2016 LEXUS LX570 light

438
LX570_OM_OM60N01U_(U)5-6. Using the other interior features
■Lighting conditions of operation indicator light
*: Depending on the portable device, there are cases where the operation indicator
light will continue being lit up orange even after the charging is complete.
●When the operation indicator light flashes
When an error occurs, the operation in dicator light flashes an orange color.
Handle the error based on the following table.
■The wireless charger can be operated when
The engine switch is in ACCESSORY or IGNITION ON mode.
■Usable portable devices
Qi standard wireless charge standard can be used on compatible devices.
However, not all Qi standard devi ces and compatibility are guaranteed.
Starting with mobile phones and smart phones , it is aimed for low power electrically sup-
plied portable devices of no more than 5W.
Operation indicator lightConditions
Tu r n i n g o f fWhen the Wireless charger power supply is off
Green (comes on)On Standby (charging possible state)
When charging is complete*
Orange (comes on)
When placing the portable device on the charging
area (detecting the portable device)
Charging
Operation indicator lightSuspected causesHandling method
Flashing repeatedly once
every second (Orange)Vehicle to charger commu-
nication failure.Contact your Lexus dealer.
Repeatedly flashes
3 times continuously
(Orange)
A foreign substance is
between the portable device
and charge area.Remove the foreign sub-
stance from between por-
table device and the
charge area.
The portable device is out of
sync due to the device being
shifted from its position.Place the portable device
near the center of the
charge area.
Repeatedly flashes
4 times continuously
(Orange)Te m p e r a t u r e r i s i n g w i t h i n
the wireless charger.Stop charging at once and
start charging again after
for a while.

LX570_OM_OM60N01U_(U)
4395-6. Using the other interior features
5
Interior features
■When covers and accessories are attached to portable devices
Do not charge in situations where cover and accessories not able to handle Qi are
attached to the portable devi ce. Depending on the type of cover and accessory, it may
not be possible to charge. When charging is not performed even with the portable
device placed on the charge area, remove the cover and accessories.
■While charging, noise enters the AM radio
Turn off the wireless charger and confirm th at the noise has decreased. If the noise
decreases, continuously pushing the power supply switch of the wireless charger for 2
seconds, the frequency of the charger can be changed and the noise can be reduced.
Also, on that occasion, the operation indicator light will flash orange 2 times.
■Important points of the wireless charger
●If the electronic key cannot be detected within the vehicle interior, charging cannot be
done. When the door is opened and closed , charging may be temporarily suspended.
●When charging, the wireless charging device and portable device will get warmer,
however this is not a malfunction.
When a portable device gets warm while charging, charging may stop due to the pro-
tection function on the portable device side . In this case, when the temperature of the
portable device drops significantly, charge again.
■Operation sounds
When the power supply is turned on, while se arching for the portable device a sound will
be produced, however this is not a malfunction.
■Certification for the wireless charger

442
LX570_OM_OM60N01U_(U)5-6. Using the other interior features
WA R N I N G
■Conditions in which the function may not operate correctly
In the following conditions, it may not operate correctly
●The portable device is fully charged
●There is foreign matter between the charge area and portable device
●The temperature of the portable device gets higher from charging
●The charging surface of the portable device is facing up
●The placement of the portable device is
out of alignment with the charge area
●Near a TV tower, electric power plant, gas station, radio station, large display, airport
or other facility that generates strong radio waves or electrical noise
●When the electronic key is in contact with , or is covered by the following metallic
objects
• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil inside
• Metallic wallets or bags
•Coins
•Hand warmers made of metal
• Media such as CDs and DVDs
●When other wireless keys (that emit radio waves) are being used nearby
In addition, excluding the above-mentioned, when the charger does not perform nor-
mally or the operation indicator light is flashi ng continuously, it is considered that the
wireless charger is malfunctioning. Contact your Lexus dealer.
■To prevent failure or damage to data
●Do not bring magnetic cards, such as credit cards, or magnetic recording media, etc.,
close to the charger while charging, otherw ise, data may disappear under the influ-
ence of magnetism. Also, do not bring pr ecision instruments such as wrist watches,
etc., close to the charger, as such objects may break.
●Do not leave portable devices in the cab in. The temperature inside the cabin may
become high, when under the sun, and cause damage to the device.
■To prevent battery discharge
When the engine is stopped, do not use the wireless charger for a long time.

446
LX570_OM_OM60N01U_(U)5-6. Using the other interior features
Garage door opener
The garage door opener (HomeLink® Universal Transceiver) is manufactured under
license from HomeLink®.
The HomeLink® compatible transceiver in your vehicle has 3 buttons which can
be programmed to operate 3 different devices. Refer to the programming
method below appropriate for the device.
Buttons
Indicator
■Programming HomeLink®
Point the remote control transmit-
ter for the device 1 to 3 in. (25 to
75 mm) from the HomeLink
®
buttons.
Keep the HomeLink® indicator light
in view while programming.
The garage door opener can be programmed to operate garage doors, gates,
entry doors, door locks, home lighting systems, security systems, and other
devices.
Programming HomeLink® (for U.S.A. owners)
1
2
1

LX570_OM_OM60N01U_(U)
4475-6. Using the other interior features
5
Interior features
Press and hold one of the
HomeLink® buttons and the
transmitter button. When the
HomeLink
® indicator light
changes from a slow to a rapid
flash, you can release both but-
tons.
If the HomeLink® indicator light
comes on but does not flash, flashes
rapidly for 2 seconds and remains lit,
the HomeLink
® button is already
programmed. Use the other buttons
or follow the “Reprogramming a
HomeLink
® button” instructions.
(  P. 4 4 9 )
Te s t t h e H o m e L i n k® operation by
pressing the newly programmed
button.
If a HomeLink® button has been
programmed for a garage door,
check to see if the garage door
opens and closes. If the garage door
does not operate, see if your remote
control transmitter is of the rolling
code type. Press and hold the pro-
grammed HomeLink
® button. The
remote control transmitter is of the
rolling code type if the HomeLink
®
indicator light flashes rapidly for 2
seconds and then remains lit. If your
transmitter is of the rolling code type,
proceed to the heading “Program-
ming a rolling code system”.
Repeat the steps above to program another device for each of the remain-
ing HomeLink® buttons.
2
3
4

448
LX570_OM_OM60N01U_(U)5-6. Using the other interior features
■Programming a rolling code system
If your device is rolling code equipp
ed, follow the steps under the heading
“Programming HomeLink
®” before proceeding with the steps listed below.
Locate the learn button on the ceiling mounted garage door opener motor.
The exact location and color of the bu tton may vary by brand of garage
door opener motor.
Refer to the operation manual supplied wi th the garage door opener motor for the
location of the learn button.
Press the learn button.
Following this step, you have 30 seconds in which to initiate step 3 below.
Press and hold the vehicle’s programmed HomeLink® button for 2 sec-
onds and release it. Repeat this step once again. The garage door may
open.
If the garage door opens, the programming process is complete. If the door does
not open, press and release the button a third time. This third press and release will
complete the programming process by opening the garage door.
The ceiling mounted garage door opener motor should now recognize the
HomeLink
® signal and operate the garage door.
Repeat the steps above to program an other rolling code system for any of
the remaining HomeLink® buttons.
■Programming an entry gate (for U.S.A. owners)/Programming all devices in
the Canadian market
Place your transmitter 1 to 3 in. (25 to 75 mm) away from the surface of the
HomeLink
®.
Keep the HomeLink® indicator light in view while programming.
Press and hold the selected HomeLink® button.
Repeatedly press and release (cycle) th e device’s remote control button for
two seconds each until step 4 is completed.
When the indicator light on the HomeLink
® compatible transceiver starts
to flash rapidly, release the buttons.
Test the operation of the HomeLink
® by pressing the newly programmed
button. Check to see if the gate/device operates correctly.
Repeat the steps above to program another device for each of the remain-
ing HomeLink
® buttons.
1
2
3
4
1
2
3
4
5
6

LX570_OM_OM60N01U_(U)
4495-6. Using the other interior features
5
Interior features
■Programming other devices
To program other devices such as home security systems, home door locks or
lighting, contact your Lexu s dealer for assistance.
■Reprogramming a button
The individual HomeLink
® buttons cannot be erased but can be repro-
grammed. To reprogram a button, fo llow the “Reprogramming a HomeLink®
button” instructions.
Press the appropriate HomeLink
® button. The HomeLink® indicator light
should come on.
The HomeLink® compatible transceiver in your vehi cle continues to send a signal for
up to 20 seconds as long as the button is pressed.
Press and hold the desired HomeLink® button. After 20 seconds, the
HomeLink® indicator light will start flashing slowly. Next, while still pressing and
holding the HomeLink® button, press and hold the button on the transmitter
until the HomeLink® indicator light changes from a slow to a rapid flash.
Press and hold the 2 outside buttons for
10 seconds until the indicator light
flashes.
If you sell your vehicle, be sure to erase
the programs stored in the HomeLink®
memory.
Operating HomeLink®
Reprogramming a HomeLink® button
Erasing the entire HomeLink® memory (all three programs)

451
LX570_OM_OM60N01U_(U)5-6. Using the other interior features
5
Interior features
LEXUS Enform Safety Connect
Microphone
LED light indicators
“SOS” button
: If equipped
Safety Connect is a subscription-based telematics service that uses Global
Positioning System (GPS) data and embe
dded cellular technology to provide
safety and security features to subscribers. Safety Connect is supported by
Lexus’ designated response center, wh ich operates 24 hours per day, 7 days
per week.
Safety Connect service is available by su bscription on select, telematics hard-
ware-equipped vehicles.
By using the Safety Connect service, yo u are agreeing to be bound by the
Telematics Subscription Service Agreement and its Terms and Conditions, as
in effect and amended from time to time, a current copy of which is available
at Lexus.com. All use of the Safety Connect service is subject to such then-
applicable Terms and Conditions.
System components
1
2
3