2016 MAZDA MODEL 3 HATCHBACK clutch

When Driving
6For details, refer to Section 4, “Start/Stop Engine”.
Indicator light
Push button start
Starting the Engine
(SKYACTIV-D 1.5, SKYACTIV-D 2.2)
•The starter does not rotate until the glow indicator light turns off.
• When starting the engine, do not release the clutch pedal (manual transaxle) or
the brak
e pedal (automatic transaxle) until the glow indicator light in the
instrument cluster turns off and the engine starts, after pressing the push button
start.
1. Make sure the parking brake is on.
2. Continue to press the brake pedal firmly until
the engine has completely started.
3. (Manual transaxle)
Continue to press the clutch pedal firmly until
the engine has completely started.
(Automatic transaxle)
Put the vehicle in park (P). If you must restart the
engine while the vehicle is moving, shift into
neutral (N).
4. Press the push button start after both the KEY indicator
light (green) in the instrument cluster and the push button
start indicator light (green) illuminate.
• If the clutch pedal (manual transaxle) or the brake pedal (automatic transaxle) is
released before the engine starts, depress the clutch pedal (manual transaxle) or
the brak
e pedal (automatic transaxle) again and press the push button start to
start the engine.
• If the ignition is left switched ON for a long period of time without the engine
running after the glow plugs are warmed up, the glow plugs may warm up again
which will illuminate the glow indicator light.
/C\FCA(,'''A'FKVKQPA3WKEM)WKFGKPFD

When Driving
Manual transaxle
2. While depressing the clutch pedal, shift the shift lever to the neutral position.
Engine idling stops after the clutch pedal is released.
3.(SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5)
1. Stop the vehicle by depressing the brake pedal and then the clutch pedal.
The engine restarts automatically when you depress the clutch pedal or start to
release it.
NOTE
The engine restart timing varies depending on the brake pedal depression force.
Operation of i-stop Function
The i-stop function automatically stops the engine when the vehicle is stopped at a
traffic light or stuck in traffic, and then restarts the engine automatically to resume
driving. The system provides improved fuel economy, reduced exhaust gas
emissions, and eliminates idling noise while the engine is stopped.
NOTE
•When engine idling is stopped.
• The i-stop indicator light (green) turns on under the following conditions:
Engine idling stop conditions are met while the v
ehicle is being driven. •
(Except European model)
•The i-stop indicator light (green) turns off when the engine is restarted.
(SKYACTIV-D 1.5, SKYACTIV-D 2.2)
The engine restarts automatically when the clutch pedal is depressed.
7For details, refer to Section 4, “Start/Stop Engine”.
/C\FCA(,'''A'FKVKQPA3WKEM)WKFGKPFD

35
Maintenance and Care
Selector
X Mark MAX MIN
Owner Maintenance Precautions
Routine Service
We highly recommend that these items be inspected daily, or at least every week.
• Engine Oil Level
• Engine Coolant Level
• Brake and Clutch Fluid Level
• Washer Fluid Level
• Battery Maintenance
• Tyre Inflation Pressure
For details, refer to Section 6, “Owner Maintenance”.
Inspecting Engine Oil Level
If the engine oil level exceeds the “X” mark on the dipstick, replace the engine oil.
When inspecting the engine oil level, pull out the dipstick straight without twisting.
In addition, when inserting the dipstick, always insert it without twisting so that
the “X” mark faces the front of the vehicle.
Whenever the engine oil is replaced, the vehicles engine control unit needs to be reset as
soon as possible. Otherwise the wrench indicator light or engine oil warning light may
turn on. To reset the engine control unit, consult an expert repairer, we recommend an
Authorised Mazda Repairer or refer to the vehicle engine control unit reset procedure.
NOTE
The initialization (engine oil data resetting) of the recorded value can be
performed using the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the selector pressed, and press and hold the
selector for about 5 seconds until the master w
arning light flashes.
3. After the master warning light flashes for several seconds, the
initialization is completed.
/C\FCA(,'''A'FKVKQPA3WKEM)WKFGKPFD