2016 Lexus GS450h rear view mirror

5
GS450h_QG_OM30F38U_(U)
OverviewInstrument Panel
Windshield wiper and washer switch P.37
Multi-information display P.30
Headlight switch Turn signal lever P.33
P.27
Inside lock buttons*
Trunk opener*
Hood lock release lever*
Driving position memory switches
P.21
See P.8
See P.7
Window lock switch*
Power window switches*
Door lock switches*
Outside rear view mirror switches*
Tilt and telescopic steering control switch
*

10
GS450h_QG_OM30F38U_(U)
OverviewRoof
Moon roof switches*
Inside rear view mirror*
“SOS” button P.87
Garage door opener switches P.83
Interior light*
Vanity lights*
: If equipped
*: Refer to “OWNER’S MANUAL”.
Personal lights*
Personal lights*

21
GS450h_QG_OM30F38U_(U)
Driving Position Memory
■Driving position memory
■
Recording procedure
Check that the shift lever is in P.
Turn the power switch to ON mode.
Adjust the driver’s seat, steering wheel, outside rear view mirrors and HUD (head-up
display) (if equipped) to the desired positions.
While pressing the “SET” button, or within
3 seconds after the “SET” button is pressed,
press button “1”, “2” or “3” until the buzzer
sounds.If the selected button has already been
preset, the previously recorded position
will be overwritten.
■Recall procedure
Check that the shift lever is in P.
Turn the power switch to ON mode.
Press one of the buttons for the driving
position you want to recall until the buzzer
sounds.
This feature automatically adjusts the front seats, steering wheel and outside rear view
mirrors to make entering and exiting the vehicle easier or to suit your preferences.
1
2
3
4
1
2
3

52
GS450h_QG_OM30F38U_(U)
BSM (Blind Spot Monitor) (if equipped)
Switching the BSM function
The Blind Spot Monitor functi on and Rear Cross Traffic Alert function can be switched
on and off using the multi-information display.
When switched on, the BSM indicator illuminates on the meter and the buzzer sounds.
Outside rear view mirror indicators
Blind Spot Monitor function:
When a vehicle is detected in the blind sp ot, the outside rear view mirror indicator
comes on while the turn signal lever is not operated and the outside rear view mirror
indicator flashes while the turn signal lever is operated.
Rear Cross Traffic Alert function:
When a vehicle approaching from the right or left rear of the vehicle is detected, the
outside rear view mirror indicators flash.
Rear Cross Traffic Alert buzzer (Rear Cross Traffic Alert function only)
When a vehicle approaching from the right or left rear of the vehicle is detected, a
buzzer sounds from behind the rear seat.
The Blind Spot Monitor is a system that has 2 functions;
● The Blind Spot Monitor function
Assists the driver in making th e decision when changing lanes
● The Rear Cross Traffic Alert function
Assists the driver when backing up
These functions use same sensors.
1
2
3

84
GS450h_QG_OM30F38U_(U)
■Programming HomeLink®
Press and release the HomeLink® button you want to program and check that the
HomeLink
® indicator light flashes (orange).
Perform within 60 seconds of , or the in dicator light will stop flashing and pro-
gramming will not be able to be completed.
Point the remote control transmitter
for the device at the rear view mirror,
1 to 3 in. (25 to 75 mm) from the
HomeLink
® buttons.
Keep the HomeLink
® indicator light
in view while programming.
For U.S.A. owners Press and hold the handheld transmit-
ter button until the HomeLink
® indica-
tor light changes fr om slowly flashing
orange to rapidly flashing green (roll-
ing code) or continuously lit green
(fixed code), then release the button.
Programming an entry gate (for U.S.A. owners)/Programming a device in the Cana-
dian market Press and release the remote control transmitter button at 2 second intervals, repeat-
edly, until the HomeLink
® indicator light changes from sl owly flashing (orange) to rap-
idly flashing (green) (rolling code) or continuously lit (green) (fixed code).
Te s t t h e H o m e L i n k
® operation by pressing the newly programmed button and observ-
ing the indicator light:
● Device with fixed code: If the indicator light is solid/continuous, programming has
been completed and your garage door or other device should operate when the
HomeLink
® button is pressed and released.
● Device with rolling code: If the indicator light flashes rapidly, your garage door
opener motor (or other device) is equipp ed with a rolling code. Complete the pro-
gramming process by firmly pressing and holding the programmed HomeLink
®
button for 2 seconds and then release the button.
● If the garage door or other device does not operate, proceed to “Programming a
rolling code system”.
1
31
2
3
3
4

94
What to do if...
GS450h_QG_OM30F38U_(U)
See the OWNER’S MANUAL
Tu r n s i g n a l i n d i c a t o r(Flashes faster)
PCS (Pre-Collision System)
warning light (if equipped)
Headlight indicator (U.S.A.)
BSM (Blind Spot Monitor)
outside rear view mirror indi-
cators (if equipped)
Tail light indicator (Canada)BSM (Blind Spot Monitor)
indicator (if equipped)
Headlight high beam indicatorBrake hold standby indicator
Automatic High Beam
indicator (if equipped)Brake hold operated
indicator
Cruise control indicatorSecurity indicator
Dynamic radar cruise control
indicator (if equipped)Low outside temperature
indicator
Cruise control “SET” indicator“READY” indicator
LKA (Lane-Keeping Assist)
indicator (if equipped)EV indicator
Intuitive parking assist
indicator (if equipped)
*2(U.S.A.)Parking brake
indicator
“AFS OFF” indicator
(if equipped)(Canada)
(Flashes)
Slip indicator“A I R B A G O N /
OFF” indicator
VSC OFF indicator
For further information, re fer to the OWNER’S MANUAL.