2016 LINCOLN NAVIGATOR key

•
Various vehicle speed minders can be
set. Once you select a speed, it will be
shown in the display, followed by an
audible tone when the preselected
vehicle speed is exceeded.
• Audio system maximum volume of 45%.
A message will be shown in the display
when you attempt to exceed the limited
volume. Also, the speed-sensitive or
compensated automatic volume control
will be disabled. •
Always on setting. When this is selected,
you will not be able to turn off Advance
Trac or traction control, 911 Assist or
Emergency Assistance, or Do Not Disturb
(if your vehicle is equipped with these
features).
CREATING A MYKEY
Use the information display to create a
MyKey: 1. Insert the key you want to program into
the ignition. If your vehicle is equipped
with a push-button start, place the remote
control into the backup slot. The location
of your backup slot is in another chapter.
See Starting a Gasoline Engine (page
157).
2. Switch the ignition on.
3. Access the main menu on the information
display controls. Use the arrow keys to
get to the following menu selections: Action and Description
Message
Press the
OK button or the right arrow key.
Settings
Press the
OK button or the right arrow key.
MyKey
Press the
OK button or the right arrow key.
Create MyKey
When prompted, hold the
OK button until
you see a message informing you to label
this key as a MyKey. The key will be
restricted at the next start.
MyKey is successfully created. Make sure
you label it so you can distinguish it from the
admin keys. You can also program configurable settings
for the key(s). See Programming/Changing
Configurable Settings
.
Programming/Changing Configurable
Settings
Use the information display to access your
configurable MyKey settings.
1.
Switch the ignition on using an admin key
or remote control.
55
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™

2.
Access the main menu on the information
display controls. Use the arrow keys to get to the following menu selections: Action and Description
Message
Press the OK button or the right arrow key.
Settings
Press the
OK button or the right arrow key.
MyKey
Note: You can clear or change your MyKey
settings at any time during the same key
cycle as you created the MyKey. Once you
have switched the vehicle off, however, you
will need an admin key to change or clear
your MyKey settings. CLEARING ALL MYKEYS
You can clear or change your MyKey settings
using the information display control on the
steering wheel.
See Information Displays
(page 105). Switch the ignition on using an admin key or
remote control.
To clear all MyKeys of all MyKey settings, press the left arrow button to access the main menu and scr\
oll to: Action and Description
Message
Press the
OK button.
Settings
Press the
OK button.
MyKey
Press and hold the
OK button until the following message displays.
Clear MyKey
56
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™

Action and Description
Message
All MyKeys
Cleared
Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status.
57
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™

CHECKING MYKEY SYSTEM
STATUS
You can find information on programmed
MyKey(s) using the information display
control on the steering wheel. See
Information Displays (page 105).
To find information on programmed MyKey(s), press the left arrow button to access the main menu and scroll \
to: Description
Message
Press the
OK button.
Settings
Press the
OK button.
MyKey
Select one of the following:
Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance
is by using an admin key to clear your MyKeys. If the distance does not accumulate as expected,
then the intended user is not using the MyKey, or an admin key user recently cleared and then
recreated a MyKey.
MyKey Dist.
Indicates the number of MyKeys programmed to your vehicle. Use this feature to detect how many
MyKeys you have for your vehicle and determine when a MyKey has been deleted.
{0} MyKeys
Indicates how many admin keys are programmed to your vehicle. Use this feature to determine
how many unrestricted keys you have for your vehicle, and detect if an additional MyKey has
been programmed.
{0} Admin Keys
58
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™

