2016 MAZDA MODEL CX-3 headlights

6–47
Maintenance and Care
Owner Maintenance
WARNING
Never touch the glass portion of a
halogen bulb with your bare hands
and always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it will
explode and serious injuries could be
caused by the fl ying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.

Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
CAUTION
When removing the lens or lamp unit
using a fl athead screwdriver, make
sure that the fl athead screwdriver does
not contact the interior terminal. If
the fl athead screwdriver contacts the
terminal, a short circuit may occur.
NOTE
 


y To replace the bulb, contact an
Authorized Mazda Dealer.
 


y If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
 


y Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
Replacing Exterior Light Bulbs
Headlights (With LED headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Headlights/Daytime running lights
(With halogen headlights)
High-beams bulbs/Daytime running
lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your fi nger and pulling the
connector downward.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










6–48
Maintenance and Care
Owner Maintenance
4. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the refl ector by
gently pulling it straight backward out
of the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
Low-beam bulbs
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your fi nger and pulling the
connector downward.
4. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the refl ector by
gently pulling it straight backward out
of the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
Daytime running lights/Parking lights/
Front side-marker lights (With LED
headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.6–49
Maintenance and Care
Owner Maintenance
Front side-marker lights/Parking lights
(With halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of the removal procedure.
Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
Fog lights
* , Side turn signal lights * ,
Brake lights/Taillights (With LED
headlights), Rear side-marker lights
(With LED headlights),Taillights (With
LED headlights), High-mount brake
light
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










6–50
Maintenance and Care
Owner Maintenance
Rear turn signal lights, Brake lights/
Taillights (With halogen headlights),
Rear side-marker lights (With halogen
headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the bolts counterclockwise and
remove them.
3. Pull the unit rearward to remove it.
4. Turn the socket and bulb assembly
counterclockwise and remove it. 5. Disconnect the bulb from the socket.
Rear turn signal lights
Brake lights/Taillights
Rear side-marker lights
6. Install the new bulb in the reverse order
of the removal procedure.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










6–54
Maintenance and Care
Owner Maintenance
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is
blown, replace it with a new oneof the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse and
multiplex slow blow fuse by yourself.
Have an Authorized Mazda Dealer
perform the replacement:
Replacing these fuses by yourself is
dangerous because they are high
current fuses. Incorrect replacement
could cause an electrical shock or a
short circuit resulting in a fi re.
4. Reinstall the cover and make sure that
it is securely installed.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.9–7
Specifi cations
Specifi cations
Light Bulbs
Exterior light
Light bulb Category
Wattage UNECE *1 (SAE)
Headlights Halogen headlights
High beam 65 HB3 (9005)
Low beam 55 H11 (H11)
LED headlights High beam LED
*2 — (—)
Low beam LED *2 — (—)
Daytime running lights With halogen headlights 65 HB3 (9005)
With LED headlights LED
*2 — (—)
Front side-maker lights/Parking lights With halogen headlights 5 W5W (—)
With LED headlights LED
*2 — (—)
Front turn signal lights U.S.A. and Canada 27 — (1156NA)
Mexico 21 PY21W (—)
Fog lights
* LED *2 — (—)
Side turn signal lights * LED *2 — (—)
High-mount brake light LED *2 — (—)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-maker lights With halogen headlights 5 W5W (—)
With LED headlights LED
*2 — (—)
Brake lights/Taillights With halogen headlights 21/5 W21/5W (7443)
With LED headlights LED
*2 — (—)
Taillights (With LED headlights) LED *2 — (—)
Reverse lights 18 W16W (921)
License plate lights 5 W5W (—)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulb Category
Wattage UNECE *1
Overhead light (Front)/Map lights 8 —
Overhead light (Rear) 10 —
Luggage compartment light 5 —
*1 UNECE stands for United Nations Economic Commission for Europe.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










9–14
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings change method
Vehicle Auto-wiper
control
Refer to
Windshield
Wipers and
Washer on page
4-47 . The auto-wiper control
function can be
changed. On On/Off
*4 Refer to
Settings
on page
5-53 . —
Daytime
running lights
Refer to
Daytime
Running Lights
on page 4-45 . The function of the
daytime running lights
can be changed. On On/
Off
Refer to
Settings
on page
5-53 . —
Auto headlight
off *5
Refer to
Headlights on
page 4-41 . The time required
for headlights to turn
off after ignition is
switched off can be
changed. 30 seconds
120 seconds/ 90 seconds/
60 seconds/
30 seconds/
Off
*6
Refer to
Settings
on page
5-53 . —
Auto-light
control
Refer to
Headlights on
page 4-41 . The headlight
illumination on/
off timing based on
surrounding lightness/
darkness can be
changed. Medium High/
Med. High/
Medium/
Med. Low/
Low Refer to
Settings
on page
5-53 . —
High Beam
Control System
(HBC)
Refer to High
Beam Control
System (HBC)
on page 4-71 . The High Beam Control
System (HBC) function
can be changed.
*1 On On/Off Refer to
Settings
on page
5-53 . —
Adaptive
Front Lighting
System (AFS)
Refer to
Adaptive
Front Lighting
System (AFS)
on page 4-70 . The Adaptive Front
Lighting System
(AFS) function can be
changed.
*1
On On/Off Refer to
Settings
on page
5-53 . —
Lights-on
reminder*7
Refer to Lights-
On Reminder
on page 7-39 . The volume of the
lights-on reminder
warning alarm can be
changed. Off High/Low/
Off Refer to
Settings
on page
5-53 . —
Coming home
light system
Refer to
Coming Home
Light System
on page 4-44 . The time required for
the headlights to turn
off after closing all
of the doors can be
changed. 30 seconds 120 seconds/ 90 seconds/
60 seconds/
30 seconds/
Off Refer to
Settings
on page
5-53 . —
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










9–16
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings change method
Active
driving
display
Refer to
Active
Driving
Display
on page
4-22 . Turn-by-Turn
(TBT) Setting can be changed
so that the Turn-by-Turn
(TBT) of the Active
driving display is not
displayed. On On/Off
Refer to
Active
driving
display
on page
4-22 . —
*1 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda recommends
that these systems remain On.
*2 For vehicles with an audio system other than the on-screen function type, the warning sound cannot be changed.
The warning sound is only a beep.
*3 Only the volume of the warning beep during Blind Spot Monitoring (BSM) operation can be changed. The
volume of the warning beep during Rear Cross Traffi c Alert (RCTA) operation cannot be changed.
*4 If the auto-wiper control is set to Off, the wiper lever
position is set to intermittent operation.
*5 If the setting is changed to Off, the following operation is performed according to the headlight switch position:
y At position: Headlights turn off immediately after the ignition is switched off.y At any position other than : Headlights do not turn off after the ignition is switched off.
*6 When set to Off, the lights-on reminder is operable.
*7 The setting of the lights-on reminder can be changed with the time setting of auto headlight off function set to
Off. Refer to Lights-On Reminder on page 7-39 .
*8 Available only in display from the center display.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC