2016 MAZDA MODEL CX-3 high beam

4–72
When Driving
i-ACTIVSENSE
NOTE
The timing in which the system switches the headlights changes under the\
following
conditions. If the system does not switch the headlights appropriately, manually switch
between high and low beams according to the visibility as well as road and traffi c
conditions.
 y When there are sources of light in the area such as street lamps, illuminated signboards,
and traffi c signals.

y When there are refl ective objects in the surrounding area such as refl ective plates and
signs.

y  When visibility is reduced under rain, snow and foggy conditions.
y When driving on roads with sharp turn or hilly terrain.
y When the headlights/rear lamps of vehicles in front of you or in the opposite lane are dim
or not illuminated.

y When there is suffi cient darkness such as at dawn or dusk.
y When the luggage compartment is loaded with heavy objects or the rear passenger seats
are occupied.

y When visibility is reduced due to a vehicle in front of you spraying water from its tires
onto your windshield.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–73
When Driving
i-ACTIVSENSE
To Operate the System
The High Beam Control System (HBC)
operates to switch the headlights
automatically between high and low
beams after the ignition is switched ON
and the headlight switch is in the AUTO
and high beam position.
The High Beam Control System (HBC)
determines that it is dark based on the
brightness of the surrounding area. At the
same time, the High Beam Control System
(HBC) indicator light (green) in the
instrument cluster illuminates.
NOTE
 y When the vehicle speed is 30 km/h
(18 mph) or higher, the headlights
automatically switch to high beams
when there are no vehicles ahead or
approaching in the opposite direction.
 When the vehicle speed is less than about 20 km/h (12 mph), the High Beam
Control System (HBC) switches the
headlights to low beams.
 y The low beams may not switch to high
beams when cornering.

y Operation of the High Beam Control
System (HBC) function can be disabled.
Refer to Personalization Features on
page 9-10 .
Manual Switching
Switching to low beams
Shift the lever to the low beam position.
The High Beam Control System (HBC)
indicator light (green) turns off.
Switching to high beams
Turn the headlight switch to the
position.
The High Beam Control System (HBC)
indicator light (green) turns off and the
is illuminated.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–106
When Driving
i-ACTIVSENSE
CAUTION
 


¾ When driving off -road in areas where there is grass or forage, it is recommended that the
Smart City Brake Support (SCBS) system be turned off .




¾ Always use tires for all wheels that are of the specifi ed size, and the same manufacturer,
brand, and tread pattern. In addition, do not use tires with signifi cantly diff erent wear
patterns on the same vehicle as the Smart City Brake Support (SCBS) system may not
operate normally.
 


¾ The laser sensor (front) includes a function for detecting a soiled windshield and informing
the driver, however, depending on the conditions, it may not detect plastic shopping bags,
ice or snow on the windshield. In such cases, the system cannot accurately determine a
vehicle ahead and may not be able to operate normally. Always drive carefully and pay
attention to the road ahead.
NOTE
 


y The Smart City Brake Support (SCBS) system will not operate if the driver is deliberately
performing driving operations (accelerator pedal and steering wheel).
 


y The Smart City Brake Support (SCBS) system will operate under the following conditions.




y The engine is running.



y The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.



y The vehicle speed is between about 4 to 30 km/h (2 to 18 mph).



y The Smart City Brake Support (SCBS) system is not turned off.



y The DSC is not malfunctioning.




y The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-infrared
laser beam and receiving the beam refl ected off the refl ector of the vehicle ahead, and
then using it for the measurement. Consequently, the Smart City Brake Support (SCBS)
may not operate under the following conditions:
 


y Refl ection of the laser is poor due to the shape of the vehicle ahead.



y The vehicle ahead is signifi cantly dirty.



y Under bad weather condition, such as rain, fog and snow.



y The window washer is being used or the windshield wipers are not used when it's
raining.
 


y The windshield is dirty.



y The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


y Trucks with low loading platforms and vehicles with an extremely low or high profi le.



y Vehicles with certain shapes such as a vehicle carrier.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.4–112
When Driving
i-ACTIVSENSE
Forward Sensing Camera (FSC) *
Your vehicle is equipped with a Forward Sensing Camera (FSC). The Forward Sensing
Camera (FSC) is positioned near the rearview mirror and used by the following systems.
 


y High Beam Control System (HBC)



y Lane Departure Warning System (LDWS)



y Smart Brake Support (SBS)
Forward Sensing Camera (FSC)
The Forward Sensing Camera (FSC) determines the conditions ahead of the vehicle while
traveling at night and detects traffi c lanes. The distance in which the Forward Sensing
Camera (FSC) can detect objects varies depending on the surrounding conditions.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–113
When Driving
i-ACTIVSENSE
CAUTION
 


¾ Do not apply accessories, stickers or fi lm to the windshield near the Forward Sensing
Camera (FSC).
  If the area in front of the Forward Sensing Camera (FSC) lens is obstructed, it will cause
the system to not operate correctly. Consequently, each system may not operate normally
which could lead to an unexpected accident.
 