USING MYKEY WITH REMOTE
START SYSTEMS
Vehicles With Ford-Approved
Aftermarket Remote Start Systems
When using a Ford-approved aftermarket
remote start system, the vehicle recognizes
the remote start system transmitter as an
additional admin key. It is the vehicle
’s
default setting.
When you start your vehicle with a
Ford-approved aftermarket remote start
system transmitter, the system shuts the
vehicle off after you open the door or shift
your vehicle into gear. This is intentional.
When you restart your vehicle, it reads the
vehicle key fob status instead of the remote
start system transmitter status. With a Ford-approved aftermarket remote
start system, it is possible to program all key
fobs as MyKeys unintentionally. If this
happens, then the remote start system
transmitter is the admin key. If you want to
have only one key fob as a MyKey, or do not
want to have any MyKeys, then you need to
use your remote start system transmitter to
clear all MyKeys. In that case, follow these
steps:
1. Enter your vehicle and close all doors.
2.
Start your vehicle using your remote start
system transmitter.
3. See Clearing All MyKeys (page 56).
Follow Steps 1-3.
After clearing your MyKeys, you can create
a new MyKey. See Creating a MyKey (page
55
).
Note: With push-button start, you cannot
program the remote start system transmitter
as a MyKey. Always treat the remote start
system transmitter as you would any other
admin key. Vehicles With Non-Ford-Approved
Aftermarket Remote Start Systems
MyKey is not compatible with
non-Ford-approved aftermarket remote start
systems. If you choose to install a remote
start system, see an authorized dealer for a
Ford-approved remote start system.
The following information may help if you
choose to install a non-Ford-approved
remote start system. The actions provided
below do not make MyKey compatible with
non-Ford-approved remote start systems,
but may help you retain some MyKey
functions.
When using a non-Ford-approved remote
start system, the vehicle may recognize the
remote start system as an additional admin
key with its associated privileges. If you
restart the vehicle by powering it off and
waiting a few seconds, and then powering
the vehicle back on, you may retain some
MyKey functions. This action forces your
vehicle to read the vehicle key fob instead
of the remote start system transmitter and
then uses the MyKey associated privileges.
59
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™

Note:
The MyKey system status menu
display may include the remote start system
as an additional key in the total count of
programmed keys. See Checking MyKey
System Status (page 58). With a non-Ford-approved aftermarket
remote start system, it is possible to program
all key vehicle key fobs as MyKeys
unintentionally. If this happens, then the
remote start system transmitter is the admin
key. If you want to have only one vehicle key
fob as a MyKey, or do not want to have any
MyKeys, then you need to use your remote
start system transmitter to clear all MyKeys.
In that case, follow these steps:
1. Enter your vehicle and close all doors. 2. Start your vehicle using your
non-Ford-approved remote start system
transmitter.
3. See Clearing All MyKeys (page 56).
Follow Steps 1-3.
After clearing your MyKeys, you can create
a new MyKey. See Creating a MyKey (page
55
).
Note: With push-button start, you cannot
program the remote start system transmitter
as a MyKey. Always treat the remote start
system transmitter as you would any other
admin key.
MYKEY TROUBLESHOOTING Potential Causes
Condition
The transmitter used to start the vehicle is not an admin key.
I cannot create a MyKey.
The transmitter used to start the vehicle is the only admin key. There always has to be at least one
admin key.
The transmitter is not in its backup position.
See Starting a Gasoline Engine (page 157).
The passive anti-theft system is disabled or in unlimited mode.
60
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™

Potential Causes
Condition
The vehicle has been started using a remote start system transmitter tha\
t is not an admin key. See
Using MyKey With Remote Start Systems (page 59).
The transmitter used to start your vehicle is not an admin key.
I cannot program the configurable
settings. There are no MyKeys programmed to your vehicle.
See Creating a MyKey (page 55).
The vehicle has been started using a remote start system transmitter tha\
t is not an admin key. See
Using MyKey With Remote Start Systems
(page 59).
The transmitter used to start your vehicle is not an admin key.
I cannot clear the MyKeys.
There are no MyKeys programmed to your vehicle.
See Creating a MyKey (page 55).
The vehicle has been started using a remote start system transmitter tha\
t is not an admin key. See
Using MyKey With Remote Start Systems
(page 59).
Purchase a new transmitter from an authorized dealer.
I lost the only admin key.
Program a spare transmitter.
See Passive Anti-Theft System (page 73).
I lost a key.
The vehicle has a remote start system transmitter that is recognized as \
an admin key. Clear all
MyKeys by using the remote start transmitter. See Using MyKey With Remote Start Systems
(page
59).
I accidentally programmed all keys as
MyKeys.
The vehicle's system does not recognize any programmed MyKeys. See Creating a MyKey (page
55).
An unknown transmitter has been created as a MyKey.
MyKey total includes one additional
key. The vehicle has a remote start system.
See Using MyKey With Remote Start Systems (page 59).
An unknown transmitter has been programmed to the vehicle as an admin key.
Admin key total includes one additional
key.
61
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™

Potential Causes
Condition
The vehicle has a remote start system. See Using MyKey With Remote Start Systems (page 59).
The MyKey is not being used by the intended user.
The MyKey distance does not accumu-
late. The MyKeys have been cleared and the MyKey system has been reset.
An admin transmitter is present at vehicle start.
No MyKey functions with the trans-
mitter. There are no MyKeys programmed to your vehicle.
See Creating a MyKey (page 55).
62
Navigator (TB5) Canada/United States of America, enUSA, First Printing MyKey™