2016 MAZDA MODEL 3 HATCHBACK heating

30
NOTE: A/C indicator
will illuminate when
AUTO ON is active.
The air conditioning
cycles on/off as
necessary to maintain
the set temperature.
The A /C may operate
even while heating
is desired - this is
to prevent excess
humidity and
fogging while the
system operates.
Automatic Climate Control
DRIVER TEMPERATURE
CONTROL DIAL
Push to defrost
the rear window.PASSENGER
TEMPERATURE
CONTROL DIAL
Push to turn DUAL
mode ON/OFF.
• With DUAL mode ON (indicator on),
rotate the dial to
set passenger
side temperature
separate from
the driver’s side
(shown above).
• With DUAL mode
OFF (indicator off),
driver controls the
temperature setting
on both sides.
Push to select the
following airflow mode:
Dashboard vents
Dashboard
and floor vents
Floor vents
Defroster and
floor vents
Push to defrost
the windshield.
Push to
manually turn
air conditioning
on or off.
NOTE: Automatic
temperature control
always works even
if the AUTO indicator
turns off by changing
the fan speed or
airflow mode.
Fan Control
• Push the fan (+) and (-)
buttons to select the
desired fan speed.
• Push OFF to turn climate
control system off.
Push to recirculate
cabin air to reduce
outside odors and
improve cooling.
Push for fresh
air circulation.
AUTO ON: Push dial
to turn automatic air
conditioning system
on (AUTO ON and A /C
indicator on). The airflow
mode, fan speed and
air conditioning will be
automatically controlled
in accordance with the
set temperature.
2032271_16a_Mazda3_SSG_051215.indd 305/12/15 11:51 AM
www.MazdaUSA.com

32
1 • Rotate the knob to adjust the brightness of the instrument cluster and o\
ther dashboard illuminations.2 • Push to toggle between trip meter (A & B).
• When a trip meter is selected, push and hold to reset to zero.
3 • Push the knob for 1.5 seconds or more to change the speed units between km/h and mph.
Brake Warning Light
Parking brake on/low brake
fluid/malfunction
Master Warning Light
Low Fuel Level
Low Engine Oil Pressure
Power Steering Malfunction
Automatic Transaxle

Warning Light
Charging System
Malfunction
Door/Trunk/Tailgate Ajar
Low Washer Fluid Level
Warning Light
KEY Warning Light RED
KEY Indicator Light GREEN
Check Fuel Cap
Perform Maintenance
i-ELOOP Status (p. 34 )

On : Power generation
Flashing : Pre-Charge Mode
DASHBOARD ILLUMINATION/
DIMMER1/TRIP METER2
ENGINE COOLANT TEMP LIGHTS
Since this vehicle does not use an engine
coolant temperature gauge, red and blue
engine coolant temperature lights are used to
indicate high and low coolant temperature.
Red Coolant Temp Light
Flashing: Engine is starting to run hot.
Drive slowly to reduce engine load.
On: Engine is overheating. Safely pull
over to the side of the road and turn
the engine off. Refer to the Owner’s
Manual for more information.
Blue Coolant Temp Light
On: Engine coolant is cold and no warm
air is available for heater/defroster.
Off: Engine coolant is warm and
warm air is available for heater/
defroster. The light may stay on for a
few minutes after start-up when the
engine is cold, but the vehicle can
be driven with the light on or off.
I M P O R TA N T: When your
Mazda Connect display
setting is set on “AUTO”, the
instrument cluster and display
may become dimmer when the
headlights are on. If the display
and instrument cluster become
too dim or too bright when the
headlights are on, simply rotate
the dimmer knob located on
your instrument cluster to
adjust the brightness.
2032271_16a_Mazda3_SSG_051215.indd 325/12/15 11:51 AM
www.MazdaUSA.com

34
DASHBOARD ILLUMINATION/
DIMMER1/TRIP METER2
1 • Rotate the knob to adjust the brightness of the instrument cluster and o\
ther dashboard illuminations.2 • Push to toggle between trip meter (A & B).
• When a trip meter is selected, push and hold to reset to zero.
Master Warning Light
Low Fuel Level
Low Engine Oil Pressure
Power Steering Malfunction
Automatic Transaxle

Warning Light
Charging System
Malfunction
Door/Trunk/Tailgate Ajar
Low Washer Fluid Level
Warning Light
KEY Warning Light RED
KEY Indicator Light GREEN
Check Fuel Cap
Perform Maintenance
ENGINE COOLANT TEMP LIGHTS

Since this vehicle does not use an engine
coolant temperature gauge, red and blue
engine coolant temperature lights are used to
indicate high and low coolant temperature.
Red Coolant Temp Light
Flashing: Engine is starting to run hot.
Drive slowly to reduce engine load.
On: Engine is overheating. Safely pull
over to the side of the road and turn
the engine off. Refer to the Owner’s
Manual for more information.
Blue Coolant Temp Light
On: Engine coolant is cold and no warm
air is available for heater/defroster.
Off: Engine coolant is warm and
warm air is available for heater/
defroster. The light may stay on for a
few minutes after start-up when the
engine is cold, but the vehicle can
be driven with the light on or off.
I M P O R TA N T: When your
Mazda Connect display
setting is set on “AUTO”, the
instrument cluster and display
may become dimmer when the
headlights are on. If the display
and instrument cluster become
too dim or too bright when the
headlights are on, simply rotate
the dimmer knob located on
your instrument cluster to
adjust the brightness.
2032271_16a_Mazda3_SSG_051215.indd 345/12/15 11:51 AM
www.MazdaUSA.com