turns on if any door is not closed
securely.
Close the door securely.
Low Washer Fluid
Level Warning Light
*
This warning light indicates that little washer
fl uid remains. Add washer fl
uid (page 6-32 ).
(Illuminate)
Tire Pressure
Monitoring System Warning Light
*
When the warning light illuminates, and the
warning beep sound is heard (about 3 seconds),
tire pressure is too low in one or more tires.
WARNING
If the tire pressure monitoring system
warning light illuminates or fl ashes, or the
tire pressure warning beep sound is heard,
decrease vehicle speed immediately and
avoid sudden maneuvering and braking: If the tire pressure monitoring system
warning light illuminates or fl ashes, or the
tire pressure warning beep sound is heard,
it is dangerous to drive the vehicle at high
speeds, or perform sudden maneuvering
or braking. Vehicle drivability could worsen
and result in an accident.
To determine if you have a slow leak or a
fl at, pull over to a safe position where you
can check the visual condition of the tire
and determine if you have enough air to
proceed to a place where air may be added
and the system monitored again by an
Authorized Mazda Dealer or a tire repair
station.
Do not ignore the TPMS Warning Light: Ignoring the TPMS warning light is
dangerous, even if you know why it is
illuminated. Have the problem taken care of
as soon as possible before it develops into
a more serious situation that could lead to
tire failure and a dangerous accident. Inspect the tires and adjust to the
specifi
ed infl ation pressure (page 6-42 ).
NOTE
yPerform tire pressure adjustment when
the tires are cold. Tire pressure will
vary according to the tire temperature,
therefore let the vehicle stand for 1
hour or only drive it 1.6 km (1 mile) or
less before adjusting the tire pressures.
When pressure is adjusted on hot tires
to the cold infl ation pressure, the TPMS
warning light/beep may turn on after
the tires cool and pressure drops below
specifi cation.
Also, an illuminated TPMS warning
light, resulting from the tire air
pressure dropping due to cold ambient
temperature will remain illuminated
even if the ambient temperature rises.
In this case, it will also be necessary
to adjust the tire air pressures. If the
TPMS warning light illuminates due to
a drop in tire air pressure, make sure to
check and adjust the tire air pressures.
yTires lose air naturally over time and the TPMS cannot tell if the tires are
getting too soft over time or you have
a fl at. However, when you fi nd one low
tire in a set of four-that is an indication
of trouble; you should have someone
drive the vehicle slowly forward so
you can inspect any low tire for cuts
and any metal objects sticking through
tread or sidewall. Put a few drops
of water in the valve stem to see if it
bubbles indicating a bad valve. Leaks
need to be addressed by more than
simply reinfl ating the tire as leaks are
dangerous — take it to an Authorized
Mazda Dealer.
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C
Page 496 of 580
*Some models.7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
(Amber)
Smart Brake
Support/Smart
City Brake Support (SBS/SCBS)
Warning Light
*
The light turns on if the windshield or the radar
sensor are dirty, or there is a malfunction in the
system.
(Vehicles with type B audio)
Verify the reason why the warning light
is illuminated on the center display (page
7-27 ).
If the reason why the warning light is
illuminated is due to a dirty windshield,
clean the windshield.
If the warning light is illuminated
because of a dirty radar sensor, clean the
front emblem.
For any other reasons, have the vehicle
inspected at an Authorized Mazda Dealer.
(Vehicles without type B audio)
If the reason why the warning light is
illuminated is due to a dirty windshield,
clean the windshield. For any other
reasons, have the vehicle inspected at an
Authorized Mazda Dealer.
KEY Warning Light
Take the appropriate action and verify that the warning light turns off.
Signal Cause Action to be taken
(Red)
(Flashing) The advanced key battery is dead. Replace the key battery (page 6-39 ).
The advanced key is not within the
operation range.
Bring the advanced key into the operation
range (page 3-7 ).
The advanced key is placed in areas inside
the cabin where it is diffi
cult for the key to
be detected.
A key from another manufacturer similar to
the advanced key is in the operation range. Take the key from another manufacturer
similar to the advanced key out of the
operation range.
Without the ignition switched off, the
advanced key is taken out of the cabin, and
then all the doors are closed. Bring the advanced key back into the
cabin.
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C
Page 502 of 580
*Some models.7–42
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Blind Spot Monitoring (BSM)
System Warning Beep *
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the Blind Spot Monitoring (BSM) warning
light is illuminated.
NOTE
A personalized function is available to
change the Blind Spot Monitoring (BSM)
warning beep sound volume.
Refer to Personalization Features on page
9-10 .
Reversing
If a moving object such as a vehicle or
two-wheeled vehicle approaches on the
left or right from behind your vehicle, the
Blind Spot Monitoring (BSM) warning
sound is activated.
Lane Departure Warning System
(LDWS) Warning Sound *
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound.
NOTE
y The volume of the LDWS warning sound
can be changed.
Refer to Personalization Features on
page 9-10 .
y The type of the LDWS warning sound
can be changed.
Refer to Personalization Features on
page 9-10 .
Mazda Radar Cruise Control
(MRCC) System Warnings *
The Mazda Radar Cruise Control (MRCC)
system warnings notify the driver of
system malfunctions and cautions on use
when required.
Check based on the beep sound.
Cautions What to check
The beep sounds 1 time
while the Mazda Radar
Cruise Control (MRCC)
is operating The vehicle speed is
slower than 25 km/h (16
mph) and the Mazda
Radar Cruise Control
(MRCC) system has
been canceled.
The beep sounds
continuously while
driving The distance between
your vehicle and the
vehicle ahead is too
close. Verify the safety
of the surrounding area
and reduce vehicle
speed.
When the Mazda Radar
Cruise Control (MRCC)
is operating, the beep
sounds and the Mazda
Radar Cruise Control
(MRCC) warning
light (amber) in the
instrument cluster turns
on. A malfunction in
the system may be
indicated. Have your
vehicle inspected at
an Authorized Mazda
Dealer.
Collision warning *
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the display.
Power Steering Warning Buzzer
If the power steering system has
a malfunction, the power steering
malfunction light turns on or fl ashes and
the buzzer operates at the same time.
Refer to Warning/Indicator Lights on page
4-24 .
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C
Page 563 of 580
*Some models.9–7
Specifi cations
Specifi cations
Light Bulbs
Exterior light
Light bulb Category
Wattage UNECE *1 (SAE)
Headlights Halogen headlights
High beam 65 HB3 (9005)
Low beam 55 H11 (H11)
LED headlights High beam LED
*2 — (—)
Low beam LED *2 — (—)
Daytime running lights With halogen headlights 65 HB3 (9005)
With LED headlights LED
*2 — (—)
Front side-maker lights/Parking lights With halogen headlights 5 W5W (—)
With LED headlights LED
*2 — (—)
Front turn signal lights U.S.A. and Canada 27 — (1156NA)
Mexico 21 PY21W (—)
Fog lights
* LED *2 — (—)
Side turn signal lights * LED *2 — (—)
High-mount brake light LED *2 — (—)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-maker lights With halogen headlights 5 W5W (—)
With LED headlights LED
*2 — (—)
Brake lights/Taillights With halogen headlights 21/5 W21/5W (7443)
With LED headlights LED
*2 — (—)
Taillights (With LED headlights) LED *2 — (—)
Reverse lights 18 W16W (921)
License plate lights 5 W5W (—)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulb Category
Wattage UNECE *1
Overhead light (Front)/Map lights 8 —
Overhead light (Rear) 10 —
Luggage compartment light 5 —
*1 UNECE stands for United Nations Economic Commission for Europe.
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C
Page 571 of 580
9–15
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings change method
Vehicle Leaving home
light system
Refer to
Leaving Home
Light System
on page 4-45 . The leaving home light
system function can be
changed. On On/Off
Refer to
Settings
on page
5-53 . —
Turn indicator
Refer to Turn
and Lane-
Change Signals
on page 4-46 . The turn indicator beep
volume level can be
changed. High High/Low Refer to
Settings
on page
5-53 . —
Three-fl ash turn
signal
Refer to Three-
Flash Turn
Signal on page
4-47 . The three-fl ash turn
function can be
changed. On On/Off
Refer to
Settings
on page
5-53 . —
System Distance unit The distance unit can be
changed. mi or km mi/km
Refer to
Settings
on page
5-53 . —
Language The display language
can be changed. *8 English English/
French/
Spanish Refer to
Settings
on page
5-53 . —
Temperature
unit The temperature unit
can be changed. °F or °C °F/°C Refer to
Settings
on page
5-53 . —
Fuel
Economy
Monitor
Refer
to Fuel
Economy
Monitor
on page
4-62 . Ending display Setting can be changed
so that the ending
display of the Fuel
Economy Monitor is
displayed. Off On/Off
Refer
to Fuel
Economy
Monitor
on page
4-62 . —
Fuel economy
resetting
procedure Setting can be changed
so that the fuel economy
reset is linked with the
trip meter reset. Off On/Off Refer
to Fuel
Economy
Monitor
on page
4-62 . —
$ 9 @ & ) & " # @ & E J U J P O J O E C $ 9 @ & ) & " # @ & E J U J P O J O E C