¾ Do not disassemble or modify the Forward Sensing Camera (FSC).
 Disassembly or modifi cation of the Forward Sensing Camera (FSC) will cause a malfunction
or mistaken operation. Consequently, each system may not operate normally which could
lead to an unexpected accident.
 


¾ Heed the following cautions to assure the correct operation of the Forward Sensing Camera
(FSC).
 


¾ The direction of the Forward Sensing Camera (FSC) has been fi nely adjusted, therefore
do not change the installation position or remove the Forward Sensing Camera (FSC).
 


¾ Be careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get dirty.



¾ Do not remove the Forward Sensing Camera (FSC) cover.



¾ Do not place objects on the dashboard which refl ect light.



¾ Always keep the windshield glass around the camera clean by removing dirt or fogging.
Use the windshield defroster to remove fogging on the windshield.
 


¾ Consult an Authorized Mazda Dealer regarding cleaning the interior side of the
windshield around the Forward Sensing Camera (FSC).
 


¾ Consult an Authorized Mazda Dealer before performing repairs around the Forward
Sensing Camera (FSC).
 


¾ The Forward Sensing Camera (FSC) is installed to the windshield. Consult an Authorized
Mazda Dealer for windshield repair and replacement.
 


¾ When performing repairs around the rearview mirror, consult an Authorized Mazda
Dealer.
 


¾ Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area around
it. If strong force is applied, stop using the Lane Departure Warning System (LDWS), the
High Beam Control System (HBC), and the Smart Brake Support (SBS) and consult an
Authorized Mazda Dealer.
 


¾ The direction in which the Forward Sensing Camera (FSC) is pointed has been fi nely
adjusted. Do not change the installation position of the Forward Sensing Camera (FSC)
or remove it. Otherwise, it could result in damage or malfunction.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–114
When Driving
i-ACTIVSENSE
NOTE
 


y In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
 


y The height of the vehicle ahead is low.



y You drive your vehicle at the same speed as the vehicle ahead.



y Headlights are not turned on during the night or when going through a tunnel.




y In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
 


y When driving next to walls with no patterning (including fences and longitudinally
striped walls).
 


y The taillights of the vehicle ahead are turned off.



y A vehicle is outside the illumination range of the headlights.



y The vehicle is making a sharp curve, or ascending or descending a steep slope.



y Entering or exiting a tunnel.



y Heavy luggage is loaded causing the vehicle to tilt.



y Strong light is shone at the front of the vehicle (back light or high-beam light from on-
coming vehicles).
 


y There are many light emitters on the vehicle ahead.



y When the vehicle ahead is not equipped with taillights or the taillights are turned off at
nighttime.
 


y The vehicle ahead has a special shape.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–132
When Driving
Rear View Monitor
Displayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)Garnish
Bumper
(Actual view)
Object
NOTE

y The displayable range varies depending on the vehicle and road conditions.
y The displayable range is limited. Objects under the bumper or around the bumper ends
cannot be displayed.

y The distance appearing in the displayed image is different from the actual distance
because the rear view parking camera is equipped with a specifi c lens.

y Some optionally installed vehicle accessories may be picked up by the ca\
mera. Do not
install any optional parts that can interfere with the camera view, such as illuminating
parts or parts made of refl ective material.
 y It may be diffi cult to see the display under the following conditions, however, it does not
indicate a malfunction.

y In darkened areas.
y When the temperature around the lens is high/low.
y When the camera is wet such as on a rainy day or during periods of high \
humidity.
y When foreign material such as mud is stuck around the camera.
y When the camera lens refl ects sunlight or headlight beams.

y Image display may be delayed if the temperature around the camera is low.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










5–15
Interior Features
Audio System
Do not spill any liquid on the audio
system.
Do not insert any objects, other than CDs,
into the slot.
Radio Reception
AM characteristics
AM signals bend around such things as
buildings or mountains and bounce off the
ionosphere.
Therefore, they can reach longer distances
than FM signals.
Because of this, two stations may
sometimes be picked up on the same
frequency at the same time.
Station 2 Station 1Ionosphere
FM characteristics
An FM broadcast range is usually about
40—50 km (25—30 miles) from the
source. Because of extra coding needed to
break the sound into two channels, stereo
FM has even less range than monaural
(non-stereo) FM.
FM Station
40—50km
(25—30 miles)
Signals from an FM transmitter are similar
to beams of light because they do not
bend around corners, but they do refl ect.
Unlike AM signals, FM signals cannot
travel beyond the horizon. Therefore, FM
stations cannot be received at the great
distances possible with AM reception.
AM wave FM wave
FM wave
100—200 km (60—120 miles)Ionosphere
Atmospheric conditions can also affect
FM reception. High humidity will cause
poor reception. However, cloudy days may
provide better reception than clear days.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC